Loader

Liebherr LTM 1050-3.1

Condition: used, mileage: 90,300 km, first registration: 08/2017, fuel type: diesel, tire size: 445/95 R 25, axle configuration: 6x6, fuel: diesel, brakes: retarder, suspension: hydraulics, total length: 11,840 mm, total width: 2,540 mm, Year of construction: 2017, Equipment: ABS, AdBlue, crane, cruise control, electric window regulation, retarder, = Additional options and accessories = - Mechanical tachograph - Hub reduction - PTO (Power Take-Off) - Radio/CD player = Further information = Axle configuration Front axle: Tire size: 445/95 R 25; Steered; Left tire tread: 40%; Right tire tread: 40%; Suspension: hydraulic suspension Rear axle 1: Tire size: 445/95 R 22.5; Steered; Left tire tread: 50%; Right tire tread: 50% Rear axle 2: Tire size: 445/95 R 25; Steered; Left tire tread: 50%; Right tire tread: 50% Dusdpfxezb Huie Ah Nju Weights Unladen weight: 35,850 kg Payload: 150 kg Gross vehicle weight (GVW): 36,000 kg Functional Lifting capacity: 50,000 kg Crane: Year of manufacture 2020 Condition Damages: none Identification Registration number: 96-BJT-9

Condition: excellent (used), Year of construction: 1995, operating hours: 45,000 h, pressure: 10 bar, operating pressure: 10 bar, For sale is a Loos steam boiler with Weishaupt oil burner. Gas burner available upon request. The unit is in very good condition. Model UL-S 5000, year of manufacture 1995. Steam output: 5,000 kg/h. Maximum steam pressure: 10 bar. Delivery available at extra cost. On-site inspection possible. Please contact us if you have any questions. Dsdjydq I Sopfx Ah Nsuu

Condition: used, functionality: fully functional, mileage: 141,000 km, first registration: 01/2009, fuel type: diesel, overall weight: 38,000 kg, axle configuration: 6x4, fuel: diesel, total height: 3,800 mm, Year of construction: 2008, operating hours: 14,100 h, Equipment: ABS, additional headlights, compressor, cruise control, differential lock, full service history, onboard computer, parking heater, tachograph, Liebherr LTM 1050-3.1 in very good technical and visual condition, regularly serviced and ready for immediate operation without any additional investment. The crane is fully functional and has undergone extensive maintenance with several key components replaced: - Complete replacement of the boom seal kit - Full hydraulic oil change Dedpey Nb D Asfx Ah Njuu - Full engine oil change - New heating system - New control system - New hydraulic winch brake All systems are fully functional and in excellent condition. The machine operates reliably, the hydraulic system works flawlessly, and the boom is leak-free with smooth operation of all functions. The cabin and controls are well maintained and ready for everyday use. The crane has been continuously maintained and serviced to ensure dependable, trouble-free performance. Suitable for immediate use in construction or lifting operations. Inspection and testing possible by arrangement. For more information, technical specifications, or additional photos, please feel free to contact me.

Condition: used, Aufspannplatte - Tisch einer Langhobelmaschine - Tischbreite/Aufspannbreite: 1845 Tischlaenge/Aufspannlaenge: 5505 mm 7 T-Nuten laengs fuer T-Nutensteine: M 30 T-Nutenabstaende zueinander: 263 mm Gesamtlaenge: 6230 mm Plattenhoehe insgesamt: 350 mm Dedpobn Amfjfx Ah Neuu Gewicht: 11 t

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Djdpfevf E Avjx Ah Nsuu Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: ready for operation (used), Compressor Bitzer Dsdjh Dht Dopfx Ah Nouu Type: 60-70.2 Volume: 219.1 m3/h Cooling capacity: 143 kW at -5°C/40°C, 118 kW at -10°C/40°C, 77 kW at -20°C/40°C R404A Pieces in stock: 3 Reference number: S 75 Condition: Used in good condition We have a lot of refrigeration equipment. Chillers, compressors, coolers, condensers, chillers, cold rooms, refrigeration and gastronomic furniture as well as machines and devices for restaurants and meat processing. See our other auctions or call us, not everything is machineseeker.

Condition: used, mileage: 4,295 km, first registration: 07/1998, fuel type: diesel, color: yellow, gearing type: mechanical, suspension: other, operating hours: 4,295 h, Equipment: all wheel drive, Quick coupler, radio, diesel Year of construction 1998 4,295 operating hours Quick coupler All-wheel radio Bucket Bale fork Control unit as good as new Equestrian farm machine FOR US THE CONDITION AND THE FEEL OF THE MACHINE ARE DECISIVE, THE PRICE IS IN SECOND PLACE If you have any further questions, please do not hesitate to contact Mr. Faller at the number. //*EXCHANGE, DEPOSIT OR RENTAL OF YOUR VEHICLE, AS WELL AS FINANCING POSSIBLE! All information without guarantee* You can find further offers on our homepage: The description and data given do not constitute a guarantee and are not binding. The contract of sale concluded at the dealership when the vehicle is purchased is binding. Subject to errors and prior sale! Dusdpjp Na Euefx Ah Nju

Condition: good (used), Refrigeration compressor, refrigeration machine, cooling compressor, refrigeration unit, cooling compressor, compressor, motor compressor, cooling machine, cooling unit -Manufacturer: Bitzer, Compressor Motor Compressor -Type: BHS 592 S -Power: 3 kW / 1450 rpm -Volume flow rate: 22.14 m³/h -Max. operating pressure: 24.5 bar -Number: 2x cooling units available -Price: per piece -Dimensions: 550/315/H390 mm -Weight: 88 kg Duedpfxsguzr Hj Ah Nju

Condition: like new (used), Year of construction: 2000, operating hours: 25,000 h, travel distance X-axis: 10,300 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 1,800 mm, feed rate X-axis: 10 m/min, feed rate Y-axis: 10 m/min, feed rate Z-axis: 10 m/min, position of the milling head: 2.5 x 2.5 °, spindle speed (max.): 3,000 rpm, spindle speed (min.): 60 rpm, table width: 3,300 mm, table length: 12,000 mm, mount diameter: 50 mm, total height: 48,750 mm, total width: 100,000 mm, total length: 212,000 mm, overall weight: 100,000 kg, Duplex milling are two machines located one opposite the other which can work seperately or as single machine, workpiece can be machined with 2 simultaneous spindles. Production increase of up to 50% in relation to conventional solutions, i.e. individual milling machines Improvements in part precision, by managing to do the machining of the part in one single setup, in most of the cases One sole operator can control the DUPLEX milling machines Reduced space and investment requirement comparing with two single machines Fast investment amortization due to the high productivity Duplex solution admits different configurations: single working area, pendulum working areas For machining excavator arms / boom like, CAT, Caterpillar, Komatsu, Hitachi, Hyundai, Doosan, Case, Bobcat, JCB, Kobelco, Liebherr, Kubota, Takeuchi, Volvo Djdperx Rxtefx Ah Neuu X-Axis: 10300mm Y-Axis: 2000mm Z-Axis: 1800mm Table Length: 12000mm Table Width: 3300mm Table load: 100000 Power on spindle: 22/30kW Spindle speeds: 60 - 3000Rpm Spindle Taper: 50ISO/Bt/Mk Feed rate X-Axis: 10000mm/min. Feed rate Y-Axis: 10000mm/min. Feed rate Z-Axis: 10000mm/min. Millinghead auto-index:2.5 x 2.5° Working hours: 25000H Length: 21200mm Width: 10000mm Height: 4875mm Weight: 100000kg

Condition: excellent (used), Year of construction: 2004, winch inkl. lifting capacity max. 2t. auf 2,7 Meter lifting capacity max. 1 Tonne auf 5,3 Mete Number of working hours 270 h Dujdpjq N E U Aefx Ah Nju electrical ja