Low loader

Faymonville MAX 510

Condition: used, maximum load weight: 30,660 kg, overall weight: 43,000 kg, axle configuration: 2 axles, first registration: 03/2024, next inspection (TÜV): 03/2025, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment: Complete equipment available upon request. Loading Platform * Low-bed with central beam in extendable design * Length approx. 6,750 mm * 5 pairs of lashing rings that fold outwards (LC 5,000 daN) * 1 pair of lashing rings that fold outwards (LC 10,000 daN) * 1 pair of lashing rings lying horizontally at the rear of the loading platform (LC 10,000 daN) * The supply lines are protected in the central beam and adapt to the respective low-bed length. Gooseneck * Length approx. 3,900 mm * Gooseneck hydraulically adjustable up/down and extendable * Technical saddle load: 23,000 kg Rear Chassis * Short design with closed outer frame and diamond plate cover * Chassis with excavator well, which is closed in the rear half to accommodate the air tanks * 2 pairs of lashing rings that fold outwards (LC 5,000 daN) * 1 pair of lashing rings that fold outwards (LC 10,000 daN) Axles * BPW axles * Hydro-mechanically forced steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Axle tool Tires * 245/70 R 17.5 3PMSF – Manufacturer of our choice, load index (146/146F) Tedpfezvt Tyjx Acnsb Braking System * According to EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork * High-quality 2-component (2K) * Topcoat in solid color RAL 3002 carmine red Incl. the following additional equipment: * 2-inch kingpin * One galvanized steel front wall, approx. 400 mm high * One spare wheel holder in front of the front wall * Yellow-red air couplings on the galvanized connection strip at the front * 4 wheel chocks with bracket. (± 5 kg) * Steering from the front and rear via cable remote control, operable via push buttons, with single-axle steering control (without installation in the tractor unit) * Electro-hydraulic unit (± 45 kg) * Yellow reflector tape according to EU regulations on the side, on the extension, and at the rear of the trailer * 1 wooden block, approx. 500x250x200 mm * Attachment rail for aluminum loading ramps at the rear of the vehicle * One bracket for a rotating beacon at the rear of the trailer * One mud flap at the rear of the trailer * European reflector plates (red-yellow) at the rear of the trailer * On the gooseneck and at the rear panel, one bracket each on the left and right for warning signs including socket * Manual and description on a USB stick * Speed stickers 80 km/h at the rear and on both sides * Load gauge for determining axle loads including load diagram * Incl. special accessories: On the gooseneck, aluminum side and rear walls, plug-in, approx. 2,440 x 400 mm (L x H) * The rear galvanized end crossbars are removable. (Length of the structure approx. 2,560 mm). (± 46 kg) * On the gooseneck, a separate air connection with an air gun. * 2 work lights with a switch on the trailer, mounted on the gooseneck platform on the left and right * 6 pairs of rung pockets for end crossbars approx. 100 x 50 mm in the outer frame of the loading platform * 2 pairs in the outer frame of the chassis (± 29 kg) * Extensions, galvanized, extendable by approx. 230 mm per side (± 262 kg) * Hydraulic connections from the gooseneck to the low-bed with multi-coupling instead of screw co

Condition: good (used), Year of construction: 2011, Load moving system CBM 240 / ST 120 MACH-ID 923 Tedpfowvhrtex Acnob Type: CBM 240 / ST 120 Year: 2011

Condition: used, maximum load weight: 25,630 kg, overall weight: 38,000 kg, axle configuration: 2 axles, first registration: 11/2024, next inspection (TÜV): 11/2026, Equipment: ABS,

Condition: new, maximum load weight: 30,190 kg, overall weight: 43,000 kg, axle configuration: 2 axles, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Full equipment details available on request. Loading Platform: - Lowbed with external beams in extendable SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking mechanism - Supply lines protected inside the extendable side rails, automatically adjusting to the current bed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for attaching RUD screw-on rings Gooseneck: - Gooseneck in SNT design for optimized platform length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractors: 4x2, 6x2 Rear Chassis: - Rear chassis in short version with closed external frame and checker plate cover - Running gear with excavator recess, closed in the rear half to accommodate the air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings horizontal, front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Technical axle load per axle: 12,000 kg - Air suspension with lift and lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF - Manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transmission to the truck via the standardized EBS interface in accordance with ISO 11992 - The truck must be capable of processing and displaying this data for correct operation Braking System: - Braking system according to EU regulations with EBS-E (2S2M) Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with indicators - ASPÖCK-UNIBOX at the front connection point with 24N, 24S, and 15-pin sockets as per standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel Construction: - Steel construction from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure is automatically shot-blasted after welding using a blasting turbine system - Second blasting process with corundum for optimal adhesion of coating system - HRM metallization of complete chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection - Final paint finish with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, as per RAL system 841GL - Rims in silver - Rear section metallized and painted RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test as per ISO 9227-NSS - Cavities sealed with special wax Including the following additional equipment: - 2" King pin - One galvanized steel front wall, approx. 400 mm high - Remote steering of front and rear axles by cable remote control with pushbuttons, including single track axle monitoring (without installation in the tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Electro-hydraulic power pack - Preparation for mounting container locks for 1x 20' or 1x 40' container on the external beams Tedoxarl Nopfx Acnjb - Without container locks

Condition: excellent (used), Year of construction: 2023, roll diameter: 85 mm, total width: 800 mm, total height: 650 mm, total length: 1,200 mm, empty load weight: 150 kg, Load moving system CS Skates - ET6 Todpfx Acjzcvbzonsb MACH-ID 7822 Make: CS Skates Type: ET6 Year: 2023 Steering skate length:600mm Steering skate width:530mm Steering skate hight:110mm Skate length: 270mm Skate width: 220mm Skate hight: 110mm Max. loading capacity:3 + 6T Number of wheels: 16 Wheel Ø: 85mm Wheel material: Hard Nylon Hydraulic jacks: 2 Lifting capacity: 10T Lifting range of foot:30-260mm Lifting range of head:420-650mm Length: 1200mm Width: 800mm Height: 650mm Weight: 150kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Excerpt from equipment specification. Complete specification available on request. Load area: - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Including the following additional equipment: Tedpfx Ajxf Silscneb - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation)

Condition: new, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Technical Data MAX510-Z-2H-ATX-A-6.85-PA Speed: 80 km/h Total weight: 47,000 kg Saddle load: 23,000 kg Axle load: 24,000 kg Gooseneck length: 3750 mm Saddle height loaded: 1200 mm Rear overhang: 2300 mm Loading area length: 6,850 mm Extendable by: 5,500 mm Loading height at max. load: 350 mm Frame length: 2,600 mm Loading height, rear frame at max. load approx.: 1,005 mm Suspension travel: -150/+450 mm Axle track: 1360 mm Overall width: 2,540 mm Total weight depends on the saddle load. Low-bed: Low-bed with external, extendable beams. "SUPER LOW" design, length approx. 6,850 mm. Low-bed with fixed hardwood floor, approx. 40 mm thick, and mechanical locking mechanism. The supply lines are protected in the extendable beams and automatically adjust to the respective low-bed length. 5 pairs of lashing rings, foldable outwards (LC 10,000 daN). 6 pairs of threaded blocks on the inner beam for mounting screwable RUD rings. Rear frame: Rear frame with closed outer frame, diamond-plate flooring and continuous prism-shaped excavator well, approx. 1,250/700 x 505 mm, open at the rear. 2 pairs of lashing rings, foldable outwards (LC 10,000 daN). 1 pair of lashing rings lying in the well (LC 8,000 daN + 5,300 daN). 2 pairs of stake pockets for stake pockets 100 x 50 mm in the outer frame. Gooseneck: Gooseneck in SNT design for optimizing the loading area length, length approx. 3,785 mm. Gooseneck hydraulically adjustable up/down and extendable. Technical saddle load: 23,000 kg For semi-trailer tractor: 4x2, 6x2 and 6x4 PENDULUM AXLE: "PENDULUM AXLE", all axles hydro-mechanically forced steered. Hose burst valve on the axle compensation cylinder with automatic RESET function. Hydraulic cylinders with shut-off valves and quick-release coupling for securing in the raised position. Final coating of the axles with 2 layers of 2-component paint, solid color in "FAY-Gray-34-0260". Technical axle load: 12,000 kg Hydraulic axle equalization. Todeizu Nwspfx Acnsb Axle tool. Braking system: Braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the semi-trailer tractor. Electrical system: Electrical system according to EU regulations, lighting 24 volts ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection bar with sockets 24N, 24S & 15-pin. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: Steel construction made of high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (Yield strength 355MPa) S690QL/S700MC (Yield strength 690MPa) Painting: First-class and durable corrosion protection of the standard shot-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat, solid color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (Pure White). Metallic paint not possible. Tires: Tires 245/70 R 17.5 3PMSF At the manufacturer's option. Load index (146/146F) Preparation for mounting screwable container positioning for 1 x 20' or 1 x 40' container on the outer beams. Without container locking mechanisms. i i2" Kingpin iA galvanized steel front wall, approx. 400 mm high. iA spare wheel with holder in front of the front wall. i2 pieces of wheel chocks with holder on the front wall. iYellow-red air couplings on the galvanized front connection bar. Steering from the front and rear by means of a cable remote control via push buttons, with single-axle control. (without installation in the semi-trailer tractor) i Hydrauli

Condition: used, Year of construction: 2011, Extendable superstructure: Yes Please contact Theo Lelie for more information Tjdpfszl Exgox Acneb

Condition: new, maximum load weight: 34,104 kg, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Further information here: Tjdpfx Ajv D Abgocneb

Condition: excellent (used), functionality: fully functional, empty load weight: 2,620 kg, overall weight: 18,000 kg, first registration: 01/2017, suspension: air, Year of construction: 2017, WEB ANH 18 / Interchangeable Chassis / BDF • Manufacturer: WEB • Type: ANH 18 • Year of manufacture: 01/10/2017 • Suspension: Air/Air • Unladen weight: 2620 kg • Payload: 15380 kg • Permissible total weight: 18000 kg • 5.95 meter container • 40 mm drawbar • Next inspection: 08/2026 • German machine • Immediately ready for operation • This offer is non-binding and subject to change. - Subject to prior sale, Tjdpfx Aezdt Exocnob - Errors and/or typographical errors cannot be ruled out. - Sale subject to our general terms and conditions.