Forklift

Hyster H7.00XL

Condition: used, functionality: fully functional, Year of construction: 2002, fuel type: gas, Forklift Hyster H 7.00 XL Year of manufacture: 2002 Operating hours: 7432 Overall height: 3.25 m Lifting height: 4.4 m Fork carriage width: 2 m Full cab with heating Free auxiliary hydraulics With sideshift Bedsyvvuijpfx Acnjll Forks 1.2 m and new forks 2.4 m

Condition: good (used), functionality: fully functional, Sheet width: 4050 mm Sheet thickness: 8 mm Bedpfx Aexu Nc Ijcnjll Cutting angle: 2 - 10° Cutting speed: 0.053 m/s Table length: 710 mm Machine weight approx.: 10,100 kg

Year of construction: 1975, condition: good (used), functionality: fully functional, drive type: Diesel 130 Kw, Patrol boat from the former GDR, later used by the Berlin Water Police (WSP 1), IFA 6-cylinder diesel engine. Winter-capable, icebreaker rating up to 3 cm thickness, certified for all waters including open sea. Dimensions: 11.90 m length, 2.90 m beam, draft 0.90 m. Top speed: over 30 km/h. Engine: Schönebeck 6-cylinder, 4-stroke diesel, type DM 6 VD 14.5/12-1. According to research, the engine delivers either 170 or 220 HP from 10 L displacement. These engines are known for low fuel consumption: at canal cruising speeds (8–12 km/h), consumption is 6–8 L per hour. Equipment includes signal mast, mast spotlight, boat lighting. Dual helm positions: inside cabin and flybridge. AGM batteries, engine start with 24 V system, 12 V onboard network. Brand new onboard toilet. Electric and manual bilge pumps (automatic/manual operation). Complete overhaul from 2021 to 2023: 5-layer primer and 3-layer antifouling coating. Steel hull, aluminium superstructure. Bjdpfjy D Rk Isx Acnjll New electrical wiring, new exhaust system, new clutch, engine overhauled, fuel tank serviced, new lines installed, new air filter. Engine starts and runs flawlessly, forward and reverse gear shifts without issues. Some work is still required to complete comfort features. The vessel is suitable as a small tugboat or as a work or fishing boat. Lower helm station: the gauges still need to be installed; required instruments and switches are included.

Condition: used, WEBSTER & BENNETT EV 36” HIGH SPEED VERTICAL BORER MAKE WEBSTER & BENNETT, MADE IN ENGLAND MODEL EV 36” TABLE DIA 915 mm SWING 1168 mm HEIGHT UNDER RAIL 533 - 1016 mm SPEED 13.5 - 300 rpm FEED RATE 0.005-0.250 inch/min MAIN SPEED 40 HP PLUS HIGH SPEED TAABLE EV SERIES MACHINE ELEVATING RAIL SAFETY GAURDING SET OF JAWS FULLY FUNCTIONAL GOOD SLIDES Bledpfxoxp Na Ns Acnjl

Condition: used, Year of construction: 2012, x-travel 2100 mm y-travel 1020 mm z-travel 762 mm Control Fanuc MXP-200FP spindle speed 6000 U/min spindle capacity ca. 22 kW max. torque on the spindle ca. 550 Nm tool taper SK 50 table surface area 2300 x 1020 mm max. table load 3000 kg T-slots 6 x 22 mm T-slot - distance 150 mm 3-Axis CNC Machining Center Bledpfx Acsx Sr A Uensl Equipment/Accessories: - Automatic tool changer with chain magazine, 40 stations - max. tool-Ø: 120/240 mm - max. tool length: 350 mm - coolant system with internal coolant supply and filter - emulsion mist extraction - electronic handwheel - 2 pcs. magnetic clamping plates 800 x 400 mm - various tool tapers SK50 - chip conveyor

Condition: ready for operation (used), Year of construction: 2021, A Wacker Neuson wheel loader, ideally suited for agricultural purposes, is available. Engine: Deutz TD 2.9 L4 S5, Power: 61hp/45kW, Displacement: 2900cm³, Emission standard: Stage V, Exhaust aftertreatment: DOC/DPF, Max. engine speed: 2300rpm, Max. tipping load: 3300kg, Standard bucket capacity: 0.8m³, Max. working hydraulic pressure: 220bar, Max. travel hydraulic pressure: 450bar, Fuel tank: 82l, Kinematics: Z, Articulation angle: 44°, Oscillation angle: +/-12°, Max. dump height: 2430mm, Lifting force: 41.36kN, Outside turning radius: 3870mm, Tires: 405/70 R20. Transport dimensions X/Y/Z: approx. 4800mm/1850mm/2550mm, Operating weight: approx. 4600kg, Operating hours: approx. 1382h. Including 1200mm pallet forks, FEM II rotating fork positioner, road approval and hydraulic Z-HV quick coupler. The engine or the control system of the windshield washer system has a defect. Documentation available. An on-site inspection is possible. Bodpfszhw Skex Acnell

Condition: used, Year of construction: 2011, Maximum grinding length: 1200 mm Maximum grinding length with table dresser: 1000 mm Maximum grinding width: 600 mm Grinding height (table to underside of grinding wheel): 550 mm Table load with magnetic chuck: 975 kg Table load without magnetic chuck: 1200 kg Table speed: 1 - 40 m/min Grinding spindle Motor spindle: 11 kW Grinding wheel: 406 x 152.4 x 100 mm Speed: 1400 rpm Longitudinal axis (Z-axis) Rapid traverse: 5 m/min Adjustable feed: 1 - 50 mm Continuously variable feed: 0 - 2000 mm/min Smallest infeed: 0.001 mm Vertical axis (Y-axis) Rapid traverse: 1.5 m/min Bjdpfexhdz Eox Acnell Smallest infeed: 0.001 mm Space requirements approx.: 4450 x 2935 x 2540 mm Total weight approx.: 6700 kg Equipment: - Electro-permanent magnetic chuck 1000 x 500 mm incl. electronic control module and potentiometer - Coolant cleaning system with paper filter and magnetic separator 350 l – delivery rate 100 l/min - Static frequency converter incl. automatic dressing compensation - Complete extraction system - Siemens control with electronic handwheel - Various accessories, 2 flanges and 5 grinding wheels

Condition: used, functionality: fully functional, Year of construction: 2019, operating hours: 873 h, load capacity: 5,000 kg, lifting height: 3,300 mm, fuel type: diesel, mast type: duplex, construction height: 2,450 mm, fork carriage width: 1,200 mm, fork length: 2,400 mm, empty load weight: 7,850 kg, drive type: Diesel, construction width: 1,450 mm, Diesel forklift Load center: 600 Mast type: Duplex Bedevgh U Rspfx Acnoll Technical condition: good Front tire size: 300-15/8.00 Rear tire size: 7.00-12/5.00 Sideshift, 3rd valve, 4th valve, front working lights, heater, full cab, CE certificate, safety light,

Condition: new, Year of construction: 2012, welding current 20 - 100 A cutting capacity max. 35mm mm open-circuit voltage 250 V Required air-pressure min. 4 bar connected load 20 KVA connected load frequency 400 V weight 0,7 kg Dimensions (LxWxH) 1,0 x 0,6 x 0,8 mm Bljdpjw En E Ejfx Acnsl Plasma cutting machine with cart - Includes 7m hose package - Spare nozzles

Condition: new, pressure 100 t stroke 400 mm 1010 mm Blsdpfx Aeyv N Ngecnsl 295 mm Heads 175x115 mm feed down 7,6 mm/sec feed up 13,4 mm/sec total power requirement 4,0 kW weight of the machine ca. 1000 kg dimensions of the machine ca. 1600x850x2450 mm Domestic equipments: - Stable welded construction - Pressure cylinder laterally adjustable - Electric control via selector lever / manually via hand lever - Pressure gauge via pressure gauge - Material requirements - CE mark