Low loader semitrailer

FAYMONVILLE Multimax Plus Satteltieflader Hebebett

Condition: new, maximum load weight: 36,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. A selection of features is listed below. Complete equipment upon request. GOOSENECK: * Gooseneck in SNT design to optimize the bed length, approximately 3,700 mm long, with a rear bevel of approximately 1,000 mm x 6° * For SZM (tractor unit): 4 x 2 and 6 x 2 * ASPÖCK-UNIBOX * The gooseneck and the rear bevel have a grid flooring with a 5 mm sheet metal reinforcement * 2-inch King Pin * Guide plate on the gooseneck for the turntable, approximately 500 mm wide Djdpfx Aasy Auhheysuw * Round NATO socket on the connection strip at the front (Maeler & Kaege VG 96 917) * On the gooseneck, one pair of plug-in aluminum sideboards, approximately 400 mm high, in an anodized finish * One LED work light each on the left and right at the top of the front wall, with operation via an on/off switch (operation of the work lights from the SZM is not possible in this case) LOADING AREA: * Loading area, approximately 9,600 mm long, with a rear bevel of approximately 900 mm x 6° * The loading area behind the gooseneck can be hydraulically raised and lowered, approximately 3,000 mm long, with a load capacity of up to approximately 9,000 kg * Continuous grid flooring on the lifting platform and loading area with approximately 5 mm sheet metal underneath as additional reinforcement, designed for point loads TIRES: * 235/75 R 17.5 3PMSF, twin tires. Brand of our choice * TPMS tire pressure monitoring system in accordance with ECE R 141 AXLES: * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle trailing * 3rd axle with electro-magnetic reversing lock, activated via reverse gear and manually * 1st axle with starting assist * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve HYDRAULIC LOADING RAMPS: * One pair of two-part AXS steel ramps with grid flooring, approximately 4,920 mm long and approximately 900 mm wide * Hydraulically foldable ramp tips * Ramps can be hydraulically shifted outwards by approximately 235 mm and inwards by approximately 365 mm individually * Strobe lights on the outside of the ramp tips, with a switch next to the ramp operation control * Ramp locking in the driving position by means of a quick-release fastener * Painted sand coating on the outer frame of the ramp and on the ramp tip * Mechanical supports in downpipe design on the sides of the ramps to provide support when docking with loading ramps * Control valves for the hydraulic ramps on the right side of the vehicle BRAKE SYSTEM: * Brake system from WABCO EBS-E, in accordance with EU regulations SURFACE TREATMENT: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection PAINTING: * Trailer: Carmine Red (RAL 3002) * Rims: Silver-grey * Sideboards: Aluminum, natural finish * Wheel hubs: According to axle manufacturer * Lamp panel: Pure white (RAL 9010) EQUIPMENT: * Front wall made of steel, plug-in, approximately 1,600 mm high, including connection strip for supply lines to the SZM, mounted approximately 1,000 mm from the bottom edge of the outer frame profile * Attachment option for lashing chains on the inside of the front wall on the left and right, including aluminum trough underneath on the left and right for storing chains or lashing straps * Approximately 12 mm thick DELIGNIT flooring screwed to the back of the front wall * Two pairs of screwable lashing

Condition: new, maximum load weight: 36,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You will find our complete vehicle inventory, including immediately and soon-to-be available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. - Gooseneck in SNT design to optimize load platform length, approx. 3,700 mm long, with a rear taper approx. 1,000 mm x 6° - For tractors: 4 x 2 and 6 x 2 - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets - 3 kW electro-hydraulic power pack for hydraulic operations (excluding hydraulic winches). Without supply line installation on the tractor unit - Outer beams of the gooseneck with mounting holes for boltable lashing rings. First hole approx. 200 mm from the front, subsequent holes approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) - One mounting hole at the rear upper part of the gooseneck’s outer beams for a boltable lashing ring - 1 pair of screw-in lashing rings included (LC 10,000 daN) - 3 pairs of recessed lashing rings inside the gooseneck’s outer beams (LC 5,000 daN) - 3 pairs of recessed lashing rings in the center of the gooseneck (LC 5,000 daN) - 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN) - Grating covering on the gooseneck and rear taper with 5 mm steel reinforcement - 2" kingpin - Round NATO socket at the front connection panel (Maeler & Kaege VG 96 917) - Spiral cable for powering the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m long) between trailer and tractor unit, with plug (NATO-NATO) - 1 pair of detachable aluminum side boards on the gooseneck, approx. 400 mm high, anodized finish Dsdpfx Aaoyhkqueyeuw CARGO AREA: - Cargo area, approx. 9,600 mm long, with rear taper approx. 900 mm x 6° - Cargo area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg - TPMS (Tire Pressure Monitoring System) according to ECE R 141 - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle with trailing steering. 3rd axle with electromagnetic reverse lock via reverse gear and manual activation - Technical axle load: 12,000 kg each - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF twin tires. Brand of our choice, load index 143/141J (144/144F) - Mechanical landing legs with 2-speed gearbox and crank - Continuous grating flooring with approx. 5 mm steel plating for additional reinforcement, designed for point loads: on the lift bed and cargo area - Painted sand coating on the gooseneck cover plates as well as transition areas between neck and lift bed, lift bed and cargo area, and cargo area and ramps - 1 spare wheel mounting bracket under the cargo area to the right in front of the axles - Cut-outs in the outer frame of the cargo area and lift bed for attaching tie-down straps (LC 2,000 daN) - 11 pairs of recessed, fold-out lashing rings in the outer frame of the cargo area (LC 10,000 daN): 3 pairs in the lift bed outer frame, 8 pairs in the cargo area outer frame - 11 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 3 pairs in the lift bed, 8 pairs in the rear cargo area - Control valves for the hydraulic ramps located on the right side of the vehicle - 1 pair of foldable mechanical rear supports, single-hand operation HYDRAULIC LOADING RAMPS: - 1 pair of two-part AXS steel ramps, approx. 4,920 mm long, and a