Used Widebelt Sanding Machine 3 Units for sale (109,264)

Condition: not inspected (used), Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance Gbedpet Tqy Ejfx Abgsn thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: new, Number of sanding units 4 St. sanding width 190 mm Sanding height max. 180 mm LÖWER-DoubleSander Solid DSM 2004 ----- Double-sided four-belt single wood sander for Sanding solid wood such as window frames etc. Highly stable top design with innovative details. Suitable for high continuous loads even with higher chip removals. - sanding units arranged one after the other for pre-grinding, Fine sanding and finishing sanding, each from above and below 1. Belt sanding unit with heavy steel roller 2. Belt sanding unit with rubberized roller and shoe 3. Finishing unit with fiber brush - Directly driven grinding rollers for slip-free Power transmission - maintenance and wear-free CERMET-coated grinding wheels shoes with very good thermal conductivity and absolute Dimensional accuracy - External cooling of the grinding zones for cooler grinding and longer sanding belt service life - force-guided pneumatically controlled sanding belt oscillation - effective sanding dust extraction directly on the Grinding rollers - Airborne dust extraction on the tension rollers - Integrated brushing and finishing device with large Grinding dust extraction - motorized grinding thickness adjustment via precision threaded spindles and large-sized linear ball screws bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of the chip removal at the bottom via precision Threaded spindle with dimension display via scale ring (Resolution 0.1mm) - Sanding belt tension via pneumatic cylinder constant clamping pressure - Sanding belt change with pneumatic belt relaxation Within seconds - Adjustment option for the sanding belt run Band change - electro-pneumatic compressed air monitoring - Anti-running protection via contact roller if it is too thick workpieces - Workpiece transport via calibrated non-slip and non-stick fixed conveyor belts over heavy, cast tables Finely planed surface and spring-loaded pressure rollers with fine adjustment - Cardan shaft drive for smooth and consistent Workpiece transport - Feed gear motor with stepless speed 4-20 m/min - all motors electrically protected - ergonomically arranged controls - digital thickness display (resolution 0.1mm) with modern Magnetic tape system Technical data: - Sanding belt speed 22 m/s - Sanding belt length 1800mm - Sanding belt width 200mm - Working width 190mm - Grinding thickness 2-180mm - four brake motors for 5.5 kW drive - Feed motor 1.5 kW - Feed speed 4-20 m/min. - automatic height adjustment 0.37 kW - two brush units with fiber brushes D 120 x 200mm at 0.37 kW - Suction nozzle 2 x 180mm 2 x 120mm - Extraction air speed 20 m/s - Pneumatic connection 6 bar - Working height 870mm - Length (with soft disc 2740mm) 2600mm - Length with control panel (with soft disc 3035mm) 2985mm - Width 880mm Godpfovnv Tqox Abgebn - Height 1910mm - Weight approx. 3300 kg - Operating voltage 400 volts, 50 Hz, 3P - CE version ----- Price of the above machine on request! ----- Special accessories with additional charge: Workpiece blow-off - using nozzles from above and below at the machine outlet arranged, pneumatically controlled 4-belt sanding belt blowout via nozzles directly on the radii of the tension rollers inside the suction arranged, timer controlled on/off 5 seconds each, can be switched on separately Di...

Condition: excellent (used), 3-axis machining center Work area: 1350 x 2565 mm. Gbedpszcpfajfx Abgsn

Condition: used, total length: 1,330 mm, total width: 1,040 mm, total height: 1,150 mm, Empty weight: 1.800 kg Price: On request - Documentation available: No - CE certificate present: No - Drive system: Conventional - Drive: Hydraulic - Vertical/Horizontal: Horizontal and vertical - Number of rolls [pcs.]: 3 - Number of driven rolls [pcs]: 3 - Shaft diameter [mm]: 75 - Top roll diameter [mm]: 225 - Capacity diameter round [mm]: 60 - Transport dimensions: 1330mm x 1040mm x 1150mm (l x w x h) - Transport weight [kg]: 1800kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Gedpfxexuf Sle Abgebn Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Used machine Gbedpfx Aeyncpijbgon Equipment: - Cutting length 2500 mm - With handwheel tensioning Availability: short-term Stock location: 63934 Röllbach

Condition: new, CATALOG NUMBER HL001 - New machine, in stock – Pre-milling unit – Radial scraper + polishers TECHNICAL DATA - Panel thickness: 45mm - Edge thickness: 0.4 mm – 3 mm - Min panel width: 90mm - Min panel length: 90mm - Feed speed: 7m/min - Pre-milling: 9000 rpm - Top/bottom: 10500 rpm - Front/back: 8800 rpm - Polishing: 2800 rpm - Main motor: 6kW - Feed power: 0.75kW - Pre-milling power: 1.5kW - Glue spindle power: 0.25kW - Top-bottom milling power: 0.18kW - Top milling power: 0.55kW - Top polishing motor: 3-phase 0.12 kW, 1-phase 0.18 kW - Bottom polishing motor: 3-phase 0.12 kW, 1-phase 0.18 kW - Working table height: 856mm, extended support width: 560mm - Extraction connection: 3x100mm - Dimensions (L/W/H): 3200/1200/1200mm, weight: 660kg Gjdpfezccuusx Abgobn Net price: 49,900 PLN Net price: 11,880 EUR based on 4.2 EUR exchange rate (Prices may change with significant fluctuations)

Condition: used, Roll sets for profile bending machine, 3-roller ring bending machine HERKULES WETZLAR The rollers are compatible with a HERKULES WETZLAR profile bending machine, type BO 238 N Gbsdoglaq Ispfx Abgen Shaft diameter: 60 mm with 18 mm keyway 2 pieces, roller set No. 1, roller diameter 110 mm, roller width = 180 mm 2 pieces, roller set No. 2, roller diameter 160 mm, roller width = 40 mm 3 pieces, roller set No. 3, roller diameter 150 mm, for tube diameter Ø 33 mm, roller width 87 / 115 mm - Roller set No. 3 with adapter ring from Ø 93 to Ø 60 mm, without keyway The machine had 2 driven rollers Weight of all rollers: 57 kg Good condition

Condition: used, Year of construction: 2000, Table size: 1340 x 800 mm + table extensions Gbedjzb N T Ijpfx Abgsn Table height: 870 mm Control panel at eye level Swivel range: -5 - 45° Aigner integral stop Spindle speeds: 3000 / 4500 / 6000 / 9000 1/min Vertical adjustment: 120 mm Milling arbor: 30 mm / MK 5 Dust extraction port: 2x 120 mm Weight: approx. 1000 kg Storage location: Supplier

Condition: used, Year of construction: 2001, controller manufacturer: Heidenhain, controller model: MillPlus, _____ Gedpfszbzchjx Abgsbn Description: Year of manuf. : 2001 Control : Heidenhain MillPlus Speed : 18000 rpm Movement X/Y/Z : 630/560/560 mm Tool holder : SK 40 Spindle: Technology:Motorspindle Speed:18.000 rpm Power (max.):35 kW Torque (max.):119 Nm Taper:SK40 Workingtable: Clamping surface:1.000 x 600 mm Tableloading (max.):400 kg In general: Toolmagazine:2x 10 stations Rapid travers in X/Y/Z:26/26/20 m/min Equipment/Accessory: Chipmanagement:Chiptrumpet Coolingmanagement:Cooling unit Oilmistseparation:Mechanical extraction, Hör AFS 1100 4.-Axis:Magerl Rotomatik 120 with Counterbearing Processobservation:Operation mode 4 Setup operations:Electronical handwheel Further Equipment:Spindlechiller, Rinsing pistol Further Accessory:Misc. used Toolholder SK 40

Condition: used, Year of construction: 1999, controller manufacturer: Heidenhain, controller model: MillPlus, _____ Description: Year of manuf. : 1999 Gbodpfx Abezbzcbjgjn Control : Heidenhain MillPlus Speed : 12000 rpm Movement X/Y/Z : 800/650/550 mm Spindle: Technology:Motorspindle Speed:12.000 rpm Power (max.):15 kW Torque (max.):130 Nm Taper:SK40 Workingtable: Clamping surface:1.100 x 650 mm Tableloading (max.):600 kg In general: Toolmagazine:25 stations Rapid travers in X/Y/Z:18/18/15 m/min Equipment/Accessory: Chipmanagement:Chip tray Coolingmanagement:Coolant pump Oilmistseparation:Electrostatic extraction, W+W EL-FI 1000 Further Equipment:Rinsing pistol Further Accessory:Misc. used Toolholder SK 40

Condition: excellent (used), Year of construction: 1993, Enorm edge sanding machine (now Kündig) In very good condition. Type: LBK 160 Year of manufacture: 1993 With veneer edge sanding attachment Oscillation can be switched on. Electric height adjustment of the sanding unit Table can be tilted up to 45 degrees Sanding belt width 150 mm Sanding belt length 2600 mm 3 kW motor 2 additional motors for height adjustment and oscillation With feed system Weight approx. 400 kg Location: in stock at 54634 Bitburg - immediately available - Gbjdpjzbyt Eefx Abgen

Condition: excellent (used), functionality: fully functional, input voltage: 230 V, year of last overhaul: 2026, total height: 1,120 mm, total length: 715 mm, total width: 2,210 mm, type of input current: AC, overall weight: 170 kg, control voltage: 24 V, DGUV certified until: 07/2027, Riehle RMBB Coating Machine 2 coating curtains Stainless steel design Simple technology For coating sheet metal with dimensions 580 x 780 mm Simple technology DGUV V3 tested – available only from us Gedpfxeyakk So Abgebn 230 V connection Used machine, cleaned and SAB inspected With warranty + spare parts service We have many other bakery machines in stock!

Condition: excellent (used), - Dimensions: 518x760x1420mm - Flavours: 2 and mixed Gsdpfx Abewxu Srjgjbn - Output: 17-18L/h - Voltage: 220V - Power: 1.7KW - Net weight: 143kg

Year of construction: 2002, condition: excellent (used), functionality: fully functional, ELUMATEC KF 178 – 3-Spindle Copying Router Technical Data Upper Routing Unit Routing area with stops or copying templates: 340 × 100 mm Stroke: 110 mm Lower Routing Unit Routing area with stops or copying templates: 240 × 85 mm Front stroke: 95 mm Rear stroke: 45 mm General Data Continuously adjustable speed from 3,000 to 12,000 rpm. Also suitable for thin-walled steel and stainless steel profiles. Clamping range for profiles: 115 × 100 mm Mains connection: 230/400 V, 3 ~, 50 Hz Motor power per spindle: 0.74 kW Compressed air connection: 7 bar Air consumption per working cycle: 12 l without spray device 24 l with spray device Gbjdpfx Abezcz Dnegon Dimensions (L × W × H): 980 × 1,250 × 1,610 mm Weight: 360 kg Equipment Ideal machine for economical door production. For routing lock cases, profile cylinders and rosettes in aluminum and PVC profiles. Three fully independently operating copying routing units. Separate control of the horizontal and vertical routing spindles. Workpiece clamping upwards against the lock assembly surface, eliminating the need for readjustment with different profile heights. “Spindle Lock” for quick tool changes. Flexible stop system with support rollers and adjustable folding stops. Profile cylinders and rosettes.

Condition: used, Year of construction: 1994, Max. passage height: 160 mm Sanding belt length, unit 1: 1900 mm Max. working width: 1350 mm Number of belts: 2 Gedpsy Naq Uefx Abgsbn Belt, unit 1: Calibrating roller, grooved, rubber design Unit 1: Steel, grooved Sanding belt width, unit 1: 1350 mm Unit 2: Combination sanding unit Design, unit 2: Roller/shoe Control: Manual control panel, electric/pneumatic Belt oscillation: pneumatic Infeed height: fixed (top section moves) Table stroke: electro-mechanical Table display: mechanical numerical display Working height or feed table height: 900 mm Location: Nattheim

Condition: ready for operation (used), Tool milling machine DECKEL FP 3 with Heidenhain digital display - Well-maintained, original condition - Travel ranges X/Y/Z 500x300x400 mm Gedpfx Aezcxtajbgobn - Feeds / rapid traverses in all 3 axes - Tool holder ISO 40 - Speed range 40 - 2000 rpm - Vertical / horizontal milling capability - Swivel table - Coolant system - Central lubrication - Chip tray - Documentation Dimensions: L x W x H 1.7 x 1.2 x 1.8 meters / Weight 1350 kg Errors and omissions excepted.

Condition: used, Year of construction: 1995, functionality: fully functional, grinding height: 100 mm, grinding length: 3,250 mm, We are offering this used Löffler KSL-100 MG edge sanding machine, year of manufacture 1995. Godpfeythu Ijx Abgsbn Manufacturer: Löffler Maschinenbau GmbH Langenaltheim / Bavaria Model: KSL-100 MG Serial number: 95.005/6/95 Year of manufacture: 1995 If you have any questions or require further information, please feel free to send us a message or give us a call.

Condition: good (used), Weinig EM 4 Gbodpfezcnwujx Abgon

Condition: new, Year of construction: 2025, Table milling machine minimax twf 55 es M 3 UP Professional workman's machine with motorized height and inclination adjustment of the milling spindle, four speeds and electronic control system Item number 5502266 Brand Holzkraft / SCM Gedpshp Rc Ijfx Abgobn EQUIPMENT Equipment Aluminum sliding carriage ✔ Handle at sliding carriage ✔ FLEX ONE routing fence: heavy-duty professional design, automatic adjustment of the entire routing fence depending on the tool diameter, manual adjustment of chip removal, swing-away device, aluminum fence jaws with connecting strips Height adjustment of the spindle motorized. Telescopic miter fence with two folding stops Inclination adjustment of the spindle motorized Cantilever table ✔ Ready 3 control: Programmed movement of the milling unit in two axes, Automatic adjustment of the entire milling stop depending on the tool diameter, Stepless adjustment via switch or automatic positioning system Curved milling protective hood ✔ Position of control elements Control panel at eye level, swiveling Eccentric clamp TECHNICAL DATA Dimensions and weights Length (product) approx. 1200mm Weight (net) approx. 510kg width/depth (product) approx. 2000mm Connection suction suction connection diameter 2 x 120mm Work table Working table length 1200mm Sliding carriage length 1200mm Working table width 530mm Sliding carriage width 360mm Table height 900mm Slide height 142mm Installation information Space requirement length 2800mm Machine body width/depth 846mm Space requirement width [...]

Condition: as good as new (ex-display), Year of construction: 2024, The robust Junior R1 offers all the features that a modern edge sanding machine must have. A solid cast iron sanding unit with a powerful powerful motor ensures maximum sanding performance. The working table, adjustable in height by spring pressure, allows optimum belt utilization and safe working. Belt oscillation, infinitely variable unit swiveling, and veneer unit, a veneer sanding device and an additional table for and an additional table for sanding work on the on the deflection roller. The machine is supplied with an assortment of sanding belts; an angle and miter fence is also included. Godpod R Ev Dofx Abgsbn Technical data: - Motor power: 2.2 kW - sanding belt size: 150 × 2280 mm - grinding belt speed: 22 m/sec. - table size: 750 × 350 mm - space requirement: 1000 × 800 mm - weight: from 180 kg - Suction Ø: 100 mm Location: Ex warehouse 54634 Bitburg - free loading - Can be shipped for a fee

Condition: as good as new (ex-display), Year of construction: 2026, 5222454 LIBRA 45/2 RTC 135 Wide Belt Sander 5257433 "Z" Designation for RTC 135 5257452 Vacuum table with electric fan 3 kW 5257453 Oscillating belt air-blast device for 5257454 Oscillating belt air-blast device for 5257462 Reinforced motor 15 kW (20 HP) 5257485 Roller table at infeed and outfeed for 5257499 Grooved rubber pressure roller, 2nd position Gbedpfx Abey Ehiwegon 5257500 Grooved rubber pressure roller, 3rd position 5257504 Infinitely variable conveyor feed with inverter 5257605 Door with inspection window 5257606 LED lamp for internal illumination TECHNICAL DATA Dimensions and Weights Length (product) approx. 1800 mm Width/depth (product) approx. 2000 mm Height (product) approx. 2070 mm Extraction Connection Number of extraction ports: 2 Extraction port diameter: 200 mm Electrical Data Feed motor power: 0.8 kW Connection voltage: 400 V Mains frequency: 50 Hz Height adjustment motor power: 0.25 kW Output power (motor power): 11 kW Sanding Unit Sanding belt length: 2150 mm Sanding belt width: 1370 mm Max. sanding width: 1350 mm Feed Unit Feed speed: 4.5 / 9 m/min Workpiece Min. workpiece height: 4 mm Max. workpiece height: 170 mm Product Information EU 2023/2854 Type of generated data: usage data Format of generated data: common, machine-readable formats, e.g., JSON Data volume: up to 5 MB Continuous real-time data generation: yes Data storage location: on the device and a remote server Data access: on the device and via physical and wireless interfaces Location: ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2024, The Uniq series is the full-fledged basis of our range and shares all the features that have helped the Kündig edge sanding machine gain its reputation on the market as a robust, versatile precision instrument. Part of its extremely solid construction is the motorized oscillating sanding unit, which offers a maximum oscillation travel of 90mm and the possibility of motorized tilting by up to 45°. All the usual edge processing operations can be carried out at the up to four grinding stations. Edge sanding machine Kündig Uniq front and rear side Ingenious design - the sanding unit The heart of all our edge sanding machines is the sanding unit. It offers a whole range of intelligent functions and features. For example, the sanding belt does not oscillate by tilting the belt rollers. Instead, the entire sanding unit moves up and down. The oscillation stroke, as well as the oscillation range, are easily set by pressing a button. Thanks to the flexible adjustment and the large oscillation travel, sanding belts can be used optimally over their entire width, without the need for laborious adjustment of the worktable height. The oscillation mechanism is driven by a separate motor. Gsdpfx Abofig Rwogobn The sanding unit can also be tilted conveniently by means of a rotary switch and also with the aid of a separate motor. The unit can be tilted between 90° and 45°. Thanks to the sophisticated swivel mechanism

Condition: new, Year of construction: 2026, Heavy machine base guarantees high torsional rigidity and vibration-free operation Better sanding results due to sanding belt oscillation via separate gear motor Oscillation optionally switchable Veneer edge sanding device with fine adjustment as standard Grooved infeed ruler for sanding veneer overhangs Quick changeover from veneer to solid wood sanding Gbsdpfx Abjff Ed Tsgjn Height-adjustable sanding table for utilization of the entire sanding belt width Height adjustment of the sanding table and sanding unit swivelling via hand wheels Height-adjustable additional table with suction device for grinding radii Optimum chip removal through extraction at the unit and at the cross table Automatic compensation of strip length differences due to spring-loaded strip tension Dimensions and weights Length approx. 1900 mm width/depth approx. 810 mm Height approx. 1230 mm Weight approx. 290 kg Dust extraction connection Suction socket diameter 120 mm Drive power Oscillating motor 0,25 kW Work table(s) Working table length 960 mm Working table width 352 mm Working table height adjustment 210 mm Cross table height min. 730 mm Electrical data Input power 3 kW Supply voltage 400 V Phase(s) 3 Ph Current type AC Mains frequency 50 Hz Sanding unit Sanding belt length 3000 mm Sanding belt width 150 mm Belt speed(s) 20 m/s grinding surface length 1050 mm Grinding surface width 220 mm Swivel 0 - 45 ° Oscillation stroke 20 mm Availability: Short term

Condition: new, Year of construction: 2025, Designed for professional structuring and grinding work Motorised height adjustment of the working units with digital display Aggregates can be switched on individually Highly resistant rubberized conveyor belt Stepless feed Inlet height constant Models str l with infinitely variable, inverter-controlled brush speed: this enables the speed to be precisely adapted to the material, making them particularly suitable for sensitive materials. Unit for saw cut optics optionally available Motor-driven height adjustment of the units Gbjdpfx Aeff Hdgobgon Aggregates can be switched on individually feed infinitely variable Dimensions and weights Length approx. 1300 mm width/depth approx. 1000 mm Height approx. 1300 mm Weight approx. 440 kg Dust extraction connection Suction nozzle diameter 2 x 150 mm Brushes diameter 190 mm length 300 mm revolution 1500 min-¹ Electrical data Drive motor power 2 x 3.0 kW Power feed motor 0,22 kW Input power 6,25 kW Supply voltage 400 V Phase(s) 3 Ph Current type AC Mains frequency 50 Hz Noise emission Sound power level Lw (idling without extraction) 65 dB(A) Sanding unit grinding width max. 300 mm Feed unit Feed speed 1 - 13 m/min Workpiece Height max. 300 mm Weight max. 100 kg

Condition: new, Year of construction: 2024, Holzkraft edge sanding machine Type: KSO 200 F with veneer sanding device Sanding unit can be swivelled up to 45° by means of a lever Machine stand made of welded steel guarantees high torsional stiffness and vibration-free operation. Oscillating sanding belt with separate gear motor for better sanding results Oscillation optionally switchable Sanding soleplate with graphite coating for a longer service life of the sanding belt Height-adjustable sanding table for utilization of the entire sanding belt width Height-adjustable additional table with suction for grinding radii Spring-loaded belt tension automatically compensates for belt length differences. With double suction Extendable roller table extension With rubberized sanding roller Veneer edge sanding device with contact shoe with fine adjustment, relief rollers and stop rulers With grooved infeed ruler for veneer overhangs Quick changeover from veneer edge sanding to solid wood sanding possible Dimensions and weights Length approx. 1900 mm Width/depth approx. 900 mm Height approx. 1350 mm Weight approx. 290 kg Connection dust extraction suction nozzle diameter 140 / 100 mm Drive power oscillation motor 0,25 kW Working table(s) working table length 960 mm working table width 350 mm Gedpfx Abolht H Njgsbn Working table height adjustment 230 mm Height min. 735 mm Height max. 965 mm Height adjustment longitudinal table 230 mm Cross table length 330 mm Cross table width 330 mm Cross table height min. 720 mm Cross table height max. 900 mm Cross table height adjustment 180 mm Electrical data Power drive motor 3,0 kW Supply voltage 400 V Grinding unit grinding belt length 3000 mm grinding belt width 200 mm Belt speed(s) 20 m/s Grinding surface length 1050 mm grinding surface width 200 mm Oscillation stroke 20 mm Location: Ex stock 54634 Bitburg - immediately available -