Used Bobst Sp 1080 E for sale (82)

Condition: good (used), Feeder ULTRASONIC DOUBLE SHEET DEVICE Stripping Station STRIPPING STATION Various Holhcov A N T Hjdw Honk MACHINE FOR PVC AND PLASTIC MATERIAL DIE-CUTTING IONIZATORS DEVICE ALL NEW ELECTRONIC SYSTEM HOT DEVICE ON THE SHEET 180 Ton 4.500 speed/hour

Condition: good (used), Year of construction: 1969, Functionality: fully functional, BOBST AUTOMATIC HOT FOIL STAMPING DIE CUTTING MACHINE • TYPE : SP 1080 E • SIZE : 78 x 108 cm • YEAR : 1969 (FEKET – 2014) Details: Hot Foil Stamping Machine Carton board min: 80 gr Carton board max: 800 gr Corrugated board max: 2 mm Sheet size min: 29,5x35 cm Sheet size max: 78x108 cm Speed max: 4000 s/h Stamping speed max: 4000 s/h Stamping & embossing size max: 78x108 (Longitudinal) Stamping & embossing size max. 78x108 (Transversal) Hnelhcdwsvm Dapo Hjk Die cutting size max: 78x108 Temperature max 180 ºC Foll length: 1000 meter Longitudinal: Web width advance shafts: 72 cm Transverse: Web width advance shafts 102 cm Max. pile height (feeder unit): 120 cm Max. pile height (delivery unit): 120 cm It is in very good condition Available immediately

Condition: good (used), Year of construction: 1998, operating hours: 25,571 h, Machine Step with safety barriers Centerline system for quick job changeover Electronic device for the sheet passage control Gripper bars Bobst-Electronic for the machine control Main motor Feeder Manual non-stop device Stack holder platform with automatic system for lateral correction via feelers (adjustable with Centerline marks) or manual system via a selector, during production Automatic movement of the stack holder platform adjustable in the direction of travel Synchronizer to regulate the arrival of sheets to the registers Pile height control at the front edge thanks to a photoelectric cell Lateral blowers adjustable with Centerline references Suction unit Safety system for lowering the pile try Introduction table Covered with an anti-static stainless steel plate Hnolhsv A Aatocdw Hjk Adjustable sheet synchronizer while running, allows to adapt the feeder cycle to that of the platen 4 Front lays, adjustable in pairs with front register control, with sheet presence Pull-lay operator side (OS) adjustable according to Centerline, with sheet control Pull-lay opposite operator side (OOS) adjustable according to Centerline, with sheet control Double sheet detector Sheet-hold down device (Introduction sheets guide in gripper) D-7 REINFORCED SHEET TRANSPORT EQUIPMENT for rigid and corrugate cardboard included: Introducers and upper belts - Upper transport elements (wide belts) Side-guided transport belts Upper frame with pneumatic lifting device Platin Grippers re-opening device Die-cutting device without band of gripper grip Equipment centering and locking Locking of the chase against the upper beam Measurement of the die-cutting force using an electronic probe Resocell: synthetic material supporting plate SHEET BRAKES DEVICE BY "BERNOULLI" SYSTEM ON PLATIN 1 Upper frame: with fixed bottom (E-1). Bottom sheet, 2 mm thick and synthetic protection plate, 1 mm thick 1 Cutting plate (E-4) Stripping Station 3 drawer frames system SHEET BRAKES DEVICE BY "BERNOULLI" SYSTEM ON STRIPPING STATION Quick locking device of the central stripping board on Waste Stripping Station 1 Upper pull-out frame (F-2) 1 Upper stripping equipment (F-21) required to create a waste stripping tool, including crossbars, clamps, stripper holders and stripping pins of 3, 5 and 10 mm of diameter 1 Fastening equipment for stripping die (F-22) Including crossbars and clamps 1 lower pull-out frame (F-8) F-81 lower stripping equipment for waste stripping (F-81) Including crossbars, pins and supports 1 "GRID" UPPER PULL-OUT FRAME WITH ALL ITS STANDARD TOOLS Delivery Pile tray Adjustable rear and side joggers with Centerline marks Sheet shredder special device Guillotine device for front trim with lateral evacuation belt G-5 AUTOMATIC NON-STOP ON DELIVERY SHEET BRAKES DEVICE BY "BERNOULLI" SYSTEM ON DELIVERY Conformity to standards and security The Autoplaten Presses SP 142-E is in conformity with the European Directives for the Safety and Health requirements related to its design and construction, sa well American standards UL 508 and NFPA related to industrial equipment Emergency Stops Operator safety devices Gripper Bar Chain Slip Clutch Gripper bar chain locking device Handling of the diecutting equipment Photoelectric cell safety barriers located at the feeder and at the delivery

Condition: used, Year of construction: 1973, The Bobst SP 1120-E is a punching machine equipped with a stripping unit, designed for efficient and precise punching operations. Manufactured by Bobst in 1973, this model is located in Germany, with pricing available upon request. It features a format of 780 x 1120 mm and can handle sheet sizes ranging from a maximum of 800 x 1120 mm to a minimum of 380 x 450 cm. The machine boasts a running speed of up to 6,000 sheets per hour and a cutting force of up to 300 tons. Additional features include a platform, pallet feeding with a non-stop device, sheet feeding (OS) with double sheet detection, and a centerline. Format: 780x1120 mm Equipment: Die Cutting Machine with Stripping Unit Sheet size: maxi 800x1120 mm - mini 380x450 cm Running speed: Max. 6000 Sheets/Hour Cutting force up to: 300 Tons Platform Helhcdwsv A R I Se Henk Pallet Feeder with Non-Stop device Pull guide (OS) with Double Sheet Detector Centerline

Year of construction: 1985, Condition: good (used), Bobst SP 130 E Hnolhcdjif Ed Dow Hjk Year 1985 Max.size: 920x1300 mm Min.Size: 450x580 mm Max.Speed: 7000 Sh/h Max. cutting force Cutting force: 500 T Centerline Immidiately available.

Condition: good (used), Year of construction: 1996, machine/vehicle number: 559803, BOBST AUTOPLATINE SP 1420 E Machine used in continuous operation. Used for the production of corrugated and solid board packaging. Maximum die format: Width: 1420 mm Length: 1020 mm Minimum format: Width: 700 mm Hslhcjvutwtedw Hjnk Length: 500 mm

Condition: good (used), Year of construction: 1994, operating hours: 46,000 h, Bobst SP 103-E, Year 1994 Die Cutting with Stripping Unit Sheet size: maxi 103x72 cm - mini 40x35 cm Running speed: Max. 8000 Sheets/Hour Cutting force up to: 250 Tons Counter: 46000 working hours Equipped with: . Non-Stop Feeder . Stream Feeder . Quick lock frame . Micrometric Hjlhcetdb Dcodw Honk . Stripping Unit with Quick lock upper chase and lower chase . Non-stop belt on delivery . With compressors, Tools, Manuals and Accessories

Condition: good (used), Year of construction: 1990, operating hours: 91,419 h, Machine ELEVATED 650 MM Step with safety barriers Centerline system for quick job changeover Electronic device for the sheet passage control Gripper bars Bobst-Electronic for the machine control Main motor Feeder AUTOMATIC ROLLER CONVEYOR ON FEEDER NON-STOP ON FEEDER WITH SWORDS AND AUTOMATIC GRID NO.6 ALUMINUM PALLETS FOR AUTOMATIC NON-STOP ON FEEDER Stack holder platform with automatic system for lateral correction via feelers (adjustable with Centerline marks) or manual system via a selector, during production Automatic movement of the stack holder platform adjustable in the direction of travel Synchronizer to regulate the arrival of sheets to the registers Pile height control at the front edge thanks to a photoelectric cell Lateral blowers adjustable with Centerline references Suction unit Safety system for lowering the pile try Introduction table Heljv A Aa Hjhcdw Hsnk Covered with an anti-static stainless steel plate Adjustable sheet synchronizer while running, allows to adapt the feeder cycle to that of the platen 4 Front lays, adjustable in pairs with front register control, with sheet presence Pull-lay operator side (OS) adjustable according to Centerline, with sheet control Pull-lay opposite operator side (OOS) adjustable according to Centerline, with sheet control Double sheet detector Sheet-hold down device (Introduction sheets guide in gripper) Upper frame with pneumatic lifting device D-7 REINFORCED SHEET TRANSPORT EQUIPMENT for rigid and corrugate cardboard included: Introducers and upper belts - Upper transport elements (wide belts) Side-guided transport belts Platin Grippers re-opening device Die-cutting device without band of gripper grip Equipment centering and locking Measurement of the die-cutting force using an electronic probe Resocell: synthetic material supporting plate 1 Upper frame: with fixed bottom (E-1). Bottom sheet, 2 mm thick and synthetic protection plate, 1 mm thick 1 Cutting plate (E-4) RESOCELL 22.5mm with 4mm compensation plate and 1mm metal sheet Extra E-55 ADJUSTABLE SUPPORTING PLATE CENTERINGS SHEET BRAKES DEVICE BY "BERNOULLI" SYSTEM ON PLATIN Upper chase for 23,8 mm Stripping Station 3 drawer frames system Quick locking device of the central stripping board on Waste Stripping Station 1 Upper pull-out frame (F-2) 1 Upper stripping equipment (F-21) required to create a waste stripping tool, including crossbars, clamps, stripper holders and stripping pins of 3, 5 and 10 mm of diameter 1 Fastening equipment for stripping die (F-22) Including crossbars and clamps 1 lower pull-out frame (F-8) F-81 lower stripping equipment for waste stripping (F-81) Including crossbars, pins and supports UPPER PULL-OUT FRAME QUICK LOCK ON STRIPPING UNIT WITH ALL ITS TOOLS CENTRAL PULL-OUT FRAME QUICK LOCK ON STRIPPING UNIT WITH ALL ITS TOOLS Delivery Pile tray Adjustable rear and side joggers with Centerline marks Braking Brush Front jogger Sheet shredder special device Guillotine device for front trim with lateral evacuation belt G-5 AUTOMATIC NON-STOP ON DELIVERY SHEET BRAKES DEVICE BY "BERNOULLI" SYSTEM ON DELIVERY LIGISTIC IN DELIVERY WITH CONVEYOR SYSTEM Security Emergency Stops Operator safety devices Gripper Bar Chain Slip Clutch Gripper bar chain locking device Handling of the diecutting equipment Photoelectric cell safety barriers located at the feeder and at the delivery

Year of construction: 1970, Condition: good (used), Bobst SP 1650 E Max.Size: 1150 x 1650 mm Min.Size: 570 x 850 mm Max.Speed: 4500 Sh/h Hslhcdwoht Rn Io Henk Year 1970 In good production condition.

Condition: good (used), Year of construction: 1974, Feeder Square type feeder head Push lay opposite operator side Pull lay operator side with double bearing kit for microwave Delivery Hnelhcdwjv A N Hme Hsk Non-stop delivery with belt convey Various Elevated 350 mm

Condition: good (used), Year of construction: 1986, operating hours: 76,215 h, Console Centerline Feeder Motorized suction head unit Pile feeder with automatic lateral moving Universal Feeder Non-stop on feeder with swords Introduction table Sheet-hold down device (Introduction sheets guide in gripper) Pull-lay operator side (OS) adjustable according to Centerline, with sheet control Receiving pull lay of the push lay operator side PULL LAY OPERATOR OPPOSITE SIDE (OOS) PUSHING LAY FOR CORRUGATE OPPOSITE OPERATOR SIDE (OOS) Electronic double sheet device D-7 REINFORCED SHEET TRANSPORT EQUIPMENT for rigid and corrugate cardboard included: Introducers and upper belts - Upper transport elements (wide belts) Adjustable sheet synchronizer while running, allows to adapt the feeder cycle to that of the platen Feed table with 4 front lays, adjustable in pairs with front register control Side-guided carrying straps Platin E-5 COMPENSATING PLATE. THICKNESS 4 MM. IN GROUND STEEL E-55 ADJUSTABLE SUPPORTING PLATE CENTERINGS Stripping Station 1 "GRID" UPPER PULL-OUT FRAME WITH ALL ITS STANDARD TOOLS CENTRAL PULL-OUT FRAME QUICK LOCK ON STRIPPING UNIT WITH ALL ITS TOOLS F-8 1 LOWER STRIPPING PULL-OUT FRAME WITH ALL ITS TOOLS F-22 Fastening equipment for stripping die (including crossbars and clamps) F-35 FASTENING EQUIPMENT FOR UPPER PULL-OUT FRAME QUICK LOCK DEVICE FOR STRIPPING (TO FIX STRIPPING TOOL TO THE UPPER PULL-OUT FRAME QUICK LOCK) F-2 : N. 1 Upper pull-out frame F-81 LOWER STRIPPING EQUIPMENT for waste stripping INCLUDING crossbars, pins and supports (installed on central pull-out frame F-8) Micrometric system with compensating plate and 1 mm small metals sheet Delivery Non-stop delivery with belt convey Holhcjv Ep N Tjdw Honk Safety sensors in delivery Guillotine device for front trim Various Elevated 350 mm

Condition: good (used), Year of construction: 2004, operating hours: 30,981 h, Machine Platform with safety barrier Centerline system for quick job changeover Electronic device for sheet travel control Adjustable centering at the stripping Air conditioning for the electrical cabinet Gripper bars C.U.B.E. (Control Unit Bobst Electronic) for machine management Main motor with frequency variator Feeder Pile-tray with handle allowing manual lateral correction of the pile during production Pile height control at the front edge thanks to a photoelectric cell Adjustable lateral blowers with Centerline references Pile rear guide (OS and OOS sides) Safety system for lowering the pile try Suction unit with multiple adjusting C-4 NON-STOP FEEDER MANUAL DEVICE C-8 VERTICAL POSITIONING OF THE SUCTION UNIT. Eliminates manual interventions to compensate for the flatness of the pile shape Introduction table Covered with an anti-static stainless steel plate Inlet table feeder 4 front lays, adjustable in pairs with front register control 1 Pull-lay operator side (OS) adjustable according to Centerline, with sheet control 1 Double sheet detector Support plates at entry of platen station 1 Sheet-hold down device (guiding the sheets to front lays) 1 Upper frame with manual lifting device 1 Upper transport equipment for paper, paperboard and corrugated board 4 Transport belts. With lateral guidance C-5 CONTROLLABLE SHEET ARRIVAL FOR PERFECT SYNCHRONIZATION OF SHEET ARRIVAL AND REDUCTION OF MACHINE STOPPAGES Platin Grippers re-opening device Die-cutting device without band of gripper grip Equipment centering and locking Locking of the chase against the upper beam Measurement of the die-cutting force with strain gauge Resocell: synthetic material supporting plate. Thickness 22.5 mm 1 Upper chase with quick locking: fixed bottom (E-3) Plate, thickness 2 mm and make-ready protection plate of syntetic material, 1 mm thickness 1 Cutting plate (E-4) E-5 COMPENSATION PLATE 4 mm thickness. it's useful for thin plate for repetetive work E 55 ADJUSTABLE SUPPORTING PLATE CENTERINGS : micromeric screws allow fine adjustment of counters mounted on the cutting plate with respect to the die (+/- 0,9 mm lengthwise and crosswise. Stripping Station 3 drawer frame system 1 Upper Stripping Frame (F-2) Holhcev Ep Suedw Hjnk 1 Upper stripping equipment (F-21) required to create a waste stripping tool, including crossbars, clamps, stripper holders and stripping pins of 3, 5 and 10 mm of diameter 1 Fastening equipment for stripping die (F-22) 1 Central drawer frame (F-71) 1 Fastening equipment stripping table (F-75) 1 lower pull-out frame (F-8) 1 Lower stripping equipment (F-81) Equipment for waste stripping including crossbars, pins and supports F-31 1 UPPER PULL-OUT FRAME QUICK LOCK. It reduces stripping tool assembly times; the quick-closing device allows the tool to be changed in the machine) F-35 1 FASTENING EQUIPMENT FOR UPPER PULL-OUT FRAME QUICK LOCK DEVICE FOR STRIPPING (TO FIX STRIPPING TOOL TO THE UPPER PULL-OUT FRAME QUICK LOCK) F-72 1 CENTRAL PULL-OUT FRAME QUICK LOCK F-76 1 FASTENING EQUIPMENT FOR STRIPPING TABLE ON CENTRAL PULL-OUT FRAME QUICK LOCK It allows to equip a stripping table to install it on central pull-out frame quick-lock Delivery Pile tray in delivery Adjustable rear and side joggers with Centerline marks 1 Braking brush Pneumatically controlled adjustable front joggers 1 Pushes the sheets down, ensuring good stacking G-5 AUTOMATIC NON-STOP ON DELIVERY Conformity to standards and security Operator safety devices Gripper Bar Chain Slip Cl...

Condition: good (used), Year of construction: 1968, Machine Pressure 500 Ton Machine complete with all its tools in order to work properly Introduction table Hneljv Rtm Hehcdw Hjk Pull lay operator side Stripping Station Stripping Station

Condition: good (used), Year of construction: 1997, operating hours: 38,460 h, Machine Platform with safety barrier Centerline system for quick job changeover Electronic device for sheet travel control Adjustable centering at the stripping and at the delivery Air conditioning for the electrical cabinet Gripper bars Bobst Electronic System for management of the machine Main motor with frequency variator Hnslhjv A Aa Tocdw Hsk F-9 PRE-SETTING TABLE : Adjustable. Allows the preparation of a second job during production, reducing machine makeready time and increasing the time available to run production. Requires: a series of supplementary stripping tools Feeder Pile-tray with handle allowing manual lateral correction of the pile during production Pile height control at the front edge thanks to a photoelectric cell Pile rear guide (OS and OOS sides) Adjustable lateral blowers with Centerline references Suction unit with multiple adjusting Safety system for lowering the pile try C-4 NON-STOP FEEDER MANUAL DEVICE C-8 VERTICAL POSITIONING OF THE SUCTION UNIT. Eliminates manual interventions to compensate for the flatness of the pile shape Introduction table Covered with an anti-static stainless steel plate 1 Inlet table feeder 4 front lays, adjustable in pairs with front register control 1 Pull-lay operator side (OS) adjustable according to Centerline, with sheet control 1 Double sheet detector Support plates at entry of platen station 1 Sheet-hold down device (guiding the sheets to front lays) 1 Upper frame with manual lifting device 1 Upper transport equipment for paper, paperboard and corrugated board 4 Transport belts. With lateral guidance C-5 CONTROLLABLE SHEET ARRIVAL FOR PERFECT SYNCHRONIZATION OF SHEET ARRIVAL AND REDUCTION OF MACHINE STOPPAGES Platin Grippers re-opening device Die-cutting device without band of gripper grip Equipment centering and locking Locking of the chase against the upper beam Measurement of the die-cutting force with strain gauge Resocell: synthetic material supporting plate. Thickness 22.5 mm 1 Upper chase with quick locking: fixed bottom (E-3) Plate, thickness 2 mm and make-ready protection plate of syntetic material, 1 mm thickness E-5 COMPENSATION PLATE 4 mm thickness. it's useful for thin plate for repetetive work E 55 ADJUSTABLE SUPPORTING PLATE CENTERINGS : micromeric screws allow fine adjustment of counters mounted on the cutting plate with respect to the die ( mm lengthwise and crosswise. Stripping Station 3 drawer frame system 1 Upper Stripping Frame (F-2) 1 Upper stripping equipment (F-21) required to create a waste stripping tool, including crossbars, clamps, stripper holders and stripping pins of 3, 5 and 10 mm of diameter 1 Fastening equipment for stripping die (F-22) 1 lower pull-out frame (F-8) 1 Lower stripping equipment (F-81) Equipment for waste stripping including crossbars, pins and supports F-31 1 UPPER PULL-OUT FRAME QUICK LOCK. It reduces stripping tool assembly times; the quick-closing device allows the tool to be changed in the machine) F-72 1 CENTRAL PULL-OUT FRAME QUICK LOCK Delivery Pile tray in delivery Adjustable rear and side joggers with Centerline marks 1 Braking brush Pneumatically controlled adjustable front joggers G-5 AUTOMATIC NON-STOP ON DELIVERY Conformity to standards and security Operator safety devices Gripper Bar Chain Slip Clutch Gripper bar chain locking device Handling of the diecutting equipment Emergency Stops

Condition: good (used), Year of construction: 2002, operating hours: 14,000 h, Machine Centerline system for quick job changeover PRE-SETTING TABLE : Adjustable. Allows the preparation of a second job during production, reducing machine makeready time and increasing the time available to run production. Requires: a series of supplementary stripping tools Platform covered with non-slip aluminum sheet with safety barrier Console CUBE control system Feeder Standard Feeder with all its equipment Non-stop device on feeder Pile-tray with handle allowing manual lateral correction of the pile during production Hnoljv A N N Uehcdw Hok Introduction table 1 Pull-lay operator side (OS) adjustable according to Centerline, with sheet control CONTROLLABLE SHEET ARRIVAL FOR PERFECT SYNCHRONIZATION OF SHEET ARRIVAL AND REDUCTION OF MACHINE STOPPAGES Platin Diecutting chase (fixed bottom plate) COMPENSATION PLATE 4 mm thickness. it's useful for thin plate for repetetive work E 55 ADJUSTABLE SUPPORTING PLATE CENTERINGS : micromeric screws allow fine adjustment of counters mounted on the cutting plate with respect to the die (+/- 0,9 mm lengthwise and crosswise. Upper chase conventional : fixed bottom Stripping Station UPPER PULL-OUT FRAME QUICK LOCK ON STRIPPING UNIT WITH ALL ITS TOOLS 1 Fastening equipment for stripping die (F-22); included bars and fixing brackets F-35 1 FASTENING EQUIPMENT FOR UPPER PULL-OUT FRAME QUICK LOCK DEVICE FOR STRIPPING (TO FIX STRIPPING TOOL TO THE UPPER PULL-OUT FRAME QUICK LOCK) 1 lower stripping frame with all its standard equipment Delivery Non-stop delivery with grill Various Cutting force 250 TON Board quality processable : carta (min. 80g/m²); cartone (250/2000 g/m²); corrugato "E" e "B" (max 4 mm.) Cutting size: with frontal cut (max. 705 x 1020 mm.); without front cut (max. 720 x 1020 mm.) 7.500 speed/h (depending on cardboard and type of iob feature) Pile height at feeder : With non-stop system (max. 1100 mm.) - Without non-stop system (max. 1.400 mm.) Complete with aluminium bars, supports for noddles and noddles CE Machine All books, electrical scheme, manual instruction books, spare parts books and standard tools Adjustable gripper grip from: 9 - 17 mm

Condition: good (used), Year of construction: 1979, Feeder Pull lay Various Thickness max. 4 mm Machine elevated Speed : 5000 sh/h Holhov A N Rljcdw Hjnk

Condition: good (used), Year of construction: 2002, operating hours: 21,588 h, Machine Platform safety barrier Centerline system for quick job changeover Electronic double sheet control Adjustable centering at the stripping and at the delivery Air conditioning for the electrical cabinet Gripper bars Main motor with frequency variator B-1 ELEVATED MACHINE Machine elevated 400 mm, included elevation of the steps B-42 ADDITIONAL INTERFACE "CUBE". It includes an additional screen and keyboard located on the feeder, operator side, which facilitate the management of the machine. F-9 PRE-SETTING TABLE : Adjustable. Allows the preparation of a second job during production, reducing machine makeready time and increasing the time available to run production. Requires: a series of supplementary stripping tools Feeder Pile-tray with handle allowing manual lateral correction of the pile during production Pile height control at the front edge thanks to a photoelectric cell Pile rear guide (OS and OOS sides) Adjustable lateral blowers with Centerline references Suction unit with multiple adjusting Safety system for lowering the pile try C-4 NON-STOP FEEDER MANUAL DEVICE C-8 VERTICAL POSITIONING OF THE SUCTION UNIT C-17 AUTOMATIC SIDE CORRECTION OF THE PILE Push lay opposite operator side Introduction table Covered with an anti-static stainless steel plate synchronization of the sheet adjustable at the stop, allows to adapt the speed of the feeder with which of the platin 4 front lays, adjustable in pairs with front register control Holhev A N Taecdw Henk Pull-lay operator side (OS) adjustable according to Centerline, with sheet control Double sheet detector Sheet-hold down device (guiding the sheets to front lays) Upper transport equipment for paper, paperboard and corrugated board Upper sheet transport equipment for paper, cardbord and corrugate cardboard to 4 mm thickness 4 Transport belts lateral guide C-5 CONTROLLABLE SHEET ARRIVAL FOR PERFECT SYNCHRONIZATION OF SHEET ARRIVAL AND REDUCTION OF MACHINE STOPPAGES D-1 PULL GUIDE (OOS) with device for sheet presence control. Pull adjustable with Centerline references D-3 PUSH GUIDE (OOS opposite operator side) WITH ELECTRONIC CONTROL useful for thick carton and corrugate D-73 FEED BELT SLOW-DOWN DEVICE Platin Grippers re-opening device Die-cutting device without band of gripper grip Equipment centering and locking Locking of the chase against the upper beam Measurement of the die-cutting force with strain gauge Resocell: synthetic material supporting plate. Thickness 22.5 mm 1 Upper chase with quick locking: fixed bottom (E-3) Plate, thickness 2 mm and make-ready protection plate of syntetic material, 1 mm thickness 1 Cutting plate (E-4) E-5 COMPENSATION PLATE 4 mm thickness. it's useful for thin plate for repetetive work E 55 ADJUSTABLE SUPPORTING PLATE CENTERINGS : micromeric screws allow fine adjustment of counters mounted on the cutting plate with respect to the die ( mm lengthwise and crosswise. E-56 LOWERING DEVICE FOR THE CHAINS-GUIDE Stripping Station 3 drawer frame system 1 Upper Stripping Frame (F-2) 1 Upper stripping equipment (F-21) required to create a waste stripping tool, including crossbars, clamps, stripper holders and stripping pins of 3, 5 and 10 mm of diameter 1 Fastening equipment for stripping die (F-22) 1 Central drawer frame (F-71) 1 Fastening equipment stripping table (F-75) 1 lower pull-out frame (F-8) 1 Lower stripping equipment (F-81) Equipment for waste stripping including crossbars, pins and supports B-23 SHEET BRAKING DEVICE USING BERNOULLI SYSTEM AT STR...

Condition: good (used), Year of construction: 2002, operating hours: 9,001 h, Machine Centerline System for Quick Job Changeovers CUBE control system Introduction table Pull-lay operator side (OS) adjustable according to Centerline, with sheet control D-1 PULL GUIDE (OOS) with device for sheet presence control. Pull adjustable with Centerline references Stripping Station Hnslhcdwowa Eugs Hsk Upper and lower stripping equipment (pins, bars, tools, etc.) 1 lower pull-out frame (F-8) F-31 1 UPPER PULL-OUT FRAME QUICK LOCK WITH ALL ITS TOOLS F-72 1 CENTRAL PULL-OUT FRAME QUICK LOCK ON STRIPPING UNIT Various 7.000 speed/h (depending on cardboard and type of iob feature) All books, electrical scheme, manual instruction books, spare parts books and standard tools

Condition: good (used), Year of construction: 1981, operating hours: 27,629 h, Machine Step with safety barriers Centerline system for quick job changeover Electronic device for the sheet passage control Bobst-Electronic for the machine control ELEVATED 300 mm Console Centerline Feeder Pile feeder with automatic lateral moving Non-stop on feeder with swords Motorized suction head unit Universal Feeder Introduction table synchronization to adjust the arrival of sheets to the registers Pull-lay operator side (OS) adjustable according to Centerline, with sheet control D-7 REINFORCED SHEET TRANSPORT EQUIPMENT for rigid and corrugate cardboard included: Introducers and upper belts - Upper transport elements (wide belts) Guide belt device on feeder table Hjlhov Ep Rwjcdw Honk Stripping Station F-2 : N. 1 Upper pull-out frame Delivery Guillotine device for front trim G-5 AUTOMATIC NON-STOP ON DELIVERY Various Micrometric system with compensating plate and 1 mm small metals sheet

Condition: good (used), Year of construction: 1974, Introduction table Hjlsv U Hivshcdw Henk Pull lay Stripping Station Stripping Station Various Thickness max. 4 mm Machine elevated Speed : 5000 sh/h

Condition: good (used), Year of construction: 2000, operating hours: 50,905 h, Console CUBE control system Feeder Pull lay operator side Non-stop on feeder Platin Die-cutting plate 4 mm Cutting plate with micrometric adjustment for 1 mm thin plates Stripping Station Stripping Pre make ready table 1 die-cutting upper stripping frame with Quick Lock Upper and lower stripping equipment (pins, bars, tools, etc.) Delivery Non-stop delivery with belt convey Hjlhcsv Ep Rqodw Hjnk Various 7.000 speed/h (depending on cardboard and type of iob feature) Normal die cutting plate 4 mm Centerline system for quick job changeover Elevated 300 mm Centerline System for Quick Job Changeovers

Condition: reconditioned (used), Year of construction: 1998, operating hours: 41,130 h, Machine Platform covered with non-slip aluminum sheet with safety barrier Centerline system for quick job changeover Electronic double sheet control Adjustable centering at the stripping and at the delivery Air conditioning for the electrical cabinet Gripper bars Bobst Electronic System for management of the machine Main motor with frequency variator C.U.B.E. (Control Unit Bobst Electronic) for machine management B-42 ADDITIONAL INTERFACE "CUBE". It includes an additional screen and keyboard located on the feeder, operator side, which facilitate the management of the machine. B-1 ELEVATED MACHINE Machine elevated 400 mm, included elevation of the steps B-41 ADDITIONAL INTERFACE "CUBE". It includes an additional screen and keyboard located on the feeder, operator side, which facilitate the management of the machine. Hnslhcdsv A N Nnsw Hok Feeder Automatic lateral pile adjusting Pile height control at the front edge thanks to a photoelectric cell Pile rear guide (OS and OOS sides) Adjustable lateral blowers with Centerline references C-4 NON-STOP FEEDER MANUAL DEVICE Suction unit with multiple adjusting Safety system for lowering the pile try C-17 AUTOMATIC SIDE CORRECTION OF THE PILE Introduction table Covered with an anti-static stainless steel plate 1 Inlet table feeder 4 front lays, adjustable in pairs with front register control 1 Pull-lay operator side (OS) adjustable according to Centerline, with sheet control 1 Double sheet detector Support plates at entry of platen station 1 Sheet-hold down device (guiding the sheets to front lays) 1 Upper frame with manual lifting device 1 Upper transport equipment for paper, paperboard and corrugated board 4 Transport belts. With lateral guidance 1 C-7 OMNIDIRECTIONAL ROLLERS AND BRIDGES FOR CORRUGATED CARDBOARD D-3 PUSH GUIDE (OOS opposite operator side) WITH ELECTRONIC CONTROL useful for thick carton and corrugate Platin Grippers re-opening device Equipment centering and locking Locking of the chase against the upper beam Measurement of the die-cutting force with strain gauge Resocell: synthetic material supporting plate. Thickness 22.5 mm 1 Upper chase with quick locking: fixed bottom (E-3) Plate, thickness 2 mm and make-ready protection plate of syntetic material, 1 mm thickness E-3 1 UPPER CHASE WITH QUICK LOCKING: FIXED BOTTOM E-5 COMPENSATION PLATE 4 mm thickness. it's useful for thin plate for repetetive work E 55 ADJUSTABLE SUPPORTING PLATE CENTERINGS : micromeric screws allow fine adjustment of counters mounted on the cutting plate with respect to the die ( mm lengthwise and crosswise. Stripping Station 3 drawer frame system 1 Upper Stripping Frame (F-2) 1 Upper stripping equipment (F-21) required to create a waste stripping tool, including crossbars, clamps, stripper holders and stripping pins of 3, 5 and 10 mm of diameter 1 Fastening equipment for stripping die (F-22) 1 Central drawer frame (F-71) 1 Fastening equipment stripping table (F-75) 1 lower pull-out frame (F-8) 1 Lower stripping equipment (F-81) Equipment for waste stripping including crossbars, pins and supports B-23 SHEET BRAKING DEVICE USING BERNOULLI SYSTEM AT STRIPPING SECTION. Includes braking tablets that are used with the Bernoulli system. It allows better maintenance of the back part of the sheets of light material F-31 1 UPPER PULL-OUT FRAME QUICK LOCK. It reduces stripping tool assembly times; the quick-closing device allows the tool to be changed in the machine) F-35 1 FASTENING EQUIPMENT FOR UPPER PULL-OUT FRAME QU...

Condition: reconditioned (used), Year of construction: 1991, Machine Centerline Feeder Standard Feeder with all its equipment Non-stop device on feeder Hnelhov A N S Ascdw Hek Pile height at feeder : With non-stop system (max. 1100 mm.) - Without non-stop system (max. 1.400 mm.) Platin Diecutting chase (fixed bottom plate) Normal die cutting plate 4 mm Stripping Station 1 die-cutting upper stripping frame 1 lower stripping frame with all its standard equipment Compete with aluminium bars, needles supports and needles Various Cutting force 250 TON Board quality processable : carta (min. 80g/m²); cartone (25 g/m²); corrugato "E" e "B" (max 4 mm.) Cutting size : with front trim ( max. 705 x 1020 mm.); without front trim (max. 720 x 1020 mm.) 7.500 speed/h (depending on cardboard and type of iob feature) All books, electrical scheme, manual instruction books, spare parts books and standard tools Adjustable grippers 8-17 mm Tavolo di introduzione Pull lay operator side

Condition: reconditioned (used), Year of construction: 2007, operating hours: 12,565 h, Machine B-28 INSTALLATION OF THE MACHINE WITHOUT EXCAVATION B-7 PLATFORM Macchina compatible with HIGHWAY TDF VIEW System Centerline system for quick job changeover Hnolev Ep Nyohcdw Hok Electronic device for sheet travel control Adjustable centering on delivery Control cabinet cooling unit C.U.B.E. (Control Unit Bobst Electronic) for machine operation Main motor with frequency variator Feeder Pile tray with handle allowing manual lateral correction on the pile during production Synchronization device timing the sheet arrival against the front lays when the machine is at a standstill Pile lifting controlled by Pressfoot Rear pile guide (OS and OOS sides) Side blowers adjustable with Centerline marks Suction unit Safety system for lowering the pile try C-4 NON-STOP FEEDER MANUAL DEVICE Platin Grippers re-opening device (Platin) Equipment centering and locking on platin Synthetic material supporting plate on platen (Thickness 23.5 mm (0,925") E-5 COMPENSATING PLATE. THICKNESS 4 MM. IN GROUND STEEL E-55 ADJUSTABLE SUPPORTING PLATE CENTERINGS 1 Upper chase-fixed bottom (E-1) 1 Cutting plate (E-4) Stripping Station Quick locking device of the central stripping board Motorized lifting of the upper frame 1 Upper Stripping Frame (F-2) 1 Upper stripping equipment (F-21) required to create a waste stripping tool, including crossbars, clamps, stripper holders and stripping pins of 3, 5 and 10 mm of diameter Fastening equipment for stripping die (F-22) 1 Adaption material for stripping board on the central frame (quick locking) (F-76) 1 lower pull-out frame (F-8) 1 Lower stripping equipment (F-81) Equipment for waste stripping including crossbars, pins and supports F-31 UPPER PULL-OUT FRAME QUICK LOCK DEVICE FOR STRIPPING ((decreases extraction tool assembly times. the quick-closing device allows the tool to be changed in the machine) F-35 FASTENING EQUIPMENT FOR UPPER PULL-OUT FRAME QUICK LOCK DEVICE FOR STRIPPING (TO FIX STRIPPING TOOL TO THE UPPER PULL-OUT FRAME QUICK LOCK) CENTRAL PULL-OUT FRAME QUICK LOCK ON STRIPPING UNIT WITH ALL ITS TOOLS Various The Autoplaten Presses SP 106-E are in conformity with the European Directives for the Safety and Health requirements related to its design and construction, sa well American standards UL 508 and NFPA related to industrial equipment Tavolo di introduzione Covered with an anti-static stainless steel plate Transport belts (with lateral guidance and automatic tensionning system) 4 front lays, adjustable in pairs with front register control "Pull" guide (OS) adjustable according to Centerline marks, with side register control Double sheet detector. Mechanical, integrated on pull guide (OS) Sheet-hold down device (guiding the sheets to front lays) Upper transport equipment for paper, paperboard and corrugated board C-5 SYNCHRONIZATION DEVICE TIMING THE SHEET ARRIVAL AGAINST THE FRONT LAYS WHEN THE MACHINE IS AT A STANDSTILL D-1 PULL GUIDE (OOS)

Condition: good (used), Year of construction: 2005, operating hours: 25,593 h, Machine Centerline system for quick job changeover Electronic device for sheet travel control Adjustable centering on delivery Control cabinet cooling unit C.U.B.E. (Control Unit Bobst Electronic) for machine operation Main motor with frequency variator B-7 PLATFORM B-28 INSTALLATION OF THE MACHINE WITHOUT EXCAVATION M-5 CHASE CHANGER : allows the change and preparation of the chase and the die cutting corresponding to the next job (Includes an increase in the surface of the platform) Feeder Pile tray with handle allowing manual lateral correction on the pile during production Synchronization device timing the sheet arrival against the front lays when the machine is at a standstill Pile lifting controlled by Pressfoot Rear pile guide (OS and OOS sides) Side blowers adjustable with Centerline marks Suction unit Hnolhcdsv A N N Iow Hsk Safety system for lowering the pile try C-4 NON-STOP FEEDER MANUAL DEVICE Platin Grippers re-opening device (Platin) Cutting plate with micrometric adjustment for 1 mm thin plates Equipment centering and locking on platin Synthetic material supporting plate on platen (Thickness 23.5 mm ( Upper chase-fixed bottom (E-1) E-5 COMPENSATING PLATE. THICKNESS 4 MM. IN GROUND STEEL E-55 ADJUSTABLE SUPPORTING PLATE CENTERINGS E-3 1 UPPER CHASE QUICK-LOCK: FIXED BOTTOM PLATE, THICKNESS 2 MM, AND MAKE-READY PROTECTION PLATE MADE OF SYNTETHIC MATERIAL, THINCKNESS 1 MM. 1 Cutting plate (E-4) Stripping Station Quick locking device of the central stripping board Motorized lifting of the upper frame F-2 1 Upper Stripping Frame F-31 UPPER PULL-OUT FRAME QUICK LOCK DEVICE FOR STRIPPING ((decreases extraction tool assembly times. the quick-closing device allows the tool to be changed in the machine) 1 Upper stripping equipment (F-21) required to create a waste stripping tool, including crossbars, clamps, stripper holders and stripping pins of 3, 5 and 10 mm of diameter Fastening equipment for stripping die (F-22) CENTRAL PULL-OUT FRAME QUICK LOCK ON STRIPPING UNIT WITH ALL ITS TOOLS 1 Adaption material for stripping board on the central frame (quick locking) (F-76) 1 lower pull-out frame (F-8) 1 Lower stripping equipment (F-81) Equipment for waste stripping including crossbars, pins and supports F-35 FASTENING EQUIPMENT FOR UPPER PULL-OUT FRAME QUICK LOCK DEVICE FOR STRIPPING (TO FIX STRIPPING TOOL TO THE UPPER PULL-OUT FRAME QUICK LOCK) Delivery Adjustable rear and side joggers with Centerline marks in delivery G-5 AUTOMATIC NON-STOP BELT : it is automatically introduced on delivery when the pile of sheets is finished Various Cutting force 260 TON 7.700 speed/h (depending on cardboard and type of iob feature) Board quality processable : carta (min. 80g/m²); cartone (25 g/m²); corrugate* (3 - 4 mm.) ( * ) Carton acceptable warp : 4% of the widthwise sheet Compliant with European Directives for essential safety and health standards relating to design and construction and with American standards UL 508 and NFPA concerning industrial equipment Tavolo di introduzione Covered with an anti-static stainless steel plate Transport belts (with lateral guidance and automatic tensionning system) 4 front lays, adjustable in pairs with front register control Pull-lay operator side (OS) adjustable according to Centerline, with sheet control Double sheet detector. Mechanical, integrated on pull guide (OS) Sheet-hold down device (guiding the sheets to front lays) Upper transport equipment for paper, paperboard and corrugated board C-5 SYNC...