Used Heavy Duty Forklift for sale (13,952)

Condition: used, Diesel - forklift truck, compact forklift MORA type M80CS make no. 20087 year of construction 2006 Rated capacity 8 ton. Lifting height 3800 mm fork length 1800 mm fork carriage width 1460 mm overall height 3030 mm Hnedpfsitv Rdox Afisu Total width 1460 mm Total length without forks 3350 mm Dead weight 12740 kg - Duplex mast with 1950 mm free stroke - 4 cylinder PERKINS diesel engine - completely closed cab with heating - electro-hydraulic tipping device for the driver's cab - hydraulic auxiliary steering - 2 pieces working lights in front, 1 piece working light in the rear - yellow warning-flashing light on the protective roof - solid rubber tires (front 28 x 10 x 22) (rear 250/70 - 16) - 9646 operating hours read off - UVV-TÜV acceptance new good condition Renting on request

Condition: used, Schwerlaststapler von Svetruck in einem guten Zustand. Heavy duty forklift of Svetruck in good condition. Online-Video-Inspection by WhatsApp - MS Zoom - Telegram Hnsdpfxexdc Txe Afiju On Stock Emskirchen/Nürnberg - Available Immediately - Can be test

Condition: excellent (used), Year of construction: 1991, fuel type: diesel, ca. 16.800 h überholt 2019 Gabellänge 2.400 mm Dieselmotor VOLVO Tragkraft 15.000 kg Hubhöhe 3.000 mm Batterien neu 06/20222 Hnedpfx Afjib Iknjiou

Condition: used, Heavy-duty coil trolley, transport cart Very sturdy custom-built Load capacity: approx. 5 tons Length: 1500 mm Width: 1300 mm Height: 460/660 mm Ground clearance: 250 mm Overall length with fork sleeves: 1780 mm Fork pocket distance: 580 mm Maximum fork width: 200 mm Maximum fork thickness: 75 mm Hodpfx Afof Axnmeienu - 4 swivel castors, each with 2 wheels (wheel external diameter 250 mm) (Vulkollan polyurethane tire treads damaged) Steel wheels can also be used without the polyurethane coating - Equipped with fork pockets for easy handling and transport with a forklift - Safety bolts for securing the fork sleeves For transporting coils, shafts, bushings etc. using a forklift. The cart can be fully loaded and moved internally with a small forklift. Net weight: 585 kg Wheel external diameter: 250 mm Tread external diameter: 250 mm Tread internal diameter: approx. 220 mm Wheel width: 80 mm each (each swivel castor with twin wheels) Total length: 175 cm Total width: 130 cm The wheels require new surface coating; the type of Vulkollan or rubber can still be selected freely depending on requirements. Price for re-coating is approx. 900 EUR net (may vary depending on composition). Offer price with the damaged wheels.

Condition: new, Year of construction: 2025, pipe diameter (max.): 12,000 mm, travel distance X-axis: 12,000 mm, Equipment: cooling unit, safety light barrier, Three-chuck Heavy-duty Fiber Laser Tube Cutting Machine NS-12052HG 12000mm, 500 Chuck Servo drive is used for auxiliary feeding High-quality chuck Adaptive to different sizes of tubes Hnjdev D Uhfopfx Afieu Servo control, excellent performance Give the equipment ultra-high dynamic performance Auxiliary feeding system Reduce work intensity and improve efficiency More types of processed tubes Support flying cutting High-precision Z-axis control Bevel cutting Highly automated ≤2m workpieces are unloaded through servo flaps

Condition: excellent (used), Broadbent Heavy Duty Lathe 1041mm x 10,000mm Year approx. 1973. Swing over bed 1041mm (41”) Swing bin gap1575mm (62”) Hnodpfxewhylvj Afisu Distance between centres 9300mm (30’ 6”) Spindle bore 115m (4 ½”) Spindle speeds (18) 3.3 – 360 rpm Spindle motor 30 HP or 40 HP (To be confirmed) Tailstock 6 MT Imperial & Metric screw-cutting with change gears. 36” Faceplate with 4 adjustable jaws, 54” Faceplate, Taper turning attachment, Power feed to top slide, 2 x 18” 3 point steadies, 24”/28” Steady.

Condition: used, axle configuration: 3 axles, first registration: 01/2009, color: other, Year of construction: 2009, Empty weight: 9.040 kg Axle 1: left 8 mm right 8 mm Hnodpfx Afew Rfb Heieu Axle 2: left 10 mm right 10mm Axle 3: left 10 mm right 10 mm

Condition: ready for operation (used), throat depth: 1,100 mm, Heavy duty double column bandsaw sawing cap: dia 1100 mm autofeed with stroke of 500 mm (with unlimited repositioning) enlarged height of sawblade: 67 mm Hjdpfx Aexpggaefisnu chipconveyor equipped with fully motorized Weisshaupt rollerconveyors: - 6 meter in-feed rollerconveyor (outside) with 1 manual clamp for aligning workpiece - 3 meter in-feed rollerconveyor (inside) with 2 manual clamps for aligning workpiece - max workpiece width: 1100 mm - each roll is motorized - cap of one roll is 4 ton - 2 meter out-feed rollerconveyor - one rollerconveyor is equipped with scales to weigh workpiece after cutting (Sartorius system) Max height of workpiece: 1100 mm Length of band saw: 11400 x 67 x 1,6 mm

Condition: used, Year of construction: 1988, turning diameter over bed 2000 mm turning diameter over slide rest / mm turning length / mm - Type 1 K 671 320 F3 - Year of manufacture 1988 (first commissioned in 1998) - Turning length 10,000 mm - Turning diameter over bed 2,000 mm (modified) - Faceplate diameter 1,950 mm Hnedpfxsxn Tz Io Afieu - Faceplate clamping range 400 - 1,350 mm - Speeds 1.00 - 140 rpm - Torque 125,000 Nm - Main cutting force 130 kN max. - Automatic swiveling tailstock - Max. workpiece weight 70 tonnes - Max. workpiece weight with steady rest 100 tonnes - Drive power 100 kW - Number of bed ways 4 - Dimensions 22,000 x 6,200 x 2,900 mm - CNC control SIEMENS 840D (2010 for €220,000.00) - Support feed X-Z 0.3 - 4,000 mm/min. - Support rapid traverse X-Z 4,000 mm/min. - Inner cone dimensions 140 x 1:7 - The machine complies with CE guidelines - Includes 2 steady rests, 1 roller block, 4 jaws, boring device - Condition: very good condition

Condition: good (used), 19 heavy-duty conveyor rollers 238 mm Ø x 600 mm roller shell length with 40 mm Ø shaft and 2 pedestal bearings, with chain wheel 16 B1/Z= 17, 1 geared motor drive with fluid coupling, if required also 6 spiral rollers for right-hand discharge 238/266 mm Ø x 900 mm Hnsdpfx Afswb A Hveieu

Condition: used, functionality: fully functional, Year of construction: 2012, operating hours: 10,486 h, load capacity: 12,000 kg, lifting height: 4,000 mm, fuel type: diesel, mast type: duplex, construction height: 3,695 mm, fork carriage width: 2,500 mm, fork length: 2,400 mm, empty load weight: 21,300 kg, total length: 5,315 mm, drive type: Diesel, construction width: 2,530 mm, Heavy-duty forklift truck - diesel Load center: 1200 Fork width: 250 mm Hnsdoxn Dqgepfx Afisu Fork thickness: 100 mm Mast type: Duplex Gearbox: ZF 3WG171 Condition: Reconditioned with warranty Technical condition: Very good Front tires type: Air Front tires Size: 12.00-20 Front tires Condition: 80 - 100% Rear tires Type: Air Rear tires Size: 12.00-20 Rear tires Condition: 80 - 100% Zentralschmieranlage / central greasing system

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hodpoh U Rzgjfx Afienu Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: used, functionality: fully functional, machine/vehicle number: M9135*14687, Year of construction: 2013, operating hours: 16,230 h, load capacity: 42,000 kg, lifting height: 4,550 mm, fuel type: diesel, mast type: standard, construction height: 4,000 mm, power: 257 kW (349.42 HP), fork length: 2,500 mm, empty load weight: 53,800 kg, drive type: Diesel, Heavy-duty forklift - Diesel Chassis number: M9135*14687 Load centre: 1200 Mast type: Standard Transmission: Dana Clark TE27 Condition: Ready for operation and fully functional Technical condition: Good Front tyre type: Pneumatic Front tyre size: 18.00-25 Front tyre condition: 80 - 100% Rear tyre type: Pneumatic Rear tyre size: 18.00-25 Rear tyre condition: 60 - 80% Description: with coil or with new forks, both + €13,000.00 Side shifter, fork positioner, Heater, full cab, air conditioning, Hsdpfowt Hd Aox Afisnu rotating seat, person recognition, central lubrication system

Condition: ready for operation (used), total height: 3,340 mm, total length: 4,500 mm, total width: 1,950 mm, throat depth: 660 mm, Type: ONL 660x700 ACN Heavy duty double column bandsaw specific for high-alloy steels CNC touch control with saw parameters for various types of high-alloy steels cap round: dia 660 mm cap square: 660 x 700 mm bundle cap: 555 x 700 mm autofeed with stroke of 500 mm (with unlimited repositioning) sawing power: 18,5 kW the in-feed and sawing speeds are frecquency controlled enlarged height of sawblade: 67 mm chipconveyor equipped with fully motorized Weisshaupt rollerconveyors: - 10,3 meter in-feed rollerconveyor (outside) with 2 hydraulic clamps for aligning workpiece - 9 meter in-feed rollerconveyor (inside) with 2 hydraulic clamps for aligning workpiece - max workpiece width: 900 mm - each roll is motorized - cap of one roll is 4 ton - 4 meter out-feed rollerconveyor: one rollerconveyor is equipped with scales to weigh workpiece after cutting (Sartorius system) Max height of workpiece: 700 mm Sawspeed: 10 > 120 m/min Length of band saw: 8660 x 67 x 1,6 mm Power needed: 27 kW (58 amp) Weight: 8,5 ton (only machine) Hodpfx Asxpgggsfisnu

Condition: good (used), Year of construction: 2006, Puma 700M 2006 Doosan Puma 700M CNC Lathe (2006) Controlled axes: 3, X: 470 (450+20)mm, Z: 1650mm, C: 360(0.001)gr Tools in revolver: 12 (BMT85) Spindle RPM: 3-1500, Rotating tools RPM: 30-3000 Automatic door Weight: 16,100 kg Note that this lot is located at Braås, Sweden Hnjdpfx Ajxpdrtefieu

Condition: ready for operation (used), Year of construction: 1997, Immediately available ex stock: CNC heavy-duty lathe Bohringer VDF Model 16 M Year of manufacture: 1997 Sinumerik 840 C Swing over bed: 520 mm Swing over cross slide: 285 mm Turning length: 1,000 mm 2 turrets with 12 stations each Lower turret: 12 stations, 6 driven, 4 kW, speeds up to 6,000 rpm Upper turret: 12 stations, 6 driven, 4 kW, speeds up to 6,000 rpm NC controlled tailstock C axis for main spindle Power chuck, 200 mm diameter Spindle bore: 78 mm Hsdpfoxn Rzfox Afionu Drive power: 53 kW Chip conveyor Price: EUR 9,500 plus VAT, ex works.

Condition: new, Year of construction: 2025, Galen Buckets are Expert in Heavy Duty Bucket Manufacturing for the Mining Industry The machine model on the photo is CAT 390 Edge Length: 2350mm Hodpfjwfx N Isx Afijnu Capacity: 6.2m3 Detailed information and inquiry, please contact us

Condition: new, Year of construction: 2023, CAT950 Heavy Duty Bucket Hnjdpfx Afoqa Daxsiou For detailed information and quote, please contact us

Condition: new, Year of construction: 2024, Machine: Hyundai HX225 Edge Length: 1200mm Hjdpfx Asr Ar Anefionu Capacity: 1.2m^3 For detailed information and inquiries please contact us. Galen Group produces buckets for 20years

Condition: new, Year of construction: 2024, CAT950L Heavy Duty Bucket sales from STOCK Edge Length: 2850mm Capacity: 3.5m^3 Welded adapter-teeth Hnedpfxst Rqgto Afieu

Condition: new, Year of construction: 2024, Volvo EC350 Heavy Duty Bucket Edge Length: 1550mm Hedpfx Ajum D Ipsfisnu Capacity: 1.85m3

Condition: new, Width: 130 cm Warranty: 6 months Selling price: € 4.500, US$ 4.791 Bucket volume: 1.15 m^3 Machine: CAT320 Hodpon Tm Adofx Afionu Bucket Type: Heavy Duty Blade Length: 1300mm Capacity: 1.15m^3 Please contact for detailed information and bucket offers. Bucket production suitable for all brands and models 20 years of bucket production experience

Year of construction: 2021, condition: new, Attachment suited for: Construction machines When hard rock and rough terrain required high level of earth crushing force say hello to GALEN heavy duty rock ripper. Hsdpfx Aen Tm Tgsfijnu Single tooth ripper concentrates penetration power into single point. The body is made of Hardox or special casting shank that manufactured in own casting factory For detailed information, please contact us.

Condition: new, Width: 165 cm Warranty: 6 months Hnodon Tmzrepfx Afisu Bucket volume: 2.4 m^3

Year of construction: 2023, condition: used, Galen heavy duty mining bucket series are designed to withstand harsh mining conditions and efficiently transport large quantities of material. We can produce extreme heavy duty buckets for every +70tons machines Hnsdpfjn Tm I Hox Afiju