Used Rippert/Maxon/Weishaupt Coating Line for sale (11,340)

Condition: ready for operation (used), Year of construction: 2017, Two Weishaupt gas burners including two WMG boilers are available. Output: 2x3.3MW. Documentation available. An on-site inspection is possible. Nodpext Rlnjfx Afajla

Condition: ready for operation (used), Year of construction: 1997, A misted Rippert wet separator system in stainless steel design is available for the painting process. Working width: 5000mm, exhaust air capacity: 18000m³/h, water capacity: 700l. Stainless steel chimney included. On-site inspection is possible. Nljdpfx Afswydgzjaja

Condition: ready for operation (used), Year of construction: 2013, An old steam boiler Loos including a relatively new Weishaupt burner is available. 1) Steam boiler Loos UL-S, year of manufacture: 1991, steam output: 6000kg/h, max. operating overpressure: 13bar, boiler volume: 6380l. 2) Weishaupt burner G50/2-A, year of manufacture: 2013, output range: 600kW-5400kW, connection pressure range: 15mbar-500mbar. Documentation available. An on-site inspection is possible. Nlodpfx Ajx Uq T Rofaja

Condition: ready for operation (used), Year of construction: 2022, An originally packaged Weishaupt burner is available. Thermal output range: 145kW-570kW, flame head: W40/1, typical pump pressure setting: 12bar, weight: approx. 40kg. Documentation available. An on-site inspection is possible. Nedpfx Afsx Uq Uzeaola

Year of construction: 2022, condition: ready for operation (used), Three burners are available. 1) Elco. 2) Seibold WV 500, year of construction: 2022, fuel: light oil EL, calorific value: approx. 10kWh/l, fuel flow rate: approx. 160l/h, nominal heat output: 1600kW, pilot burner fuel: propane, propane calorific value: approx. 26kWh/nm³, propane pre-pressure: 100mbar, max. chamber temperature: 270°C, max. chamber pressure: 3mbar. 3) Weishaupt, year of construction: 1999, output range: 474kW-2491kW. On-site inspection is possible. Nlodswl I A Djpfx Afaea

Condition: ready for operation (used), Year of construction: 2016, Stainless steel kneading bowl Nledpfxov Twgpj Afaea Manufacturer - Bago-Line/Sottoriva. Model - Twist 90/1. Year - 2016. Voltage - 3x400V. Electric power - 6.5kW. Water dosing included. 90 liter kettle. CLH.24

Condition: good (used), radial fan, dust extraction blower, fan, extraction, dust blower -for: paint wall, paint booth -Motor: Explosion-proof -Engine power: 5.0 kW Nodpfx Aeca Iarofasla -Speed: 1455 rpm -Inlet connection: Ø 430 mm -Outlet connection: Ø 450 mm -Impeller: Ø 660 mm -Dimensions: 1350/900/H1240 mm -Weight: 236 kg

Condition: good (used), Year of construction: 1992, radial fan, dust extraction blower, fan, extraction, dust blower -Motor power: approx. 3 kW -Inlet connection: Ø 230 mm -Output connection: 335 x 290 mm -Impeller: Ø 340 mm -Dimensions: 540/580/H660 mm Nodpfx Afob Rh U Tjaela -Weight: 80 kg

Year of construction: 2000, condition: used, centrifugal fan, dust extraction fan, fan, suction, dust blower -Manufacturer: Rippert, centrifugal fan in soundproof housing -Type: HL560/710-200 -Motor: 5 kW 1435 rpm -Volume flow: 12,000 m³/h -Inlet/Outlet connection: Ø 500 mm, see photos -Dimensions: 1945/1515/H2350 mm Nledpfx Afslzmyloaea -Weight: 600 kg

Condition: used, Hydraulic cylinder, synchronous cylinder, steering cylinder -Piston diameter: 38 mm -Piston rod: Ø 16 mm (M12 thread) -Stroke: 20 mm Nodsdkf I Tjpfx Afaola -Dimensions: 234/89/H50 mm -Weight: 3 kg

Condition: used, Centrifugal fan, dust extractor fan, fan, extractor, dust fan Nlsdedq Dcpjpfx Afaea -for: painting wall, painting booth -Motor: Ex protected -Motor power: 3.6 kW -Speed: 1440 rpm -Connection input: O mm -Connection output: 450 mm -Dimensions: 1260/1100 / H815 mm -Weight: 188 kg

Condition: new, functionality: fully functional, Year of construction: 2025, Aggregate and ballast crusher equipment are used in the crushing and processing of various materials for construction and infrastructure projects. These crushers are designed to break down large rocks, gravel, or stones into smaller pieces, producing aggregates and ballast that are essential components in the construction industry. Here are some key aspects related to aggregate and ballast crusher equipment: 1. Jaw Crusher: - Jaw crushers are commonly used for primary crushing in aggregate and ballast production. They operate by compressing the material between a stationary and a movable jaw. 2. Impact Crusher: - Impact crushers are suitable for shaping and producing fine aggregates. They use impact force to crush the material, making them suitable for various types of rock and ore. 3. Cone Crusher: - Cone crushers are often used for secondary and tertiary crushing in aggregate production. They are efficient for producing well-shaped and finely graded aggregates. Nlsdpfx Afsq Nxrxeaja 4. Vertical Shaft Impact (VSI) Crusher: - VSI crushers are designed for shaping and producing high-quality artificial sand. They use the "rock-on-rock" crushing principle, where rocks are fed into the rotor to be accelerated and crushed against the stationary anvils. 5. Gyratory Crusher: - Gyratory crushers are primarily used in mining, but they may also be used in the production of aggregates. They have a conical head and a concave surface, which crushes the material between the head and concave. 6. Mobile Crushers: - Mobile crushers, including mobile jaw crushers and mobile impact crushers, provide flexibility and mobility for on-site crushing of aggregates and ballast. They are often used in construction projects where materials need to be processed directly at the job site. 7. Screens and Scalpers: - Screens and scalpers are used to separate different sizes of aggregates after the initial crushing stage. Vibrating screens are commonly employed to classify and separate materials based on size. 8. Conveyors: - Conveyors are crucial for transporting materials between various stages of the crushing process and for stockpiling the final products. They enhance efficiency in material handling. 9. Dust Suppression Systems: - Crushing operations can generate dust, and dust suppression systems are used to minimize environmental and health impacts. These systems may include water sprays or chemical suppressants. 10. Quality Control: - Quality control measures, such as particle size analysis and gradation testing, are essential to ensure that the produced aggregates and ballast meet the required specifications and standards. 11. Environmental Considerations: - Crusher equipment should adhere to environmental regulations, and measures like dust control, noise reduction, and proper waste disposal should be implemented. When selecting aggregate and ballast crusher equipment, factors such as the type of material, required product size, production capacity, and mobility requirements should be taken into consideration. Additionally, adherence to safety and environmental standards is crucial in the operation of crushing equipment.

Year of construction: 2008, condition: used, Labelling Machine / Marking System SRD Stano-/Alone-Line Features: * Used labelling machine with integrated marking system * Very robust construction * Condition: fully functional with signs of use * Ideal for fast material handling * Professionally dismantled and packaged Year of manufacture: 2008 Technical Data: Manufacturer: SRD Model: Stano/- Alone-Line Unit: Valentin SPE 106/12 Internal article number: 2026012704 Nljdpfeyfgp Ujx Afaea Semi-automatic marking system for image and audio media Refer to the operation manual, wiring diagram, and pneumatic diagram for details Tailor-made solutions for your intralogistics. Whether roller conveyors, belt conveyors, inclined conveyors, or telescopic conveyors for loading and unloading your goods – we are your competent partner! We are happy to provide you with a custom quote or assist you with planning or installation questions. Simply let us know your requirements and local conditions. Benefit from our many years of experience and excellent network of professionals. We have successfully completed projects for companies from various industries, such as logistics, pharmaceutical, trades, and electronics. Together, we will develop ways to optimize your processes and material flow cost-effectively and sustainably. We can also supply fully automated sorting technology or additional components such as picking racks or containers.

Condition: excellent (used), Year of construction: 2019, Manufacturer: Weishaupt Type: WM-G20/3-A Quantity: 2 units Year of manufacture 2019 Nsdpfjvw U S Rox Afasla Power: 2000 kW

Condition: like new (used), RR120 is a high-volume system for printing, coating, inspecting, and drying rolls. Its modular design offers flexibility for specific applications and needs Reel to Reel Handling System Nodpfx Ajya Hvqjfasla 7 Dispensing Channels (Tandem Pumps Bio-Jet, Front Line and Air Jet Dispensing Technologies Print up to 7 Lines Simultaneously Automated Dispense Tracking for Precision Line Placement Perform Multiple Applications on One System Adjustable Tension for Handling Backed/Unbacked Membranes Easy to Set up, Operate and Maintain Data Storage to Support Multiple Applications Many System Options Can be Upgraded after Purchase

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 3,500 mm, total length: 7,050 mm, total width: 4,100 mm, volume flow: 36,000 m³/h, temperature: 80 °C, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), Equipment: cabin, lighting, Paint and Drying Booth It is the centerpiece of your entire painting operation: the combined paint and drying booth. Nodpjxa H Ewefx Afasla (Alternatively available as a separate paint booth with a dedicated dryer.) Our solutions feature full-surface ceiling filters and, optionally, full-surface floor extraction with drive-over grating or wall extraction at the position of your choice. If you wish to further increase the efficiency of the system beyond heat recovery and infinitely variable control via frequency converter, we can also offer you a sectional control system. This enables you, for example when doing spot repairs or partial booth loading (such as painting only add-on parts), to activate only the section where the parts are located. This allows you to operate with a reduced air volume, save energy, and minimize costs, all without compromising quality. Feel free to contact us – we would be happy to demonstrate these options in detail. Do you have any questions or suggestions? We are happy to assist you.

Condition: new, Year of construction: 2025, total height: 4,000 mm, total length: 7,000 mm, total width: 3,000 mm, warranty duration: 24 months, temperature: 80 °C, air demand: 36,000 m³/h, input voltage: 380 V, heating capacity: 345 kW (469.07 HP), power: 40 kW (54.38 HP), fuel: liquid petroleum gas (LPG), energy consumption: 40 kWh, insulation material: Mineralwolle, insulation thickness: 50 mm, nominal power: 345 kW (469.07 HP), Equipment: lighting, MAIN STANDARD Our paint booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. Booth processes are managed via a PLC system, ensuring that desired values are maintained consistently. OPERATING PRINCIPLES OF THE BOOTH The booth’s processes are managed through a control panel, which oversees the following steps: PAINTING PROCESS During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (paint stop filters) collect paint particles, and the air passes through final exhaust filters before being discharged. FLASH-OFF PROCESS After painting, the booth continues operating for approximately 15 minutes to purge residual solvents and thinners. During this phase, fresh air circulates from outside into the booth. DRYING PROCESS In this stage, 80% of the air passing through the booth is heated to 60°C and introduced via a distribution system. Since 20% of the solvent is released during drying, it is expelled with the exhaust air. Industrial coatings are typically dried at 60°C, but the booth temperature can be adjusted as needed via the control panel. Njdpfx Afswzmcbjasla COOLING PROCESS After the 30-minute drying cycle, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the subsequent 5-minute cooling phase, fresh air from outside circulates through the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels govern the functions and operation of machines and devices housed within the booth. The panel is made of durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical Equipment and Control Panel: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to accommodate booth relocation if needed. • Operating equipment uses 380 V 50 Hz, while control devices operate at 220 V. • The booth’s operation time can be monitored on the electronic control panel, enabling straightforward maintenance scheduling. • Temperature and time settings for booth ventilation (solvent flash-off), intermediate drying, and final drying can be easily adjusted to required values on the digital display of the electronic control panel. • Users can monitor and adjust the drying time using the heating thermostat and time relay.

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Nlsdpfxjwzl Hxo Afaoa Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: PEF-2.5 PULVER EINBRENNOFEN ELEKTRISCH, temperature: 230 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, inner dimension width: 1,505 mm, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ ⭐ Powder furnace with electric heating - ✔️ Internal dimensions: 2500 mm L * 1505 mm W * 1800 mm H ✔️ Electric heating output: 30 kW/h ✔️ Fan: 3000 m3/h 80 mm SS ✔️ Circulation fan output: 1.5 kW/h ✔️ Total 35 kW/h +- 10% ✔️ Digital heat control, continuously adjustable temperature up to 220°C ✔️ Sandwich panels inside: 1.5 mm galvanized steel, outside: 1.5 mm powder-coated Steel ✔️ Adjustable curing temperature, curing time, and exhaust fan function ✔️ An audible signal sounds at the end of the curing time ✔️ Insulated door with special locking systems (snap lock) ✔️ Insulation: 150 mm (150 mm rock wool) 🔥 PEF-2.5 Curing Oven: Your versatile industrial oven for drying and curing processes! 🔥 Whether powder coating, wet paint, plastic processing, or other thermal processes – the powder curing oven is your reliable solution for professional curing and drying processes up to 230°C! 🌡️ _____ 🚚 Maximum loading flexibility • Compatible with ceiling rail systems • Optionally with insert shelf system for small batches _____ ⚙️ Intelligent control – just the way you need it ✅ PID control (optional) for precise temperature control ✅ Touchscreen control panel & smartphone control 📱 (optional) ✅ Weekly & monthly reports at the touch of a button (optional) ✅ Timer function: freely programmable from 10 minutes to 24 hours ⏲️ ✅ Automatic shutdown after the end of the process _____ ♨️ Ramp heating mode (optional) Precisely control temperature progression and holding times, e.g. E.g.: Nedpowfgbrofx Afasla • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Request more information

Year of construction: 2003, condition: good (used), Weishaupt gas burner Monarch Burner type G7/1-D Version ZMD Power 300 - 1750 KW Including gas line ( gas fitting ) Nedpfx Afsmdpczeajla Burner was recently in operation

Year of construction: 2005, condition: excellent (used), Gas burner Weishaupt WM-G40/1B -Version ZM-LN Power 400-2100KW: year of construction: 2005 including gas line from Dungs DN50. Мы говорим по русски! Visits please only after telephone arrangement! Nodpfx Ajf Srcqofaela Preferred sale to dealers, tradesmen or export. All information without guarantee, errors and prior sale reserved. The seller is not liable for typing and data transmission errors. Gladly we take your used boiler or burner in purchase! Of course we also take care of all formalities Loading possible

Year of construction: 2001, condition: excellent (used), Weishaupt GL 30/2-A dual fuel burner -Version Z: Output 300-2150KW: year of construction:2001 Oil throughput 40-180 kg/h With existing fittings Dungs DN50 Мы говорим по русски! Visits please only after telephone arrangement! Preferred sale to dealers, tradesmen or export. All information without guarantee, errors and prior sale reserved. The seller is not liable for typing and data transmission errors. Gladly we take your used boiler or burner in purchase! Of course we also take care of all formalities Njdpsf Src Rsfx Afaela Loading possible

Condition: excellent (used), Weishaupt WM-L20/1a. 1400kw. 118kg/h year.2008 Nlsdeig Tw Nspfx Afaoa

Year of construction: 2006, condition: excellent (used), Oil burner Weishaupt oil burner GL7/1-D Year :2006 Njdpfx Aji Atc Hofajla Мы говорим по русски! Viewing please only after telephone agreement! Preferred sale to dealers, traders or export. All information without guarantee, errors and prior sale reserved. The seller assumes no liability for typing and data transmission errors. Gladly we take your used boiler or burner in purchase! Of course we also take care of all formalities Loading possible

Year of construction: 2006, condition: excellent (used), Dual fuel burner Weishaupt RGL7/1D -version ZMD Power 300-1750KW: Year:2006 Oil throughput 32-147 kg/h With existing fittings Dungs DN65 Shipping possible worldwide. Мы говорим по русски! Viewing please only after telephone agreement! Preferred sale to dealers, traders or export. All information without guarantee, errors and prior sale reserved. Nsdshl R T Nspfx Afasla The seller assumes no liability for typing and data transmission errors. Gladly we take your used boiler or burner in purchase! Of course we also take care of all formalities Loading possible