Double-Screw Bunker

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, input voltage: 400 V, total height: 2,200 mm, total length: 7,500 mm, total width: 1,500 mm, overall weight: 4,000 kg, TECHNICAL DETAILS Overall height: 2,200 mm Ncjdsy Akytspfx Afajr Overall length: 7,500 mm Overall width: 1,500 mm MACHINE DETAILS Weight: 4,000 kg Year of manufacture: 2007 Voltage: 400 V Power consumption: 46 A Fuse: 63 A Transport dimensions: 7,500 mm x 1,500 mm x 2,200 mm (L x W x H) Transport weight: 4,000 kg EQUIPMENT Tools included: Yes (for 1st, 3rd, 4th, 5th, 7th, and 8th unit) Tools included: No (for 6th unit)

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC Nsdpfx Afewp Rqfjascr The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, machine/vehicle number: 241306, saw blade diameter: 500 mm, cutting height (max.): 170 mm, cutting width (max.): 395 mm, power: 7.5 kW (10.20 HP), borehole diameter: 30 mm, TECHNICAL DETAILS Max. cutting width: 395 mm Max. cutting height: 170 mm Saw blade diameter min.: 490 mm Saw blade diameter max.: 500 mm Saw blade bore diameter: 30 mm Feed table length: 5,640 mm Output table length: 1,180 mm Feed speed: Automatic MACHINE DETAILS Nsdpfjy Akvnsx Afascr Voltage: 400 V Power consumption: 16.5 A Fuse: 32 A Power: 7.5 kW Transport weight: 800 kg Transport packages: 3 EQUIPMENT Automatic feed system

Condition: ready for operation (used), Year of construction: 2018, machine/vehicle number: P0220118, functionality: fully functional, pressing force: 9 t, number of cylinders: 6, workpiece length (max.): 2,500 mm, workpiece width (max.): 1,300 mm, workpiece height (max.): 200 mm, Equipment: CE marking, TECHNICAL DETAILS Max. workpiece length: 2,500 mm Max. workpiece width: 1,300 mm Max. workpiece height: 200 mm Number of cylinders: 6 Total working pressure: 90,000 N Working pressure: 294,200 N/m² MACHINE DETAILS Dimensions & weight Dimensions (L x W x H): 3,000 x 2,070 x 1,670 mm Nsdey Akukepfx Afaecr Unladen weight: 4,000 kg EQUIPMENT CE marking

Condition: new, Year of construction: 2025, Working width 300 mm Working length 1100 mm Ncsdpfx Afjgykaujajr Brush diameter 190 mm Brush rotation speed 1500 rpm Spindle diameter 40 mm Number of brushes 2 pcs.(metal + plastic) Max. speed of the feeding belt + smooth adjustment 0 - 10 m / min. Working height 940 mm + 50 mm Max. material height 300 mm The diameter of the extraction port 2 x 120 mm Overall dimensions Length 1240 mm Height min / max 1350/1650 mm Width 950 mm Weight 435 kg Total power 4.65 kW Voltage 400V Massive casing, as a result, ensures high stability Working height 940 mm + 50 mm and max. 300 mm material height gives you the freedom to process large materials Two independent brushes (steel, plaster) with powerful motors, with precise manual adjustment allow you to achieve high product quality Two independent extractors ensure smoothness of the removed sawdust and dirt The machine is made of high-class materials, which guarantees reliability high-quality workpieces Stepless speed control of the conveyor carpet allows you to achieve smoothness and intended productivity Optimat's many years of production experience allows us to meet the highest standards machine tool for every budget

Condition: ready for operation (used), functionality: fully functional, total length: 4,400 mm, total width: 1,400 mm, number of cylinders: 8, TECHNICAL DETAILS Number of levels: 1 Number of cylinders: 8 Ncjdpfoy Akihjx Afajr MACHINE DETAILS Type of heating: Oil Machine dimensions (L x W): 4,400 x 1,400 mm EQUIPMENT Glue roller Infeed/Outfeed

Condition: ready for operation (used), Year of construction: 2011, machine/vehicle number: 5/1-107, functionality: fully functional, total height: 1,730 mm, total length: 6,100 mm, total width: 1,440 mm, Equipment: CE marking, The machine has the following configuration: 1. Pre-milling unit (tools included) 2. Glue application unit 3. Pressure rollers (tools included) 4. End trimming unit (tools included) 5. Not specified (tools included) 6. Corner rounding unit (tools included) 7. Radius scraping unit (tools included) 8. Not specified (tools included) 9. Flat scraping unit (tools included) MACHINE DETAILS Number of units: 9 Voltage: 400 V Ncedpfx Aoy Akgtefaor Power consumption: 21.9 A Main fuse: 50 A Dimensions Dimensions (L x W x H): 6,100 x 1,440 x 1,730 mm Transport packages: 1 EQUIPMENT CE marking

Year of construction: 1995, condition: ready for operation (used), Four dissolvers from various manufacturers are available. 1) Niemann NLD I, year of manufacture: 1995. 2) Vollrath VDSVY 15, year of manufacture: 1992, shaft length: 700mm, disk diameter: 400mm, tank volume: 400l, tank diameter: 785mm, tank height: 990mm, outlet diameter: 45mm. 3) Vollrath VDSVY 40, year of construction: 1991, tank volume: 400l, speed: 1000rpm, shaft length: 700mm, disk diameter: 400mm, machine dimensions X/Y/Z: approx. 3200mm/800mm/1200mm. 4) Pendraulic WDV 10, speed: 1800rpm, shaft length: 985mm, disk diameter: 275mm, lifting height: 1250mm, machine dimensions X/Z: 560mm/3450mm, weight: approx. 850kg. On-site inspection is possible. Ncjdpfjvnuckjx Afaor

Condition: ready for operation (used), Year of construction: 2012, machine/vehicle number: AA2-002032, functionality: fully functional, operating hours: 9,974 h, overall weight: 7,450 kg, feed length X-axis: 5,020 mm, feed length Y-axis: 1,680 mm, feed length Z-axis: 250 mm, TECHNICAL DETAILS X-axis travel: 5,020 mm Y-axis travel: 1,680 mm Z-axis travel: 250 mm Nsdpsy Akgasfx Afajcr Number of axes: 5 Software: SCM XILOG MAESTRO Control systems: SCM PRISMA K, SCM TTS System, SCM TecPad, MORBIDELLI TV Matic, SCM PRO-SPACE, SCM RAPID 12, SCM RAPID 24 Tool changer: 36 positions Drilling units: 24 x vertical MACHINE DETAILS Machine dimensions (LxWxH): 2,400 x 8,000 x 2,400 mm Total weight: 7,450 kg EQUIPMENT - Vacuum pump with 250 m³/h capacity - Liquid-cooled milling spindle

Condition: ready for operation (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: AB/222595, total width: 1,950 mm, total length: 2,300 mm, total height: 1,850 mm, empty load weight: 1,240 kg, Equipment: CE marking, MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 2,300 x 1,950 x 1,850 mm Unladen weight: 1,240 kg Voltage: 400 V Power consumption: 10 A Ncjdpfsy Akdxsx Afajr EQUIPMENT CE marking

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Ncsdou Hmacopfx Afasr Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 4 main cutters 4 pre-cutters 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted

Condition: ready for operation (used), Year of construction: 2016, functionality: fully functional, saw blade diameter: 350 mm, saw blade bore: 30 mm, rotational speed (max.): 4,000 rpm, cutting length (max.): 3,200 mm, intake manifold diameter: 120 mm, TECHNICAL DETAILS Max. cutting length: 3,200 mm Saw blade diameter min.: 300 mm Saw blade diameter max.: 350 mm Saw blade bore diameter: 30 mm Dust extraction nozzle diameter: 120 mm Max. spindle speed: 4,000 rpm (automatically adjustable) MACHINE DETAILS Voltage: 400 V Power consumption: 18.5 A Nsdpoy Ai U Asfx Afajcr Fuse: 25 A Transport packages: 2

Condition: ready for operation (used), Year of construction: 2022, machine/vehicle number: 0-341-73-4415, functionality: fully functional, operating hours: 4,522 h, power: 7.5 kW (10.20 HP), cutting width (max.): 3,200 mm, saw blade diameter: 310 mm, saw blade bore: 60 mm, overall weight: 5,000 kg, TECHNICAL DETAILS Ncodjy Ai Upspfx Afasr Maximum cutting width: 3,200 mm Maximum cutting length: 3,200 mm Saw blade projection: 65 mm Maximum feed speed: 60 m/min Programmable pusher speed forward: 25 m/min Programmable pusher speed backward: 60 m/min Saw carriage speed: 60 m/min Manual crosscut stops: 4 units Saw blade bore diameter: 60 mm Maximum saw blade diameter: 310 mm Scoring unit bore diameter: 45 mm Scoring saw blade diameter: 150 mm MACHINE DETAILS Control: CADmatic 5 Main saw motor: 7.5 kW Operating hours: 4,522 Dimensions & Weight Transport dimensions: 8,000 x 2,400 x 2,000 mm Transport weight: 5,000 kg EQUIPMENT Intelliguide optical LED guidance system 1 air table 2,100 x 650 mm with roller elements 2 air tables 1,800 x 650 mm with roller elements 21.5-inch touchscreen CAD Plan 4 optimization software Clamping fixtures: 50, 250, 450, 1200, 2000, 2700 mm Scoring saw unit

Condition: refurbished (used), FULL LINE of Drilling, max working width mm 3200, with fast automatic handling equipment. Composed of the following machines: A) LOADER (Portal) "RBO" Winner C 3200 with double pick-up and central motorized rollers table. With 2 on-ground motorized rollers ways to in-feed the piles (stacks) of panels to loader. B) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° C) 1st Auotmatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units D) 2nd Automatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units Nedpfx Aedfgg Isfaocr E) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° G) UNLOADER-STACKER (Portal) "RBO" Winner SC 3200 with double pick-up, with double storage station, with central motorized rollers table. With 2 on-ground motorized rollers ways to out-feed the piles (stacks) of panels from the Unloader

Condition: ready for operation (used), Year of construction: 2008, machine/vehicle number: 8011510B, functionality: fully functional, filter area: 72 m², production capacity: 80,000 unit/h, Equipment: CE marking, TECHNICAL DETAILS Capacity: 80,000 m³/h Number of filter bags: 384 pcs Filter length: 2,500 mm Filter diameter: 230 mm Filter area: 72 m² MACHINE DETAILS Connected load: 15 kW Ncedpfx Asy Ai Tfefaor Weight of upper section with motors: 4,000 kg Weight of intermediate section with filter sleeves: 4,000 kg Weight of lower section with legs: 2,000 kg Main fan: 12 pcs Power of main fan: 15 kW Nominal air flow: 22 m/s EQUIPMENT Return lines Control cabinet CE marking Extinguishing system Control cabinet Shaking system Vacuum installation Note: The machine has already been dismantled.