Mesh welder

EVG TSD 7-25

Condition: excellent (used), Year of construction: 1995, Combination Unit: Manufacturer: GSG Feeder: Type: 840.02-027 Crusher Descaler: Type: 663.02-017 Wire Range: Ø5.5-16mm For wire rod with approx. 40-60 daN/mm² strength Crushing and Bending Rollers: Carbide Inserts Adjustment with 0.37 kW - 1.15 A gear motor Brush Drive with 0.25 kW gear motor, n=293 rpm Connection Voltage: 380-420 V 50 Hz Dry Coating Unit: Type: BSG/T Filling: Calcium Stearate (e.g., Traxit Type: D S 51 E) Stearate Consumption: approx. 350 g per t of wire Drawing Speed: max. 15 m/s Electrical Power: 2x 0.55 kW gear motors Cassette: 2 slots (supplied with 1x roller block + 1x cassette) Type: PKG/T (TS) Cleaned rolled wire Wire strength approx. 40–60 daN/mm² Wire range max. inlet diameter 9.5mm, finished diameter 3.5–8.5mm Roll dimensions min. Ø115mm, max. Ø125mm, Bore diameter Ø82mm, width 15–25mm Cooling pin diameter 25mm Cooling water consumption approx. 600 l/h Drawing machine: Manufacturer: Koch Type: KHZ 5000 Year of manufacture: 1993 Serial number: 13.821 Number of draws: 1 draw per block Drawing drum: Ø700mm Tensile force: mechanical 5000 N Wire material: mild steel wires Run-in strength: approx. 40 – 45 daN/mm² Maximum drawing range: Inlet diameter 5.0 – 8.5mm Cross-section reduction: 20 x 25% (mechanical gradation) Drawing speed: up to max. 7.0 m/s Brake: Twiflex, type: MRB Drive: AC motor/frequency converter, Siemens Rcjdpfx Asr Nfvmsmyed PN=110 kW, n=1485 rpm Spooler: Manufacturer: Koch Type: KHS 1250 Year of manufacture: 1993 Factory No.: 13741 Wire diameter: 5 – 8.5 mm Strength: approx. 55 – 70 daN/mm² Winding speed: V=7 m/s, adapted to the drawing machine Filling weight: approx. 3000 kg Spool drive motor: Three-phase motor with external fan Type: 1 PQ 6253 – 6 AA 70- Z A 15 + K 20 + C 14 + H 46 P=37 kW, n=1000-2000 rpm, IP54, design B3 Laying drive motor: 66-671U, 1.5 kW, 170 V, 9.8 A, 1680 rpm, IP 44, B5-200 With Attached tachometer generator TG 20, 20 V / 1000 rpm With attached spur gear SK 32, i=57.53, design B6 Hydraulics: Hydraulic excavator type: H13 AK Pneumatics: Twiflex disc brake type: MRB Pneumatic cylinder type: SPWG 28032-25mm stroke Dimensions: 3100 x 3000 x 1700 mm (L x W x H) without counterweight

Condition: new, Working width: 4010 mm Bending capacity (St42): 2.0 mm Bending angle adjustment from/to: 0 - 135° Adjustability of the bending beam: 25 mm Hydraulic motor drive power: 2.2 kW Weight, approx.: 5000 kg Dimensions LxWxH, approx.: 5600 x 1750 x 2050 mm The torsion-free, heavy machine body is designed for very high loads. This machine therefore guarantees a high and consistent quality of your bent products. The integrated tool holder makes it easy to change tools. This means that the AKB folding machine can be easily adapted to your future requirements. Model description: - MIKRA Bending Control positioning control type "M15S" (alternative control variants optionally available) - Solid and torsion-free welded steel construction - Bending beam adjustment from 0 to 135 - Hydraulically driven upper and bending beam - Clamping pressure of the upper beam can be adjusted centrally from the front on both sides - Crowning of upper, lower and bending beam manually adjustable - Segmented upper beam / upper beam inclination 45° Scope of delivery: - Manual backgauge 600 mm Rjdep Dufzopfx Amyecd - Tool set: Segmented upper tool Lower beam rail Bending beam rail 25.0 mm - Manual gap adjustment - 3-way foot switch - Control valve for setting the hydraulic pressure from the front - Foot pedal with three functions, handle and emergency stop button - Light barrier - Oil filling - Documentation - CE

Condition: used, travel distance X-axis: 7,000 mm, travel distance Y-axis: 4,000 mm, travel distance Z-axis: 900 mm, spindle speed (max.): 1,200 rpm, feed rate X-axis: 900 m/min, Ø quill: mm. 140 Spindle taper : ISO 50 travel X : mm. 7000 travel Y: mm. 4000 Cross travel Z RAM: mm. 900 Quill travel W: mm. 900 Rotary table: mm. 1800x1800 load admitted on table: Ton. 10 Table rotation: °.pos. Table long.travel (AxisV): mm. 1500 Spindle speed : RPM. 1200 Spindle motor: Kw. 70 CNC ECS 2101 Rcedpfot Rkcuex Amyed N°2 milling square heads N.2 Floor plate 6000x2000

Condition: good (used), Year of construction: 2008, functionality: fully functional, Okuma Multus B300-W 6-axis turning and milling center - Okuma OSP P200L - Year 2008 - Cutting time: 10,500 h - H1 milling spindle: 6,000 rpm Rjdpjyg Rf Nefx Amyecd - Main spindle: 3,800 rpm, Rota NC 315-86 - Counter spindle: 5,000 rpm - ATC 60 system HSKA-63 (60 tools) - Geometry: very good - Marpos tool sensor

Condition: reconditioned (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: M-900iA/260L R-30iA, load capacity: 260 kg, arm reach: 3,100 mm, controller manufacturer: Fanuc, controller model: R-30iA, teach pendant manufacturer: Fanuc, Equipment: documentation/manual, IRS Robotics®: Refurbished industrial robot. Reliability as standard. 100% complete and fully functional: robot arm, controller, all cabling, and teach pendant. Includes our warranty and a detailed 77-Point Protocol evaluation performed by our in-house robotics engineers. Brand: FANUC Type: M-900iA/260L Controller: R-30iA Payload: 260 kg Reach: 3.1 m Rcsdpfxsp T Umqe Amyed General purpose: Heavy-duty, long-reach robot Robot mass: 1800 kg Delivery time: To be agreed upon mutually IRS Robotics® refurbished: 77-Point Protocol – fully tested on our test benches, new oil/grease, new batteries, fully cleaned, painted in your desired RAL color. Includes Accuracy Status Measurements (repeatability, accuracy, backlash) About: Our core business is the reliable delivery of refurbished A-brand robots: ABB – KUKA – ABB – YASKAWA. Established in 2002. We ship worldwide!

Condition: excellent (used), Year of construction: 1996, spindle bore: 160 mm, Swing over bed Ø 1040 mm Swing over cross slide Ø 710 mm Rodpfx Amoxtbf Eeyecd Swing in the gap Ø 1580 mm DBC Turning Length 3000/4500 mm Gap length 1500 mm Spindle bore 160 mm Spindle power 40 kW Bed width 800 mm Spindle taper 6 Mk Workpiece weight 3500 Speeds / ranges 800 Rpm Feed rate X-Axis 10000 mm/min. Feed rate Z-Axis 10000 mm/min. Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 2024, condition: new, Motorized sheet metal shear Technical data Cutting capacity: 2.5 mm Cutting length: 2550 mm Cutting angle: 1°40′ Stroke rate/min: 35 1/sec Motor power: 3 kW Back gauge range: 550 mm Table width: 400 mm Table height: 850 mm Height: 1260 mm Width: 1350 mm Length: 3100 mm Weight approx.: 1540 kg Rcedpfx Amshk Nf Rsysd

Condition: used, TECHNICAL DETAILS - Number of axes : 10 - Number of spindles : 2 MAIN SPINDLE - Max. bar diameter : 32 [mm] - Travel : 240 [mm] - Spindle speeds : 8000 [rpm] - Spindle power : 7.5 [kW] - C axis indexing precision : 0.1 [°] COUNTER-SPINDLE - Max. bar diameter : 32 [mm] - Spindle speeds : 6000 [rpm] GUIDE BUSH HOLDER 1 - Number of positions : 5 GUIDE BUSH HOLDER 2 - Number of positions : 5 - Number of motorized positions : 4 - Live tools speed : 6000 [rpm] END ATTACHMENT - Number of positions : 4 - Number of motorized positions : 4 - Live tools speed : 6000 [rpm] SECONDARY OPERATION - Number of positions : 7 - Number of motorized positions : 3 - Live tools speed : 6000 [rpm] POWER SUPPLY - Supply voltage : 400 [V] MACHINE HOURS - Number of working hours : 56.433 [h] Redpfxsuhax Es Amyscd EQUIPMENT - CNC : Fanuc - Rotating tool motor on : S2,S3,S5 V+H - Rotating guide bush - Parts catcher - Ejection of workpiece - Chips conveyor - Coolant tank * with high-pressure pump - Number of turning tool holders : 3 - Number of fixed tool holders : 7

Condition: used, Year of construction: 2008, turning diameter: 275 mm, spindle bore: 80 mm, spindle speed (max.): 4,000 rpm, travel distance X-axis: 260 mm, travel distance Z-axis: 1,345 mm, total height: 2,232 mm, total length: 4,339 mm, total width: 2,232 mm, overall weight: 7,600 kg, Equipment: documentation/manual, CNC Lathe with Y-axis, driven tools an 2nd spindle CNC Control MSX-850-lll (mitsubishi 720 BM) Turning diameter 275 / 366 mm Spindle bore diameter 80 mm Spindle speed 4000 R/min Spindle motor 18.5/15 Kw Movement X-axis 260 mm Movement Y-axis +50 / -50 mm Movement Z-axis 1345 mm Movement W-axis (subspindle to mainspindle) 1275 mm Min indexing C-axis main spindle 0,001 ° Number of tools on turret 12x Number of driven tools 12 x Tool Taper BMT Bar feeder LNS Quick Load Servo lll Spindle motor driven tools 6000 R/min Rcedpjy Nyzgjfx Amyed If you have any questions concerning the machine, please do not hesitate to contact us by phone or e-mail. Feel free to view our other advertisements for a complete overview of our stock.

Condition: used, TECHNICAL DETAILS - Number of axes : 10 - Number of spindles : 2 MAIN SPINDLE - Max. bar diameter : 25.4 [mm] - Max. machining length : 200 [mm] - Spindle speeds : 10000 [rpm] - C axis indexing precision : 0.1 [°] COUNTER-SPINDLE - Max. bar diameter : 20 [mm] - Spindle speeds : 10000 [rpm] - Spindle power : 3.7 [kW] - C axis indexing precision : 0.1 [°] - Number of guide bush holders : 2 GUIDE BUSH HOLDER 1 - Number of positions : 5 GUIDE BUSH HOLDER 2 - Number of positions : 5 - Number of motorized positions : 4 Rcedpfx Aouha Ugomyjd - Live tools speed : 8000 [rpm] END ATTACHMENT - Number of positions : 4 - Number of motorized positions : 4 - Live tools speed : 6000 [rpm] SECONDARY OPERATION - Number of positions : 7 - Number of motorized positions : 3 - Live tools speed : 8000 [rpm] POWER SUPPLY - Supply voltage : 400 [V] - Total installed power : 14 [kW] WEIGHT & DIMENSIONS - Machine floor space : 2270 x 1650 [mm] - Machine height : 2200 [mm] - Machine weight : 3500 [kg] MACHINE HOURS - Number of working hours : 80490 [h] EQUIPMENT - CNC : Fanuc - Rotating tool motor on : S2,S3,S5,S6 - Rotating guide bush - Parts catcher - Ejection of workpiece - Chips conveyor - Coolant tank * with high-pressure pump - Bar loader : ROBOBAR SBF 532 - Oil mist extractor - Cooling unit