Low loader semitrailer

FAYMONVILLE MAX Trailer MAX100 Semi-Tieflader

Condition: new, maximum load weight: 36,020 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our full vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Complete equipment details available on request. Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area with rear bevel approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) * 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate above the axles Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 3,185 + 1,420 x 1,250 mm, with grating covering C40/5 (point load approx. 2.8 t on a surface of approx. 20 x 20 cm) * Ramp with hydraulically foldable ramp sections and hydraulic lifting system * Maximum load per pair: 30,000 kg Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock activated via reverse gear and manually * Air suspension with raise/lower valve Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Brake system: * WABCO brake system compliant with EU regulations, with EBS-E (2S2M), without connection lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Kdjdpfxjy Auhue Ahbou Electrical system: * Electrical system according to EU regulations, LED lighting 24V ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to guarantee optimum corrosion protection * Finishing coat: 2 layers 2K topcoat, solid colour RAL 3002 carmine red as per RAL system 841GL * Rear section metallised and painted RAL 9010 (pure white) * Rims in silver Included accessories: * One bracket for warning signs on the gooseneck and at the rear left and right, including socket * 1 spare wheel holder under the loading area, right in the direction of travel * 2" kingpin * One galvanized steel front wall * Yellow-red air couplings on the galvanized front connection bar * 4 wheel chocks with brackets on the bulkhead * 3 height wooden boards * Galvanized folding supports under the loading area bevel * Bracket for rotating beacon at rear of trailer * Height-adjustable tarpaulin structure – approx. 3,960 mm * Galvanized front wall with tensioning system for sliding curtains, height adjustable by approx. 400 mm * EDSCHA roof, sliding forward on aluminum roof girder profiles (screwed to front and rear wall) * 3 pairs of sliding stakes in the loading area * The body is hydraulically extendable to the left and right at the rear by approx. 750 mm * Sliding roof with pivoting portal crossbeam * Sliding curtain with approx. 700 mm reserve length, ratchet straps at approx. 600 mm intervals. Height O

Condition: used, mileage: 1,057,000 km, Year of construction: 2000, Three-axle truck, 260 hp, equipped with a fixed body measuring 7.90 x 2.55 m and a rear hydraulic ramp, payload capacity of 12,050 kg, Bonfiglioli series 13,500 crane with 3 telescopic sections and remote control. Kodpfozyccfjx Ahbjdu Note: Please be advised that the vehicle description is indicative and may contain errors or inaccuracies. We therefore invite you to contact us to verify the accuracy of the data.

Condition: new, maximum load weight: 47,300 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately and at short notice, on our website. Excerpt from the equipment list. Full specifications available on request. Kodpsyvnfgsfx Ahbsdu Gooseneck: * Gooseneck with beveled front corners (approx. 45°) and rear bevel (approx. 750 mm x 10°) * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Extendable loading platform with rear bevel (approx. 1,000 mm x 8°) * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hooking tensioning straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick; over the axles, diamond plate surface Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, 24t lifting capacity (50t test load) Tyres: * 235/75 R 17.5 3PMSF tyres, brand at our discretion Axles: * BPW axles, two rigid axles, two trailing steering axles, air-suspended, with drum brakes, lifting/lowering function * Steering axles with electromagnetically-activated reverse lock (via reverse gear or manually) * Axle tools Brake system: * WABCO brake system in accordance with EU regulations with EBS-E (4S3M), no connecting lines to the tractor unit Steel structure: * Steel construction from high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield 355 MPa) S690QL/S700MC (yield 690 MPa) Electrical system: * Electrical system compliant with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets (ISO standard: 24N - ISO 1185, 24S - ISO 3731, 15-pin - ISO 12098) Paintwork: * Premium and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc-rich primer * High-quality 2-component (2K) single-color topcoat RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories: * Spare wheel holder in front of the bulkhead (without spare wheel) * 2 inch kingpin * Galvanized steel front wall approx. 400 mm high * Yellow-red air couplings on the galvanized front connection bar * Receptacle at the rear of the gooseneck for ALU loading ramps * Galvanized drop-down supports under the loading area bevel * Bracket for a revolving beacon at the rear of the trailer * Brackets left and right on the gooseneck and rear plate for warning signs including socket * TPMS tire pressure monitoring system compliant with ECE R 141 * Removable ALU sideboards and rear wall on the gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized insert posts are removable (body length approx. 2,560 mm) * Galvanized toolbox integrated in the beveled gooseneck * 3 pairs of WADER container locks in the loading platform for one 20' (30') or one 40' container * Sliding hook-in rails for ALU loading ramps at the rear of the vehicle * 6 pairs of pockets for plug-in posts, approx. 100 x 50 mm in the outer frame of the loading area * Galvanized extensions, extendable by approx. 230 mm per side * Lift axle on the front axle with TEBS E control based on current axle load and load status * 2 LED reversing lights mounted on the rear plate * 2 pairs of ferry-

Condition: new, maximum load weight: 36,410 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list: Complete equipment available upon request. Gooseneck * with angled front corners at approximately 45° and rear taper of approximately 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approximately 30 mm thick Loading Platform * Telescoping loading platform with rear taper of approximately 1,000 mm x 8° * 1 pair of fixed wheel recesses in front of the axles, approximately 2,850 x 970 x 400 mm (L x W x H) * Wheel recesses with square ladder rails approximately 15 x 15 mm, as well as widening in the lower area * A pair of fixed wheel recesses between the 1st and 2nd axles, approximately 1,610 x 970 x 400 mm (L x W x H) * Incl. 3-part removable galvanized covers over the wheel recesses (W approximately 670 mm), max. point load 5 t/piece. * Recess in the taper and extending into the loading platform to accommodate the excavator arm (approximately 2,900 x 750 x 210/290 mm (L x W x H)) * 1 pair of lashing rings lying horizontally at the front of the loading platform (LC 10,000 daN) * 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) Kjdpfxjz Sh H He Ahbedu * Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Two-part Steel Ramps * One pair of galvanized two-part steel ramps, approximately 2,750 + 1,400 x 800 mm, with hardwood flooring approximately 48 mm thick * Ramp with hydraulically extendable and foldable ramp sections and hydraulic lifting mechanism, hydraulically movable * Maximum load per pair: 40,000 kg * In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm do not need to be taken into account in the vehicle length when in the driving position. Kingpin Supports * JOST kingpin supports (mechanical) with a 2-speed gearbox for an approximate lifting capacity of 24 t (approximate test load 50 t) Axles * BPW axles and suspension, 2 axles fixed, 1 axle steerable * Technical axle load: 12,000 kg each * Electro-magnetic reverse locking system via reverse gear and manually activated Air Suspension * with lifting and lowering valve. Axle tool Tires * 235/75 R 17.5 3PMS – manufacturer of our choice * TPMS: TPMS tire pressure monitoring system in accordance with ECE R 141 * Data transmission to the tractor unit takes place via the standardized EBS interface according to ISO 11992 * For correct display, the tractor unit must be able to transmit and display this data Braking System * WABCO braking system according to EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Steel Construction * made of high-strength fine-grain steels. Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical System * in accordance with EU regulations * LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the turn signal * ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets * Connection according to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paint Finish * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Top coat with 2 layers of 2K topcoat, solid color in R

Condition: excellent (used), mileage: 349,000 km, power: 382 kW (519.37 HP), first registration: 09/2015, fuel type: diesel, fuel: diesel, brakes: retarder, color: white, gearing type: automatic, emission class: euro6, loading space length: 6,450 mm, loading space width: 2,550 mm, Equipment: central locking, retarder, trailer coupling, = Additional options and accessories = - Air suspension - Alloy wheels - Central lubrication - Coupling - Extra steering axle - Intarder - Low-noise - PTO - Reversing camera - Visor - Xenon lighting = More information = Year of construction: 2015 Empty weight: 23.345 kg Carrying capacity: 13.655 kg Kjdpfx Aheytr Ixobsdu GVW: 37.000 kg Make of bodywork: HMF 6020 K7 CE mark: yes Technical condition: very good Visual appearance: very good Price: On request

Condition: new, maximum load weight: 39,150 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list Complete equipment list available upon request. Equipment: * Gooseneck with beveled front corners at approximately 45° and rear bevel of approximately 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approximately 30 mm thick. Loading platform: * with rear bevel of approximately 1,000 mm x 8° * 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings, located horizontally at the front of the loading platform, for (LC 10,000 daN) * Recesses in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) * Hardwood flooring, approximately 48 mm thick, with diamond-plate flooring over the axles. Kingpin: * JOST kingpins (mechanical) with 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load) Axles: * BPW axles and suspension, 2 axles rigid, 1 axle with trailing arm steering * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated via reverse gear and manually Air suspension: * with lifting and lowering valve Tires: * 235/75 R 17.5 3PMSF – manufacturer of our choice * TPMS: TPMS tire pressure monitoring system according to ECE R 141 Braking system: * WABCO braking system according to EU regulations with EBS-E (2S2M) Steel construction: * made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical system: * according to EU regulations * Lighting: 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the turn signal * ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Painting: Kedpfxjz Rr R Sj Ahbedu * Complete steel construction automatically blasted with a shot blasting machine after welding * Second blasting with corundum for optimal adhesion of the coating system * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Final coating with 2 layers of 2K topcoat, solid color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) * Metallic paint not possible * Paint build tested in a salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Incl. the following additional equipment: * 2-inch kingpin * One galvanized steel front bulkhead, approximately 400 mm high * A spare wheel holder in front of the bulkhead * Mounting rail for aluminum loading ramps on the gooseneck with integrated impact protection (± 56 kg) * Galvanized folding supports under the bevel of the loading platform * A mounting bracket for a rotating beacon on the rear of the trailer * On the gooseneck and rear panel, on the left and right, a mounting bracket for warning signs including socket * Load indicator to determine the axle loads including load diagram * 1 pair of recessed lashing rings along the center beam at the rear in the bevel (LC 10,000 daN) * Additional fastening option for the license plate of the trailer at the rear right of the trailer Incl. special accessories: * Aluminum sideboards and rear panel on the gooseneck, pluggable, approximately 2,440 x 400 mm (L x H) * The rear galvan

Condition: new, maximum load weight: 40,320 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Below is an excerpt of the features. Complete equipment list available upon request. GOOSENECK Gooseneck with a rear slope of approximately 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood decking approximately 30 mm thick. - 2-inch kingpin - Yellow-red air couplings on the galvanized connection bar at the front. Kdsdpez N Nx Rsfx Ahbju - 4 wheel chocks with holder on the front wall (± 5 kg). LOADING AREA 5 pairs of lashing rings that fold outwards (LC 5,000 daN). 3 pairs of lashing rings that fold outwards (LC 10,000 daN). 1 pair of lashing rings lying at the front in the loading area (LC 10,000 daN). Hardwood decking approximately 48 mm thick, with diamond plate decking over the axles. - On the gooseneck and at the rear, left and right, one holder each for the warning signs, including a socket. - A galvanized steel front wall. - 3 height-adjustable wooden planks. - Galvanized folding supports under the slope of the loading area. - A holder for a rotating beacon at the rear of the semi-trailer. - Height-adjustable tarpaulin superstructure, approximately 3,960 mm. - Galvanized front wall with a tensioning mechanism for the sliding curtains. - Height-adjustable by approximately 400 mm. - Roof from the EDSCHA brand, which can be moved forward on aluminum roof rail profiles. - 3 pairs of sliding rails in the loading area. - The superstructure can be hydraulically widened at the rear to the left and right by approximately 750 mm (for loading and unloading). - Sliding cover with a pivoting portal beam. - Sliding tarpaulin with approximately 700 mm of reserve in length, with tension straps at intervals of approximately 600 mm. - Height of the top edge of the superstructure approximately 3,960 mm (loaded). - Driving with the sliding cover open is not permitted and will damage the tarpaulin. - Attachment rail for aluminum ramps at the rear of the vehicle. - Control valves for the hydraulic widening of the superstructure, mounted on the right side of the semi-trailer. (± 4 kg) - White reflector tape according to EU regulations, red on the sides and rear. - Electro-hydraulic unit at the rear under the loading area. (± 45 kg) - Holder for a pair of warning signs on the front wall. - Four warning signs, approximately 400 mm extendable, approximately 423 x 423 mm, with an LED position light (± 25 kg). - On the warning signs, a holder for a rotating beacon. - 7 pairs of rail pockets for plug-in rails, approximately 100 x 50 mm, in the outer frame of the loading area (± 21 kg) - Lift axle on the front axle, controlled by TEBS-E depending on the current axle load and loading condition (± 69 kg). - 6 pairs of recessed lashing rings along the central beam (LC 5,000 daN). - 1 pair of recessed lashing rings along the central beam at the rear (LC 10,000 daN). (± 27 kg) - A painted layer of sand on the diamond plate on the gooseneck and in the loading area as anti-slip protection. - 1 LED reversing light, each on the left and right, in front of the first axle. - 2 LED work lights mounted on the rear panel. - An acoustic warning signal when reversing. ACCESSORIES - Cable for supplying the electro-hydraulic unit and/or the electric winch (approximately 35 mm², approximately 3.5 m long, max. 250A) between the semi-trailer and the tractor unit with a plug connection (NATO-NATO). FIFTH WHEEL BRACKETS JOST fifth wheel brackets, mechanical, with a 2-spee