Used Holder Narrow-Gauge Tractor for sale (15,093)

Condition: new, maximum load weight: 45,250 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. The following is an excerpt of the equipment. Complete equipment details are available upon request. Chassis, gooseneck: Special steel frame made of high-strength fine-grained steels, electrically welded at the connection points, well-dimensioned outer frame. 4-axle arrangement. Wheel arches above the axles with spray mist suppression. All steel parts are sandblasted. Lateral impact protection made of anodized aluminum installed. Increased point load of approximately 30,000 kg over approximately 4,000 mm. Special design in the gooseneck area for maximum low-bed length in combination with AluLeg support legs instead of telescopic support winches, maximum rear swivel radius of the tractor unit approximately 2,100 mm. Special superstructure with rear beam widening: DINKEL – special superstructure. Self-supporting aluminum roof beam/profile approximately 120 x 100 mm, sliding cover with plastic flaps. Rear beams can be widened to approximately 4,200 mm (only for loading and unloading). Three sliding beams per side with rubber strap relief. Additional center beam locking mechanisms in the roof beam and parking position, using a pull cable and spring latch. DINKEL – lifting roof mechanically height-adjustable. Lifting roof height approximately 400 mm, operable on both or one side, without opening the opposite side and the doors. Additional height adjustment of approximately 480 mm in approximately 40 mm increments with height adjustment in the beams. Front overhang on the front wall for operation under a tarpaulin up to a total height of approximately 4,400 mm. Four rows of stackable approximately 150 mm aluminum slats on the sides, with 450 mm pockets at the bottom and 4 rows of single pockets above. In the upper bed, only 3 rows of insertable slats. Spacing between slats evenly distributed. Floor: Approximately 27 mm special water-resistant glued beech plywood, rough surface. Steel sheet in the wheel arch area. Forklift drivable according to DIN standard. Outer frame flush with the surface. Brakes: WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (parking release safety valve). Spring-loaded brake cylinders as parking brake. Wabco Smart Board with odometer and unit load indicator. Includes WABCO tire pressure monitoring system. Axles: 4 x 10,000 kg SAF/Sauer with drum brakes in low-bed design. Air suspension with lifting and lowering device, total lift approximately 230 mm. Third and fourth axles as friction-jointed trailing axles with electrical and mechanical lock. Twin tires: 235/75 R 17.5, -16-ply. Manufacturer of our choice, including E-wheel holder. Without E-wheel. Lighting: according to EC standard including side lights in LED design. Position lights in LED design. 2 additional reversing lights. 2 work lights on the front wall inside, at the top. Painting: Chassis and superstructure in a single color in the RAL color of your choice. Center beams, axles coated with KTL (cathodic electrodeposition) in black. Corner beams in hot-dip galvanized design. Plastic parts in black. Hot-dip galvanized parts unpainted. Rims in factory silver. Special equipment included: - E-supply cable 15-pin - Air suspension in ECAS design, operated on the semi-trailer - Overwidth signage at the front and rear in zinc-plated, continuously telescopic design with attached boundary lights including so Iisdpfx Ajz Dmn Ropcjg

Condition: repair required (used), functionality: limited functionality, power: 49 kW (66.62 HP), first registration: 07/2011, fuel type: diesel, color: orange, fuel: diesel, Year of construction: 2011, Equipment: air conditioning, all wheel drive, car registration, cruise control, differential lock, hydraulics, Holder C 270 Drive System 4-cylinder, 4-stroke Kubota diesel engine, Type 2607, 49.2 kW / 67 hp in the C 270 Hydrostatic all-wheel drive via four equal-sized wheels Infinitely variable speed selection with a total of four pre-selectable gear stages Hydraulic wheel load compensation (combined independently and dependently) Mechanical differential lock, front and rear, simultaneously switchable electrohydraulically Hydraulic service brake and electric parking brake as a drum brake Suspended front and rear axles Cab including heater Heat-protective glazing and sliding side windows Multi-function display (tachometer, operating hour meter, speed indicator, remote thermometer for engine and hydraulic oil, fuel level indicator) Mechanically adjustable steering column 3 storage compartments, sunshade film, interior cab light with door contact switch Hydraulics Multi-function arm console with driving program and differential lock switch Hydrostatic articulated steering with 2 double-acting steering cylinders Additional Equipment Mounting frame for tool-free changing of platforms and attachments Locking rail at the front for adjusting the top link Electrical system: AC generator 12 V / 90 A – 1080 W Battery 12 V / 88 Ah Battery disconnect switch Radio preparation: wiring harness, antenna, speaker grilles Lighting system according to StVZO (German Road Traffic Licensing Regulations) 7-pin socket at the rear Path signal prepared via Super-Seal plug connector Biodegradable hydraulic oil Stainless steel support pad Standard paint color: Orange RAL 2004 Front linkage Front linkage incl. safety hook CAT IN / CAT I with passive tilt adjustment Iisdpfozfbu Rex Apceg Rotating beacon Locking block Mechanical PTO shaft, front 1000 rpm at the front Hydraulic flow divider 1 Flow divider, 1st circuit adjustable from 0–25 l/min with line set to the front and rear Return line at the front and rear Hydraulic kit, attachment adjustment pump Attachment adjustment pump 0–80 l/min, variable Line set to the front and rear Return line at the front and rear Leakage oil line at the front and rear Hydraulic tilting device for superstructure arms Hydraulic set 2 3 double-acting control valves 2 with floating position 4 quick-release couplings 2 quick-release couplings at the rear, angled connected via a T-piece with quick-release couplings at the front Active hydraulic tilt adjustment 1 joystick incl. direction of travel switch and speed control Electro-hydraulic attachment relief Comfort package Driver's seat with air suspension, armrest 2 work lights at the front 2 work lights at the rear WITH THE FOLLOWING DAMAGES: - Articulated joint worn out - Age-related and usage-related wear on the vehicle - Rust damage corresponding to the age Changes, typing errors, mistakes and prior sale are subject to change. All information is provided without guarantee. The sale is made with the exclusion of any warranty or guarantee.

Condition: ready for operation (used), Year of construction: 2007, pressing force: 28 t, stroke length: 200 mm, throat depth: 200 mm, installation height: 325 mm, working length: 835 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Press force: 28 t Bending length: 835 mm Travel range of the back gauge: 0 – 370 mm Stroke: 200 mm Iijdozzkwgepfx Apcjg Distance between frames: 890 mm Support table: 200 x 275 mm Overhang: 200 mm Installation height: 325 mm Number of cylinders: 1 Working speed Press travel: 8-10 mm/s Retraction: max. 35 mm/s Positioning accuracy: +/- 0.05 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 1,600 x 1,500 x 2,200 mm Total weight: 3,500 kg EQUIPMENT Operating manual Safety device Mechanical tool clamping (top) The height and weight of the asset must be taken into account when selecting the transport vehicle. A forklift is available for loading. If the asset is not collected on time, a storage fee of €20.00 per lot and per day (or part thereof) will be charged. The fee must be paid before collection. The sale is made without any warranty or guarantee. The information on the technical data comes from the original offer. No guarantee is given for typographical or measurement errors. If in doubt, please compare the information with the photos provided or inspect the goods on-site before the end of the auction.

Condition: used, mileage: 999 km, power: 26 kW (35.35 HP), first registration: 06/1991, fuel type: diesel, empty load weight: 1,365 kg, maximum load weight: 635 kg, overall weight: 2,000 kg, axle configuration: 2 axles, color: orange, gearing type: mechanical, suspension: other, number of seats: 1, total length: 3,000 mm, operating hours: 4,911 h, Non-binding offer - Subject to alterations and prior sale - Sale is subject to exclusion of any warranty - All information without guarantee! Iedpfx Apsz A Afcocjig

Condition: used, For sale is a high-quality TESA Micro-Hite 3D height gauge in a large, motorized version, offered as a complete measuring workstation. This system combines precise height measurement with extended 2D/3D coordinate functions, making it ideal for use in quality assurance, metrology, and production. Particularly noteworthy is the extensive range of accessories and the existing PC connection with printing capability, which allows measurement reports to be created and documented directly. Technical specifications: Manufacturer: TESA (Switzerland) Model: Micro-Hite 3D Type: Height gauge / 3D-capable measuring column Measuring range: approx. 600 mm (large version) Resolution: up to 0.0001 mm (0.1 µm) Ijdpfoy Tkg Ujx Apcjig Drive: motorized adjustment Measuring system: digital / electronic Data output: interfaces for PC / peripherals Measuring functions: Height measurement Internal and external measurement Diameter measurement Distance measurement 2D/3D point measurement Geometry and position calculations Equipment: Granite measuring plate Stable machine base Motorized measuring column Integrated control unit External PC workstation (monitor, computer, input devices) Printer for report output Accessories: Extensive set of measuring probes (ruby tips, extensions, etc.) Tool holders and fixtures Accessory case / wooden box The measuring device has already been disassembled and packed.

Condition: like new (used), Year of construction: 2025, operating hours: 650 h, functionality: fully functional, total height: 2,274 mm, total length: 3,061 mm, total width: 2,129 mm, feed length X-axis: 15,000 mm, feed length Y-axis: 15,000 mm, feed length Z-axis: 15,000 mm, type of input current: three-phase, grinding wheel diameter: 150 mm, overall weight: 3,300 kg, rotational speed (max.): 10,500 rpm, travel distance X-axis: 320 mm, travel distance Y-axis: 200 mm, travel distance Z-axis: 470 mm, input current: 30 A, input frequency: 50 Hz, input voltage: 400 V, space requirement width: 3,000 mm, space requirement length: 4,000 mm, space requirement height: 3,000 mm, Equipment: rotational speed infinitely variable, WALTER CNC Grinding Machine HELITRONIC MINI PLUS (RAPID version) GE Fanuc Series 31i - B5 2025 650 working house. please see all information in attached PDF file * Machine Type: WALTER CNC Grinding Machine HELITRONIC MINI PLUS (RAPID version) * Fire extinguishing system DIMES * Holder for sharpening stones * Tool gripper * Protective and cleaning arbor * Plug gauge * Setting disc * Pull stud * Clamping arbor for hobs (diameter 32 mm) * Clamping arbor for hobs (diameter 40 mm) * Foot operated switch * Keyboard shelf * Standard grinding wheel adaptor (HSK50 form A, d20, D50, L55, L1=25 mm) * Standard grinding wheel adaptor (HSK50 form A, d20, D50, L55, L1=45 mm) * Standard grinding wheel adaptor (HSK50 form A, d20, D50, L55, L1=85 mm) * Dynamometric Key / torque wrench * Dynamometric Key Isdpfeztti Aox Apcsig * Mounting wrench * Sensor * Coolant unit Location in Israel . ready for inspaction . need export license

Condition: new, power: 353 kW (479.95 HP), fuel type: diesel, tire size: 315/80R22.5 R, axle configuration: 4x2, wheelbase: 3,800 mm, fuel: diesel, fuel tank capacity: 160 l, color: white, emission class: euro5, Year of construction: 2023, Equipment: fridge, spoiler, = Additional options and accessories = - Immobiliser - Spare wheel - Spoilers - Sun visor = Remarks = Cabin type: Active Space Country of origin: Spain Displacement: 11,000cc Gcw: 44 Tons Dimension: 6,250 x 2,550 x 3,783 Ground clearance: 217 mm Steering: LH Construction: Tractor Head Gearbox type: TX-12M LIMITATION ON SL INFOTAINMENT ECOSWITCH PORTABLE SMOKING KIT FMS DATA INTERFACE AUTO A/C+LER JOST FIFTH WHEEL 220AH H PERF REVERSE BUZZER L-3-P NET U-COMF ROCKING MODE FULL LED HEADLAMPS 7+7 PIN TRAILER PLUG FRONT PARKING BRAKE WITH BUNK CURTAINS 120A SMART ALTERNAT INDEP. C/E HEATER 6k STD GVW EQUIPMENT STANDARD AIR SUSP. SETTING TRAILER COUPL. - 2 LINE BRAKES STEEL WHEELS GREY IC444 CHASSIS SPEED LIMITER 90 KM/H DRIVE T. 315/80R22,5 SIDE MARKER LIGHT FRONT CORNER FINS JACK T INF HOSE PRES GAUG CAB AIR SUSPENSION UREA TANK 50 LITRES STANDARD AIRTANK PLATING STANDARD GEAR MODE 08329 SENZA ENG ID CUTOFF STD GREY PLAST. PART AS HIGH ROOF CAB FABRIC AIR SUSP. HEATED DRIVER LOWER EXHAUST PIPE STD SETTING C11/C13 FRONT ANTI-ROLL BAR FRONT UNDERRUN PROTECTION REAR ANTI-ROLL BAR 12TX 2420 TD GEARBOX HILL HOLDER REAR OVERHANG 1047,5 Ijdpfxsy Tymqj Apcoig LOADS 7500-13000Kgs MECHANICAL BATTERY SWITCH 4-DIN UPPER SHELF FABRIC STA. 2 WAY ADJ. PASS ESP DIGITAL AXLE WEIGHT INDICATION AEBS Compliant FOGLIGHT CORNER+BEND MPH/KPH SPEEDOMETER WARNING TRIANGLE SUB-ARTIC PACK -30 ANTI-SIPHON 2 TANK AIR INTAKE DUSTY ENV FIRE EXTINGUISHER PROVISION HEATED ELECTRIC REAR MIRRORS High Efficiency A-PI RUSSIAN OMOLOGATION PLATE 5th W H=150 MP=50mm ROOF INSUL SUB-ARTIC BATTERY CHARGE LAMIN FUEL TANK 1160L ALUMINUM 1 UND FLOOR STORAGE ENGINE PLATE REAR AXLE RATIO 2.85 REAR AIR SUSPENSION ELECTRIC ROOF HATCH STANDARD CAB TRIM SOFT TOUCH FOAM STEERING WHEEL TRATTAM. PROT. STD VIN CODE CHECK DIGIT CURTAINS ON DOOR WINDOWS FUEL TANK HEATER WITHOUT STICK79239 (IT03-EN) FIRST AID KIT 352CC AIR COMPRESSOR STEEL AIR TANKS APU FREE DISCHARGE HORIZ BATT SIDE FRAM MANUAL CAB TILT STANDARD REVERSE VERTICAL AIR FILTER ENG RPM = 1900 REV/ 5th W EC POSI06139 FRONT PARABOLIC SUSP REAR DAMPERS FILTER HP TRA/HEATED ECO-ROLL ELECTRIC HORN BULB REAR LIGHTS EMISSION EURO V W/O AMBIENCE LIGHTIN STANDARD CATWALK Radice VIN WJM = More information = Tyre size: 315/80R22.5 R Number of cylinders: 6

Condition: used, functionality: fully functional, power: 194 kW (263.77 HP), fuel type: diesel, operation weight: 30,620 kg, drive condition: 75 %, Year of construction: 2022, operating hours: 3,656 h, Equipment: UVV, cabin, Hyundai, Crawler Excavator, HX300ANL Year of manufacture: 2022 Operating hours: approx. 3650 ENGINE Cummins B6.7 / STAGE V Engine power: 260 hp (194 kW) at 2200 rpm. HYDRAULIC SYSTEM ELECTRIC POSITIVE FLOW CONTROL (EPFC) 3 Power modes, 2 work modes, user mode Variable power control Pump flow rate control Flow rate control for attachment mode Automatic engine idling Electronic fan control CABIN AND INTERIOR CABIN ACCORDING TO ISO STANDARD Top-mounted windshield wiper Radio/USB player Hands-free mobile phone system with USB 12-V socket (voltage converter 24 VDC to 12 VDC) Electric horn All-weather steel cabin with 360° panoramic view Safety glass, tempered Windshield as a sliding window Sliding glass window (left) Lockable door Heating and cooling box Storage compartment Transparent cabin roof cover Sun visor Door and cabin locks, one key Pre-control pressure-supported joystick Height-adjustable console system AUTOMATIC CLIMATE CONTROL Air conditioning and heating Defroster Cold weather starting aid (intake air preheating) CENTRAL MONITORING 8" LCD display Engine speed indicator or odometer/accelerometer Engine coolant temperature indicator Automatic power boost function Creep/travel mode Automatic idling Overload warning device Connected engine diagnostics Air filter monitoring Eco indicators Fuel level indicator DEF level gauge Hydraulic oil temperature gauge Fuel preheater Clock SEAT Mechanically sprung, heated driver's seat CABIN WITH ROPS ROPS (Roll-Over Protective Structure) ISO 1211 7-2 SAFETY Main battery switch Rear view camera Four work lights front (2 on boom, 2 on front frame) Driving alarm Automatic swing brake Boom holding system Stick holding system Safety valve for boom cylinder with overload warning device Three exterior mirrors OTHER Removable radiator dust screen for cleaning Removable storage container Fuel preheater Fuel prefilter Self-diagnosis system Hi MATE (Remote Management System) Batteries (2 x 12 V × 100 Ah) Double-acting line set (grapple, etc.) Accumulator for lowering attachments UNDERCARRIAGE Lower frame cover (standard) Bottom plates Triple-grouter bottom plates (600 mm) Track roller guides, 2 each Boom 6250 mm Boom safety valves Stick 3050 mm Stick safety valve Counterweight 5100 kg With bucket linkage Upper carriage for mono boom 2-way lines for hydraulic hammer and grapple, proportional Proportional lines for swivel function Lines for quick coupler Long tracks, narrow frame Track chains 600 mm (3-grouter plate) 20 mm 43-link Long track guide Std. lower frame plates Proportional joystick Air-suspended, heated seat SmartKey + Start/Stop button + Auto-Shutdown Radio and USB Rain protection Fuel filling pump Standard paint finish Standard guard rails Work light front on the cabin (LED) Work light rear LED With work light on the boom (LED) All-Around View Monitoring (AAVM) Driving alarm Standard frame Laminated 7 mm window glass Fuel preheater Central lubrication Beka (Europe) Biodegradable oil Panolin - synt 46 Cyclone air prefilter Isdpfxjzdqrpo Apcjig With quick coupler With 1 bucket

Condition: used, Year of construction: 2011, functionality: fully functional, machine/vehicle number: 102821, Technical characteristics: Work Area - Maximum diameter of the clamping plate: 250 mm - Maximum turning diameter: 270 mm - Maximum machining diameter: 220 mm - Maximum workpiece length: 175 mm - X-axis travel: 660 mm / Rapid traverse in X: 60 m/min - Z-axis travel: 300 mm / Rapid traverse in Z: 30 m/min - Standard closed automation (number of loading nests by workpiece diameter: 14/(80...200), 18/(30...160), 30/(30...85)) Main Spindle - Spindle interface to DIN 55026: Size 6 - Maximum speed: 4,500 rpm - Power at 100% / 40% duty cycle: 18 / 27 kW - Torque at 100% / 40% duty cycle: 202 / 303 Nm Tool Turret with Driven Tools - Toolholders, cylindrical shank DIN 69880: 12x VDI40 - Number of stations: 12 - Maximum tool length including holder: 190 mm - Maximum speed: 6,000 rpm - Maximum torque at 10% duty cycle: 37 Nm, 25%: 26 Nm, 100%: 14 Nm Iiedpfxoxxikgj Apcog Electrical Equipment - Operating voltage: 400 V - Connected load: 36 kW / 80 A Dimensions - Dimensions (L x W x H): 3,120 mm (4,185 mm with chip conveyor) x 2,266 mm x 3,200 mm - Weight: 7,500 kg Main Features and Capabilities: - Vertical design for optimal chip removal and easy access for loading/unloading - CNC control: GE Fanuc Series 32i Model A - High precision with X, Z, and Y axis positioning accuracy ±0.001 mm (Heidenhain linear scales) - Powerful main spindle with wide speed range - Integrated automation for part loading/unloading - Driven tools available for both milling and drilling operations - Workpiece detection sensor with compressed air gauge through spindle: SMW Autoblock Linear Position Sensor LPS-X - In-process gauging: Marposs T25 - Chip conveyor included - Documentation: Complete, both electronic and paper versions Machine status: IN OPERATION

Condition: used, gauge block box, gauge blocks, gauge block holder, parallel support, parallel support pair, plane-parallel measuring leg -Manufacturer: Koba, parallel gauge block set -Gauge block holder: 0-200 -Gauge block set: not complete, see photos for contents Iisdpfxeu H R D Es Apcog -Dimensions case: 545/210/H45 mm -Weight: 5.0 kg

Condition: ready for operation (used), Year of construction: 2016, operating hours: 23,500 h, functionality: fully functional, machine/vehicle number: 8107000021B, spindle bore: 32 mm, spindle speed (max.): 8,500 rpm, overall weight: 4,300 kg, controller model: FANUC 32i MB, bar length: 3,200 mm, DMG MORI GILDEMEISTER SPRINT 32/5 – Short/Long Turning Automaton Well-maintained machine, low operating hours, including IEMCA BOSS 338/32 HD bar feeder (up to 3,200 mm bar length), year of manufacture 2016, as well as a conversion kit to a long turning automaton (Swisstype kit) for short and long turning on a single machine. Delivery terms: Free on truck Availability: Immediate - subject to agreement NOTE: The machine must be picked up on a fixed date in mid/late October 2026; we will provide the exact date in advance! Technical data: Control: FANUC 32i MB Operating hours recorded: 25,263 Spindle hours recorded: 22,772 MAIN SPINDLE DATA: Max. turning diameter: 32 mm (guide bushing bore: 38 mm) Stroke Z1: 100 mm Max. speed: 8,500 RPM Drive power S1: 5.5 kW TAILSTOCK SPINDLE DATA: Max. turning diameter: 32 mm (guide bushing bore: 38 mm) Stroke Z2: 200 mm Max. speed: 8,500 RPM Drive power S1: 2.2 kW AXIS DATA X1: Travel: 70 mm Max. speed: 40 m/min Max. acceleration: 5 m/s² AXIS DATA Y1: Travel: 405 mm Max. speed: 30 m/min Max. acceleration: 5 m/s² AXIS DATA X2: Travel: 300 mm Max. speed: 40 m/min Max. acceleration: 5 m/s² TOOL HOLDER DATA – SLIDE 1: Tool holder diameter: 25 mm Number of fixed tools for external machining: 6 Tool holder size: 16 × 16 mm Number of driven tools: 4 Collet type: ESX20 TOOL HOLDER DATA – SLIDE 2: Number of fixed tools for internal machining: 4 Tool holder diameter: 25 mm Scope of delivery: IEMCA BOSS 338/32 HD bar feeder (up to 3,200 mm bar length), year of manufacture 2016 Chip conveyor Iijdpfez A Tbuex Apcjg Available manuals Accessories as shown in the pictures Dimensions & Weight Footprint (L x W x H): approx. 7500 x 1600 x 2500 mm Weight: approx. 4300 kg Attention: Disc damaged! If you have any questions or would like to arrange a viewing, please do not hesitate to contact us! Additional notes: ► Upon request, we can offer transport to your destination. ► The goods are sold without any warranty. ► Technical data is subject to change.

Condition: excellent (used), functionality: fully functional, first registration: 10/2025, fuel type: diesel, color: orange, fuel: diesel, operating hours: 255 h, Equipment: air conditioning, all wheel drive, car registration, cruise control, differential lock, hydraulics, trailer coupling, HOLDER C55SC DEMO UNIT with the following features: Work Package 1 Front linkage, 3D, double-acting incl. safety hook CAT II / CAT I Top link slider and top link with passive tilt adjustment and vibration damping (accumulator) for front-mounted implements Active hydraulic tilt adjustment for tilt adjustment Electro-hydraulic implement relief Rest bracket required for drawbar, rear linkage Electro-hydraulic implement relief Rest bracket PTO shaft, mechanical, front 1000 rpm Flow control valve 1 Flow control valve, circuit 1, adjustable from 0-35 l/min Implement adjustment pump variable, line set to the front and rear return and leak oil line to the front and rear Hydraulic kit 2 - 1 multi-function joystick (large joystick) incl. direction switch and speed control - 3 double-acting control valves, 2 with floating position - 6 front quick couplings - 2 rear quick couplings, looped, connected to the front quick couplings via a T-piece Tire 31x13.5-15 Wide-track fender kit Comfort Package Air conditioning, driver's seat with air suspension incl. seat heating, left armrest WORK LIGHTS, FRONT Cabin, center-mounted Overall height reduced by 40 mm Hydraulic tilting device 7-pin socket, front for implement lighting Reinforced wheel load equalization Manual central lubrication system Iijdpfxjzd Dzdj Apcsg Hydraulic tilting device for superstructure frame, incl. control valve Heated exterior mirrors with bracket + switch Hydraulic oil level warning system Work lights, rear Subject to changes, typographical errors, errors and prior sale. All information is provided without guarantee. The sale is made excluding any warranty or guarantee.

Condition: new, maximum load weight: 29,600 kg, overall weight: 36,000 kg, axle configuration: 3 axles, loading space volume: 32 m³, total width: 2,550 mm, total height: 3,600 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer stainless steel tank trailer for bitumen 32m³ TECHNICAL INFORMATION: * Vehicle code K.STS 32 / 1 - 10 / 24 * ADR suitable for the transport of dangerous goods * ADR tank code ADR tank code L4BH * Tank diameter 2,000 mm * External length 11,250 mm * Height 3,600 mm * Axle distance (Wb) 6,300 mm * Axle distance (A) 1,310 mm * Rear overhang 3,580 mm * Fifth wheel height 1,220 mm TECHNICAL CAPACITY: * Volume 32.0 m3 * Empty weight ±%3 6,400 kg Iisdor I S H Espfx Apcjg * Axle load 27,000 kg * King pin capacity 12,000 kg * The operating temperature is 250 °C * Test pressure (+H bar) 4.0 bar * The operating pressure is 2.0 bar * Total weight 39,000 kg TANK: * Cylindrical tank container with a slope to prevent residual quantities in the tank, made of AISI 321 (DIN 1.4541) stainless steel with ADR code L4BH * Vacuum valve The operating pressure is 0.21 bar * 1 x thermometer is included * Number of chambers 1 compartment * Insulation thickness The container is insulated with 100 mm thick glass wool * Insulation lamination Aluminum coating, CTP bomb * Final bottom coating The insulation on the front and rear bottom of the tank is coated with glass fiber reinforced polyester (GRP) * Stainless steel insulation rings fitted on the entire tank container * Number of manholes 1 pc. * 2" side air line made of aluminum on the right side of the vehicle. 2" TW coupling air line is included at the rear. * 1 x pressure gauge is included on the side air line * Equipped with a 1.5" air line for a higher delivery rate for bitumen and * to free the hoses from residues of the transported goods after unloading * 2" upper air line with 2-way sliding valve made of stainless steel * Aluminium walkway on the dome area * Mechanically foldable fall protection on the walkway in accordance with UVV * Access ladder on the right side of the container * The filling dome is on the front of the tank * There are 4 baffles in the tank DRAIN SYSTEM: * There is a DN100 bottom valve with handwheel operation on the discharge line, in accordance with the EN 14433 standard for dangerous goods. * Outlet line According to standard EN14433, outlet line starts with 4" bottom valve with handwheel control and leads to a 2nd safety valve for safe unloading (according to standard EN14432, 4" butterfly valve with mechanical control) and ends with a 3" TW coupling with internal thread and blind cover. A 1/2" sampling tap is included between the butterfly valve and TW coupling. * 1 x 6 m hose holder in an open-top box made of aluminum CHASSIS: * BPW axle with air suspension and disc brake and 3 x 9 tonnes permissible load capacity * BPW axles with 22.5" disc brake * Lift axle system on the 1st axle works automatically * KNORR-ILVL electronic air suspension ECAS * Tire size 385/65 R 22.5" 6-way * ALUMINUM rims * 1 x work light on the tank * Jost supports * 1 x plastic tool box, 400x480x600 mm OTHER: * ADR - Signum brand plate made of stainless steel, with a set of interchangeable numbers and foldable design * Danger sign in rigid design * Danger sign no: 3 * Danger sign no: 9 * Temperature sign * Environmental protection sign * 2 x fire extinguisher box without Fire extinguisher COLORS: * Chassis color RAL 3002 carmine red * Container color RAL 9006 white aluminum + paint We are happy to provide you with further information

Condition: ready for operation (used), Year of construction: 1997, operating hours: 13,465 h, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 400 mm, table load: 1,000 kg, controller model: Heidenhain iTNC 430, TECHNICAL DETAILS Travel range, X-axis: 600 mm Travel range, Y-axis: 450 mm Travel range, Z-axis: 400 mm Table load: max. 1,000 kg Tool holder: SK 40 MACHINE DETAILS Control system: Heidenhain iTNC 430 Operating voltage: 400 V Control voltage: 24 V Ijdezwmx Sspfx Apceig Machine weight: approx. 6,000 kg Operating hours: 48,690 h Spindle hours: 13,465 h EQUIPMENT Tool holders SK 40 Documentation Heidenhain programming manual Machine vise Clamping jaws

Condition: new, power: 349 kW (474.51 HP), tire size: 13R22.5, axle configuration: 6x6, wheelbase: 3,800 mm, fuel tank capacity: 390 l, color: white, driver cabin: sleeper cab, gearing type: automatic, emission class: euro3, suspension: steel, Year of construction: 2026, - 1 fuel tank IVECO T-WAY AT720T47WT H 6x6 Tractor | 470 CV | EURO III | 33T GVW The IVECO T-Way AT720T47WT H 6x6 Tractor is for sale and provides a heavy-duty all-wheel-drive platform for demanding transport, construction, infrastructure, industrial and remote-site operations. Powered by the C13 diesel engine producing 470 CV, this IVECO T-Way combines strong engine performance with a genuine three-axle 6x6 drivetrain and a professional tractor configuration. The vehicle is equipped with the 16TX 2240 TO transmission, mechanical suspension, a 3,800 mm wheelbase and a gross vehicle weight of 33,000 kg. Its 6x6 axle configuration makes the IVECO T-Way particularly relevant for transport operations where conventional road driving is combined with gravel roads, unpaved access routes, construction sites, industrial areas and other demanding working environments. A JOST fifth wheel, 3½" fifth-wheel configuration, 16 mm mounting plate and 15-pin trailer connection prepare the truck for professional semi-trailer operation. The Active Time cab provides a practical working environment with an air-suspended driver's seat, manual air conditioning, cruise control, Hill Holder, one bunk, external sun visor and Bluetooth DAB radio. For international operators searching for an IVECO T-Way 6x6 for sale, EURO III heavy-duty tractor, 6x6 off-road tractor or professional truck tractor for demanding transport, this configuration provides a strong combination of traction, mechanical durability and commercial transport capability. QUICK HIGHLIGHTS Key specifications of the IVECO T-Way AT720T47WT H 6x6 EURO III Tractor. - IVECO T-Way AT720T47WT H - SGT6 - Heavy-Duty Tractor Unit - Genuine 6x6 All-Wheel Drive - C13 Diesel Engine - 470 CV - EURO III Emission Standard - 33,000 kg Gross Vehicle Weight - 16TX 2240 TO Transmission - 3,800 mm Wheelbase - HR-TP Rear Axle - Rear Axle Ratio 4.67 - Mechanical Suspension - Front Parabolic Suspension - Rear Multileaf Suspension - 13R22.5 Tyres - Twin Rear Wheels - Drum Brakes Front & Rear - EBS + BAS - JOST Fifth Wheel - 3½" Fifth Wheel - 16 mm Fifth-Wheel Mounting Plate - 390-Litre Fuel Tank - Steel Front Bumper - Radiator Guard - Horizontal Air Filter - Active Time Cab - Low Roof - Air-Suspended Driver's Seat - Manual Air Conditioning - Cruise Control - Hill Holder - 1 Bunk - External Sun Visor - Bluetooth DAB Radio - Left-Hand Drive - 15-Pin Trailer Plug - 85 km/h Speed Limiter - Without Urea Tank - Worldwide Export Available HEAVY-DUTY IVECO T-WAY 6x6 TRACTOR A professional 6x6 tractor must combine road transport capability with additional traction when operating conditions become more difficult. Ijdpfxjzp Nwuo Apcoig The IVECO T-Way AT720T47WT H is configured as a three-axle 6x6 tractor, giving the vehicle all-wheel-drive capability across all three axles. This drivetrain configuration provides an important advantage for operators whose routes do not remain exclusively on paved roads. Construction projects, infrastructure developments, mining sites, energy projects and industrial operations may require a tractor to leave the main road and continue across gravel, loose surfaces or unpaved access routes. A conventional road tractor can be highly...

Condition: used, total width: 762 mm, total length: 1,448 mm, total height: 1,800 mm, For sale is a used Capsugel ULTRA 8 II, a semi-automatic capsule filling machine for powders in hard capsules. The machine is suitable for applications in the dietary supplement, pharmaceutical, and powder processing industries. The ULTRA 8 II is a production machine with a stainless steel design in the product and work areas, powder hopper, capsule feeder, rotating processing unit, and separate control cabinet. The machine shown is offered in its current condition and with the existing scope of supply. Technical data: Manufacturer: Capsugel / Lonza Capsugel Model: ULTRA 8 II Machine type: semi-automatic capsule filling machine / capsule filler Filling material: powder Processing: hard capsules; the actually installed capsule or format part must be checked on-site Production capacity: up to approximately 33,000 capsules/hour according to the manufacturer; the actually achievable capacity depends, among other things, on capsule size, product, dosage, format parts, operation, and machine condition. Format ranges specific to the series: depending on the format part, sizes from 000 to 5 are mentioned in comparable offers; the specific scope of supply of this machine must be checked based on the available format/change parts. Dimensions according to the manufacturer: approx. 1,448 × 762 × 1,800 mm (L × W × H) Installation area according to the manufacturer: approx. 1,448 × 762 mm Weight according to the manufacturer: approx. 680 kg Closing system: integrated, horizontal hydraulic closing system; according to the manufacturer, no compressed air is required for the closing process. Drives: variable speed drives for capsule alignment, dosing screw, and rotary table Vacuum: integrated vacuum pump Capsule feeder: large-capacity capsule hopper and automatic ring spinner Format change: "pinned" change parts for quick and reproducible setup Operation/control: digital displays and separate control cabinet Design: stainless steel table top, ring carrier, powder hopper, and enclosure Equipment and visible components: Stainless steel powder hopper Capsule feeder and rotating capsule holder Dosing and filling area Integrated drives and gearboxes Hydraulic assembly with pressure gauge Integrated vacuum unit Separate control cabinet with control, protection, and regulation components Isdpfxozvmnws Apcoig Emergency stop switch Stainless steel machine frame and enclosure

Condition: like new (used), Year of construction: 2019, functionality: fully functional, input voltage: 400 V, pressing force: 40 t, stroke length: 200 mm, total length: 1,600 mm, total width: 1,520 mm, total height: 2,450 mm, overall weight: 4,000 kg, Equipment: documentation/manual, safety light barrier, Hydraulic press brake Manufacturer: BYSTRONIC, Type: Xpert 40/1030 Iedpfx Apsz A Ex Sjcsig Year of manufacture: 2019, unused, originally packaged machine!!! Technical data Manufacturer: BYSTRONIC Type: Xpert 40/1030 Year of manufacture: 2019 Capacity: 40 t Hours: 0 Bending length: 1030 mm Stroke: 200 mm Distance between columns: 1060 mm Motor power: 7.5 kW Dimensions: L 1.52 x W 1.60 x H 2.45 m Weight: 4 t Equipment • 6-axis back gauge • Hydraulic clamping, top and bottom • RF-A tool holder, top • Height-adjustable display ByVision Bending with 22-inch Full HD touchscreen • Support table • Ergo LED work area lighting • Low-noise Dynamic Drive System (DDS) with integrated EnergySaver • OPC Interface Bending • Bending curve generator • Automatic tool overload protection • Rear sliding door with electric monitoring • Ergo foot switch • Tool package All information is without guarantee. A demonstration under power is possible at any time in our showroom.

Condition: as good as new (ex-display), functionality: fully functional, Year of construction: 2026, total length: 3,200 mm, For sale: a new CIDAN RAPIDO 32 electric guillotine from our showroom. The machine has not been used in production and is connected and fully ready for operation. It can be viewed in person, tested, and trial cuts can be performed. The machine is in stock – fast delivery is possible. The CIDAN RAPIDO is a fast and reliable electric guillotine designed for precise sheet metal cutting. The machine can perform up to 35 cuts per minute, making it ideal for both individual jobs and intensive series production. The drive system with eccentrics, the material clamping system, and the sheet support elements mounted close to the blades allow for convenient and precise cutting, even of narrow strips. The guillotine has angular supports on both sides of the front table, ensuring accurate sheet feeding at a 90° angle. LED lighting in the cutting area allows the operator to clearly see the cutting line. Key information: Manufacturer: CIDAN Machinery Model: RAPIDO 32 Condition: New / showroom machine Working length: 3200 mm Max. steel thickness: 2.5 mm Max. stainless steel thickness: 1.6 mm Max. aluminum thickness: 3.7 mm Cutting speed: up to 35 cuts/min. Weight: approx. 2100 kg CUTLINK control and automatic back gauge The guillotine is equipped with the CIDAN CUTLINK control system – a fast and easy-to-use program that allows up to 10 different operations to be programmed simultaneously. After the operator enters the required dimensions, the 750 mm automatic back gauge automatically adjusts to the required position, allowing for quick and accurate cutting of different widths. Sheet support and return The pneumatically controlled sheet support system allows for control of the material during cutting. Isdjzz Rqtepfx Apceig After cutting, the cut sheet is directed to the front material trolley, so the operator does not need to collect parts behind the machine. The trolley can be easily removed and transported, and also picked up with a forklift. Additional equipment included with this machine: Telescopic extension of the front table up to 800 mm from the cutting line – for easier positioning and support of large sheets. Material trolley – for collecting cut sheets and convenient transport to bending or other machines. LED cutting area lighting. Automatic 750 mm back gauge. CUTLINK control system. Ideally suited for sheet metal processing, roofing and facade manufacturing, ventilation, and other sheet metal processing companies. The machine is located in our showroom, connected, and ready for demonstration. Fast delivery is possible. If you have any further questions, please do not hesitate to ask.

Condition: used, maximum load weight: 36,250 kg, overall weight: 41,000 kg, axle configuration: 3 axles, first registration: 10/2025, next inspection (TÜV): 10/2026, Equipment: ABS, Excerpt from the equipment list. Complete equipment list available upon request. Frame: Chassis frame made of high-quality steel, but without an outer frame. Coupling plate with a 2-inch drawbar eye according to DIN 74080 / ISO 337. With crossmember and container locking mechanisms for accommodating: a) 1 x 45' High-Cube container b) 1 x 40' High-Cube container c) 1 x 30' ISO container, flush at the rear d) 2 x 20' ISO containers e) 1 x 20' ISO container, flush at the rear g) 1 x 45' ISO container h) 1 x 40' ISO container With 1 pair of height-adjustable container locking mechanisms and 3 pairs of foldable center supports, plus crossmember and container locking mechanisms for accommodating: f) 1 x 20' ISO container in the center Frame extension at the rear, mechanically extendable, load capacity approx. 5,800 kg, with spiral cable. Low-maintenance guidance on special plastic sliders and 2 extension rollers. KÖGEL frame extension at the front, manually extendable and mechanically lockable, incl. container guide on the left and right. Designed according to Directive 719/2015. Frame extension in the center, manually extendable and mechanically lockable with the tractor unit. Chassis: Axle lift mechanism on axle 1. Control of the axle lift is fully automatic and load-dependent. Starting aid: Activation via 3x brake, 30% overload up to a speed of 25 km/h. Operation on the chassis via switch. Additionally possible from the cab (switch in the cab necessary - PIN 12). When transporting 30' and 45' containers, the 1st axle CANNOT be lifted! BPW three-axle unit, with disc brakes Ø approx. 430 mm, mounting depth approx. 120 mm. Air suspension with approx. 180 mm travel. Vehicle Tires: Wheels with internal sensors according to UN ECE R141. Tires 6-fold 385/55 R 22.5 UNIROYAL TH 50. 6 steel rims 22.5 x 11.75, mounting depth approx. 120 mm (ET 120). Chassis Components: JOST landing gears, mechanically operated with leveling foot, 24 t lifting capacity. One-sided operation in the direction of travel, on the right. Splash guard system (spray suppression) according to Regulation (EU) No. 109/2011 for three-axle unit with 22.5 tires, consisting of: 3 pairs of semi-circular fenders with mud flaps. 2 chock blocks with holder. Side protection, according to ECE-R73, closed. Rear underrun protection made of square steel tube according to ECE-R58, screwable. Ijdozkx Hzspfx Apcjig Height of the underrun protection profile min. 120 mm, designed for increased test forces. Brake / Air Suspension System: EBS system 2S/2M with stability program (includes ABS/ALB function), EBS plug connection ISO 7638 (without connection cables), parking brake as spring brake, external pneumatic connections as well as external EBS diagnostic connection via ISO 7638 plug connection. Air suspension system incl. 1 raising and lowering valve, mounted on the left in the direction of travel in front of the axle unit. 2 non-interchangeable coupling heads at the front ISO 1728. Air reservoir for brake system and air supply made of steel (EN 286-2). Rear Impact Protection: Continuous steel rear impact protection, solid, on the end member at the rear. Information Systems: Tire pressure monitoring system according to UN ECE R141. Accessories: Document tube, diameter approx. 105 mm. Mounting on the left in the direction of travel on the side protection. 1 fire extinguisher 6 kg with pressure gauge (European approval). Mounting incl. holder and protective cover on the left in the direction of travel o

Condition: good (used), functionality: fully functional, mileage: 735,000 km, power: 353.04 kW (480.00 HP), first registration: 06/2018, fuel type: diesel, tire size: 315/70R22.5, axle configuration: 4x2, wheelbase: 3,800 mm, fuel: diesel, brakes: intarder, color: white, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, Year of construction: 2018, Equipment: ABS, AdBlue, Bluetooth, air conditioning, airbag, car registration, central locking, compressor, fog lights, low noise, navigation system, non-smoking vehicle, onboard computer, parking heater, power assisted steering, power mirror, second fuel tank, spoiler, traction control, IVECO STRALIS MY2016 - CHASSIS WJMM62AT20C392359 – PLATE GM580RZ YEAR 2018 – EURO 6 – 735,000 KM Color: SIGNAL BLUE (similar to RAL 5005) Cab: ACTIVE SPACE – STRALIS EVO Engine: CURSOR 11, 460 HP Tyres: size 315/60R22.5 STRUCTURE: Iijdpfx Apoykid Ejceg Wheelbase: 3800 mm, Double Bunk, Rear Air Suspension, ZF 12-speed gearbox 12TX 2210 TD – Payload 9,700 kg – GVW 18,000 kg – Towing Mass 3,570 kg TRUCK EQUIPMENT: Rear Air Suspension, ZF 12-speed Gearbox – 12TX 2210 TD, Hydraulic Retarder, Parking Air Conditioner, Automatic Climate Control, Independent Air Heater, Electronic Brake System + Brake Assist System, AEBS (ABS+ASR) + BAS, ESP, Adaptive Cruise Control, Hi Cruise (Predictive GPS), Lane Departure Warning System (LDWS), Ecofleet, Hill Holder, Ivecoconnect, Expansion Module, Pneumatic and heated Driver’s Seat, Sun Visor, Roof Spoiler + Side Deflectors, Plastic Parts in Cab Color, Heated 80L AdBlue Tank, Immobilizer, Central Locking, Built-in Fog and Depth Lights BODY TYPE: TRACTOR UNIT

Condition: used, mileage: 2,600 km, power: 18 kW (24.47 HP), first registration: 05/1975, fuel type: diesel, overall weight: 1,300 kg, color: green, gearing type: mechanical, suspension: other, operating hours: 2,600 h, Equipment: all wheel drive, 1. First owner, new inspection (MOT/emissions test), diesel, manual transmission, all-wheel drive, first registration: May 23, 1975, 2,600 operating hours, Holder rotary tiller, original condition, permissible total weight: 1,300 kg, first-owner version, lawn tires also possible (both are available). FOR US, THE CONDITION AND OUR GUT FEELING ARE DECISIVE; THE PRICE IS SECONDARY. If you have any further questions, please do not hesitate to contact Mr. Schlägel at the following number. //*TRADE-IN, PART EXCHANGE, OR FINANCING OF YOUR VEHICLE IS POSSIBLE! All information is without guarantee.* You can find more offers on our website: The description and specified data do not constitute a warranty and are not binding. The purchase contract concluded at the car dealership when purchasing the vehicle is binding. Errors and prior sale are subject to change! Iisdovictmopfx Apcog

Condition: used, power: 33 kW (44.87 HP), Year of construction: 2010, operating hours: 2,910 h, Equipment: cabin, front linkage, * Stoll vacuum superstructure with supports * Flatbed body * Articulated steering * Front attachment with hydraulics & PTO * Rear mounting bracket with PTO Isdpjvhv Smofx Apcjig * Work lights & beacon * 3000 kg permissible total weight * 31x15.50-15 tires -----Errors and prior sale excepted Vehicle number 5058 WhatsApp support available! If you have questions about the vehicle or need more information, feel free to contact us conveniently via WhatsApp

Condition: ready for operation (used), functionality: fully functional, control type: manual, actuation type: hydraulic, Geka (Spain) Hydraulic Punching, Shearing, and Notching Machine Model: Hydracrop–55/110A Year of Manufacture: 2001 Flat Bar Shear Capacity: 300 x 15 mm / 200 x 20 mm Blade Length: 305 mm Square: 25 mm Working Height: 880 mm Angle Shear Capacity: 1100 kN Deformation-free Angle Iron: 120 x 120 x 10 mm Angle Iron 45° Shear: 70 x 70 x 7 mm Round and Square Bar Shear Round Steel: 40 mm Square Steel: 40 mm Notcher Sheet Thickness: 10 mm Angle Iron: 100 mm Notch Depth: 90 mm Notch Width: 42 mm Punching Station Capacity: 550 kN Maximum capacity with quick-change system: Ø 40 x 10 mm / Ø 20 x 20 mm Throat Depth: 250 mm Stroke Length: 60 mm Working Height: 1085 mm General Specifications Number of strokes per minute at 20 mm stroke: 25 Power: 3 kW Net weight: 1320 kg Gross weight: 1518 kg Dimensions (L x W x H): 1600 x 1100 x 2000 mm Machine Details - 2 cylinders: one for the punching side, one for the shearing side - Punching unit with quick-change system - C-frame die holder + extra support - Nipple and die up to Ø 40 mm selectable - Flat bar shear incl. support table and 45° and 90° guides - Angle shear - Round and square bar shear (suitable for mounting U and I profiles as well) - Rectangular notcher - Emergency stop - Key switch for notcher safety - Selector switch for deep or shallow punch/shear operation - Selector switch for foot pedal / back gauge - Stroke adjustment for punch and shear side - 2 foot pedals - Scrap collection tray for punch slugs - Dutch instruction manual Includes: Punch table incl. back stops Notching table incl. back stops Electric length stop 1000 mm 30 sets of punch nipples Price of the Geka Hydraulic Punch/Shear/Notch Machine: €16,500 Machine is as new, original paint, like new, original finish Delivery conditions: Delivery time: from stock, subject to prior sale Delivery: ex works Baarle-Nassau Payment: before collection Prices: net, excluding VAT Machinehandel De Leeuw BV cannot be held liable for discrepancies between the technical specifications in this offer and the actual machine, accessories, and/or parts. Machines, accessories, and parts are sold as-is and as known to the buyer. We cannot provide a warranty for used machines, accessories, and parts. Delivery terms: Delivery time: ex stock, excluding VAT Delivery: ex works Baarle-Nassau Payment: before collection Prices: net, excluding VAT Machinehandel De Leeuw BV is one of the few companies in Europe that stocks and sells primarily used Kardex Remstar automatic lift and rotating warehouse systems. We install and/or dismantle these systems safely with VCA-certified engineers and have been doing so for more than 33 years. Best regards, Antoine de Leeuw Machinehandel De Leeuw BV Oordeelsestraat 7-B 5111 PA Baarle-Nassau Iiodpfeyxpawsx Apceg The Netherlands VAT No.: NL800103026B01 Chamber of Commerce Tilburg 18034279

Condition: excellent (used), Year of construction: 2017, operating hours: 3,200 h, pressing force: 130 t, Space requirement: 11,500 mm x 10,000 mm + Increased installation height/lift + 230 mm + 4-axis backgauge system + Rear work area lighting + Front work area lighting - TruBend documentation Automation BendMaster (60) Standard equipment: BendMaster - Sturdy base frame and manipulator made of cast aluminum construction - Load capacity 60 kg, sheet plus gripper - Low-level floor track in welded construction - Sheet sensor for contour detection - Rotary feedthrough for quick gripper change Gripper coupling on the BendMaster - Sensor system for 4-axis backgauge system - Electric drives - Double sheet detection - NC regrip station - Vacuum generation for suction grippers Control - TRUMPF PC control with operator terminal - Teleservice via internet - Convenient operation: screen, mouse, keyboard Safety - Safety fence with access door Special equipment + Track extension to 10 m + Gripper change console + Modular vacuum gripper without separation (materials for 3 grippers) + Modular vacuum gripper with separation (materials for 3 grippers) + Clamp gripper with rotary axis + Sheet removal station with linear axis + Additional pallet for sheet removal station + Right-hand side door for safety fence (or left-hand side in combination with ToolMaster) Machine - Robust machine frame entirely in steel construction - Press beam - Spherical mounting of pressure beam with inclined position - Electro-hydraulic upper drive system with 4-cylinder technology Iodpexayl Dsfx Apcjig - Optical set-up and positioning assist with control valves - Generous free space for bending - Flat front covers - Block hydraulic system - Electronic pressure gauge - Measuring system with glass scale and spring-back compensation - Hydraulic oil in machine (lifetime lubrication) - Oil cooler - Electrical cabinet cooling via air-to-air heat exchanger - Modern machine design Backgauge System - 2-axis backgauge system, X and R axes Tool Clamping - Hydraulic upper tool clamping - Lower tool holder, hydraulic clamping, hardened - Lower tool displacement, 2 positions, pneumatic Crowning - CNC crowning Control - TRUMPF TASC 6000 - Graphical workshop programming - Windows XPe (embedded), Pentium 4 with 2.8 GHz clock speed - 2 GB RAM - 15-inch touch screen - Network capability - Teleservice via internet Operation - Control panel with LCD keypad and foot switch - Communication rail - MobilControl Safety - Standard safety equipment - CE marking

Condition: new, pressing force: 135 t, operating speed: 10 mm/s, reverse speed: 130 mm/s, table height: 940 mm, overall weight: 7,750 kg, MVD SERIES B - 3,100x135Tn SERIES B - 4 Axes Large press brake for achieving outstanding bends and flawless workpieces The body and upper beam are of steel construction, designed according to minimum and optimum strength criteria. Isdpfx Aexfzpzopceig Model: B135/3100 Bending force: 135 tons Bending length: 3100 mm Distance between uprights: 2600 mm Ram stroke: 260 mm Daylight: 465 mm Throat depth: 410 mm Table height: 940 mm Length x Width x Height: 4690 x 2340 x 2980 mm Approach speed: 210 mm/s Return speed: 130 mm/s Bending speed: 10 mm/s Oil tank capacity: 180L Main motor: 11 kW Weight: 7,750 kg Standard features: CNC 3 axes Y1, Y2, X 260 mm stroke, 410 mm throat depth ESA S630 CNC control unit ± 0.03 mm precision SERVO-driven, motorized rear gauge X = 750 mm Promecam quick-release punch holder Sliding front sheet support arms Special narrow bottom table by MVD (European type) GIVI optical linear scales Standard punch tooling (H: 67, 850 R:08) Standard die tooling (60x60 mm, 4 Vee V=16-22-35-50 mm, 85°, H:60) LED lighting in RAM Optional features: Choice of X-axis backgauge options with 2-4-6-8 stops Wide bottom table for Multi Vee forming dies Anti-deflection crowning with original Wila wedges AKAS or DSP front laser safety systems Additional backgauge fingers Front laser safety