Receiving belt

Forderband Transportband Conveyor

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Gsdpfxeu Thhre Ag Djuk Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, functionality: fully functional, overall weight: 44,000 kg, rotor length: 2,800 mm, power: 315 kW (428.28 HP), rotational speed (max.): 87 rpm, - MERAK 2800-2 with 315 kW - Cutting system 116PR - PG190 screen (can be changed on customer request) - Feed chute - Dust suppression Godpougf Dwsfx Ag Deuk - Electrical central lubrication - Hydraulic safety guard - Overband magnetic separator Neodymium - HP - Rubberized bolted floor plates on tracked chassis

Year of construction: 2003, condition: excellent (used), For sale: KURTZ cutting line mod.VBR-S3 (Complete set: cutting KURTZ mod. VBR-S3, KUKA selection robot, packaging VIRO mod. PPZA-1300/24/MZG, palletizing, wrapping) EPS block cutting line with maximum dimensions of 5000x1200x1200. A block option of 600x1200x2400 is also available Complete line in "U" arrangement, consisting of: - Block buffer loading by dump truck - Horizontal cutting with automatic wire positioning, with double-frame cutting and oscillation - Polystyrene waste/scrap removal system: top, bottom, sides - Side cutter with manual wire positioning - Down cutter with automatic wire positioning - Anthropomorphic robot for product selection - VIRO packaging machine - Rotation of packages for cross stacking - It is possible to palletize different size polystyrene boards on wooden pallets or on glued polystyrene strips under the column with stacked polystyrene packages - Automatic stacker/palletizer for creating columns up to 3 meters high and up to 3 meters long - Vertical wrapping machine for automatic stretching of columns of polystyrene packages - Complete with inkjet printers and automatic labelers - Siemens S7 PLC controller - Complete with safety barriers with switch type protection - High-capacity line, in very good condition, requires an area of about 600 m2 (40m x 15m) - Year of manufacture: 2003 Gjdpsuct Upofx Ag Deuk - Electricity requirements: 400V; 50 Hz; 115 kW; 300A

Condition: ready for operation (used), Year of construction: 1996, For sale: conveyor belt, 20 m long, belt width 0.8 m. Galvanized steel construction. A new belt is included with the conveyor. Possibility of transport. Gedpfxsu Tpi Ds Ag Djuk

Year of construction: 2023, condition: new, Polyp Scrap Grapple for Cranes Palfinger Hiab Capacity: 300 Lt / 0.3 m3 Model: 4 Tinned - Half Closed Gross Weight: 450 Kg Guedpfx Agonziblj Dsk

Condition: used, Year of construction: 2006, No. 10024 Stationary single-shaft shredder Doppstadt DW 2560 E1 Used, year of construction 2006 Overhauled by Doppstadt in 2024 (new shaft / new gearbox / new bearings / etc.) Since overhaul approx. 500 operating hours Electric motor Approx. 20000 operating hours The scope of delivery does not include a conveyor belt Filling width 1900 mm / filling length 3060 mm Motor: Manufacturer T-T Electric / type DC motor LAK 4250 C / power 315 kW / rated speed 2000 rpm / armature voltage 460 V / armature current 721 A / field voltage 340 V / field current 14.8 A / degree of protection IP 55 / cooling 2 separate motors Hydraulic unit: Manufacturer OC-Hydraulik Doppstadt / power 7.5 kW / rated voltage 380 V Cutting unit: Roller / length 2500 mm / diameter 600 mm / speed 31 rpm Throughput: shredded material up to 40 t/h Transport dimensions approx. 8000 (7850) x 4700 (3450) x 5380 mm LWH Godpjwh S I Njfx Ag Douk Weight approx. 25665 kg Sale on behalf of the customer, ex location near 85456 Wartenberg, without dismantling, without transport and assembly Errors in description and price excepted Dismantling, transport and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: used, Year of construction: 2014, operating hours: 18,700 h, overall weight: 27,000 kg, number of blades: 41, rotor length: 1,800 mm, power: 200 kW (271.92 HP), rotational speed (max.): 87 rpm, input voltage: 400 V, Slow-speed, robust single-shaft shredder suitable for the pre-shredding of various materials without heavy contaminants. Applications: Shredding of industrial and commercial waste, films, packaging materials, textiles, paper, rubber, demolition wood, pallets, paper rolls, cable drums, and mixed plastics for thermal recovery or material recycling, whether loose or baled. Lindner Jupiter 1800 Drive power: 1x 200 kW (ABB) Screens: SK 80 mm Control cabinet: complete with (ABB frequency inverter) Recooling unit: Yes, included Feed opening: 1790 x 1750 mm Filling volume: approx. 4 m³ Rotor length: 1770 mm Rotor diameter: 745 mm Rotor speed: 50Hz : 87 rpm Number of rotor knives: 41 pcs Knife dimensions, pointed knives: 87x87x38 mm Counter knives, lower: 5 pcs Scraper comb, upper: 5 pcs Hydraulic feed: 11 kW Gujdpfew Tk Udjx Ag Dok Weight: approx. 27 t Dimensions LxWxH mm: 4800 x 3260 x 3090 mm Hopper: included Delivery time: immediate

Condition: ready for operation (used), Böhringer Hopper with Vibrating Chute Brand: Böhringer Dim. bunker: 4500 x 2200 x 1000 mm. (new) Gsdpfx Aotznbvjg Deuk Vibrating Chute: Length 4000 mm – width 1100 mm. Drive: 2 pieces of vibration motors of 4 kW each.

Condition: used, Year of construction: 2008, operating hours: 30,000 h, functionality: fully functional, machine/vehicle number: XR203724, number of blades: 36, rotor length: 2,000 mm, rotational speed (max.): 30 rpm, Single-shaft shredder UNTHA XR2000S, currently in operation in a three-shift system for alternative fuel production, available for sale from January 2026. Rotor length 2,000 mm, 36 rotor knives, hydraulic pusher, two 132 kW drive motors, two slip clutches, two gearboxes. Various spare parts are available in addition to the shredder: spare rotor, spare gearbox, spare motor, screen clamping bars, knives, etc. Guodpowz Ex Uofx Ag Dok

Condition: refurbished (used), conveyor belt length: 40,000 mm, conveyor belt width: 800 mm, power: 22 kW (29.91 HP), smooth belt EP630 6:3 SIEMENS electric drive 22 kW Feed and discharge hopper Guodpfx Aetp Ig Tsg Dok stable V-support