Electric forklift 3t lithium ion

EP CPD30L1-S

Condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: 1321500165, Year of construction: 2023, operating hours: 10 h, load capacity: 3,000 kg, lifting height: 4,800 mm, free lift: 1,520 mm, load center: 500 mm, fuel type: electric, mast type: triplex, construction height: 2,225 mm, power: 24 kW (32.63 HP), gearing type: automatic, battery capacity: 560 Ah, battery voltage: 80 V, DGUV certified until: 08/2025, fork carriage width: 1,228 mm, fork length: 1,070 mm, overall weight: 4,830 kg, total height: 4,095 mm, total length: 3,640 mm, total width: 1,298 mm, color: original, Equipment: cabin, lighting, sideshift, Technical data: Type: EP CPD30L1 (S) Load capacity: 3000 kg Load center of gravity: 500 mm Forks: on request Drive: electric Lifting mast: Triplex‑4,800mm Equipment: Full cabin with heating Side shift and fork adjustment Non-marking SE tires LED headlights Bluespot Warning lights Cedsvmyz Njpfx Ab Tohf Display Lifting height: 4800 mm Height: 2225 mm Free lift without/with LSG: 1520 mm/ 1130 mm Battery: 80V/560AH Li-ion (large battery) Charger: 80V/200A Application: The L1 series is more powerful than many competitors thanks to the built-in Li-ion technology. With their waterproof design, these forklifts can be used outdoors, even in the rain. They are particularly effective when loading and unloading loads. Features: Revolutionary Li-Ion technology: The L1 series is considered the world's first true Li-Ion forklift. By eliminating combustion engines and bulky lead-acid batteries, the truck has been designed from the ground up with ergonomics and performance in mind. Fast charging and high performance: The compact size of the battery allows for optimized truck sizing for maximum stability and safety. The L1 forklift can be charged in just 2.5 hours and offers the impressive ability to take up to 7% of charge in just 10 minutes. Waterproof design (IP54): All L1 series forklifts are water and dust resistant to IP54. This waterproof design allows for outdoor use, even in adverse weather conditions, which is not possible for many electric forklifts. AC motor performance improvement: The optimized 20L1S now has all AC motors, resulting in increased performance. This increases the efficiency and performance of the forklift. Large cabin with maximum legroom: Thanks to the completely redesigned chassis, the L1 forklift offers the most legroom in the industry. The compact battery creates sufficient space for the drivers' legs, which significantly improves driver comfort during long work shifts.

Condition: used, Year of construction: 2014, Number of spindles 5 St. Working width 230 mm Working height 120 mm Length of the planing table 2500 mm Feed motor 4 kW Feed speed 5-30 m/min. Control Memory-Funktion Weinig Powermat 600 Compact ----- The machine will be cleaned and completely checked before delivery. Brief Summary: ----- - 5 spindles - Powerful motors - Left and upper spindles controlled for width and height Detailed Description: ----- Technical Specifications: Working width: 20-230 mm Working height: 10-120 mm Number of spindles: 5 1st spindle - bottom ----- Motor with brake: 7.5 kW Spindle diameter: 40 mm Speed: 6,000 rpm Tool travel radius: 125-145 mm Tool travel radius for rebate cutter: 130-160 mm Axis adjustment range: 5 mm Rebate device MarathonCoatin for table insert in front of the 1st lower tool holder Electronic digital display for wheel adjustment Chsdowzmu Rspfx Ab Tsf 2nd spindle - Right ----- Motor with brake: 11.0 kW Shared motor with left-hand tool holder Spindle diameter: 40 mm Speed: 6,000 rpm Tool cutting radius 40 mm below table level: 93 - 200 mm Tool cutting radius 55 mm below table level: 93 - 180 mm Tool cutting radius for straight cutter heads max. 163 mm Max. tool diameter behind stop level: 180 mm Max. throat depth: 35 mm Axis adjustment range: 55 mm 3rd spindle - left ----- Motor with brake: Shared motor with the 2nd spindle Spindle diameter: 40 mm Speed: 6,000 rpm Tool cutting radius 40 mm below table level: 93 - 200 mm Tool cutting radius 55 mm below table level: 93 - 180 mm Tool cutting circle for straight cutter heads max. 163 mm Max. throat depth: 35 mm Axial adjustment range: 55 mm Radial CNC-controlled spindle 4th spindle - top ----- Motor with brake: 11.0 kW Spindle diameter: 40 mm Speed: 6,000 rpm Tool cutting circle: 93 - 200 mm Tool cutting circle for straight cutter heads max.: 180 mm Max. throat depth: 35 mm Axial adjustment range: 40 mm Radial CNC-controlled spindle Split pressure shoe in front of the upper tool holder, adjustable to the tool cutting circle and pivoting away from the tool, spring-loaded. Pressure shoe before and discharge after the upper spindle with electronic digital displays, integrated into the memory function. 5th spindle - lower ----- Motor with brake: 7.5 kW Spindle diameter: 40 mm Speed: 6,000 rpm Tool cutting radius: 93 - 200 mm Max. groove depth: 15 mm Axis adjustment range: 35 mm Feed system ----- Electronic feed, continuously adjustable with brake: 4 kW, 5 - 30 m/min Feed roller in front of the first lower tool, pneumatically controlled up/down. Durofer pointed tooth rollers with depth gauge and self-cleaning. Adjustment range of the feed rollers relative to the left tool holder, axial: 35 mm Machine electrical system ----- Operating voltage 400 V (voltage range 380 - 420 V), 50 Hz. All spindles are IE 2 version. Electrical design according to DIN VDE 0113, electrical equipment for industrial machines EN60204, IEC-204-1. Other electrical regulations are not taken into account. Machine stands, tables, and stops -----...

Condition: ready for operation (used), functionality: fully functional, working width: 260 mm, planing height: 170 mm, spindle diameter: 40 mm, planing width: 260 mm, working height: 170 mm, power of feed motor: 4,000 W, spindle speed (max.): 6,000 rpm, spindle speed (min.): 6,000 rpm, height adjustment type: electric, number of spindles: 5, input frequency: 50 Hz, Equipment: cabin, motor brake, Weinig Profimat 23 E Working width: 260 mm, working height: 170 mm, 5 spindles, spindle diameter: 40 mm, Spindle arrangement: 1- Bottom - 5.5 kW 2- Right + 3- Left - 11 kW 4- Top - 5.5 kW 5- Bottom - 11 kW Feed rate: 6 - 24 m/min - 4 kW Air cushion in the table One driven roller in the table at the exit. With tool. Chedpfx Absvgnb Ro Tef

Condition: used, Weinig Powermat 700 planer and moulder with CNC control for four-sided planing and profiling of wood. Available by arrangement from March 2026. Sale of this machine is subject to the sale of the briquetting press (Ref. No. 800055) or the entire planing unit (Ref. No. 100101). spindle: 6 spindle 1: Bottom / 7.5 kW / 6,000 rpm spindle 2: Right / 15 kW / 8,000 rpm Chodexpuufjpfx Ab Tef spindle 3: Left / Common motor with #2 / 8,000 rpm spindle 4: Top / 11 kW / 8,000 rpm spindle 5: Top / 7.5 kW / 8,000 rpm spindle 6: Bottom / 7.5 kW / 8,000 rpm working width: 230 mm working height: 160 mm spindle diameter: 40 mm feed: 40 m/min / 5 kW Planer table length: 1.200 mm Control: Memory Plus

Condition: used, Year of construction: 2004, machine/vehicle number: P 04-09-002, neu U05 10 001, Spraying machine Venjakob VEN SPRAY-K All pictures only for example - Producer Venjakob - Year of construction 2004 - Current condition: not refurbished - Offer price for refurbished condition - Working width 800 mm (1000) mm - Operating side, right - Duo gun drive system - Dry filter system 4.000 m³/Std. - Diameter exhaust air pipe 400 mm - Transport belttransport System - Feed speed adjustable 3 - 8 m/min - Lacquer reclaiming system with v-belt - Gun control system LS 1 - Number of installed lacquer circles 1 Stk. - Airless spraying system 4 Stk. Krautzberger KAA 1300 Chjdoumvr Topfx Ab Tjf - Number of lacquer pumps 1 Stk. - Producer lacquer pump Wagner 35-70 - Suitably for solvent based lacquer - Suitably for water based lacquer - Total connection power 7 kW, Stromaufnahme 17 A , Absicherung 35 A - Location, on stock - Voltage fluctuation max. +/- 5 % _____ Optionally, we can also provide you with a quotation for the assembly and start-up of the system, as well as training for your employees. We also offer regular maintenance and servicing of the machine on request. For further information, get in touch with us!

Year of construction: 2025, condition: new, Rollers: 4 Roller width: 60 mm Roller diameter: 120 mm Spring travel: 20 mm Speeds: Variable 3 - 18 m/min. Stand: Stand 1050 plus Cedeg Ez Sijpfx Ab Tshf Motor power: 0.75 kW

Condition: excellent (used), Year of construction: 2003, Veneer Composing Machine Electric motor, separate for chains and glue application Glue is applied to the edge of the newly inserted veneer strip, which increases the strength of the glue joint. Robust, durable stainless steel conveyor chain with flexure joints Separate controls for temperature, speed, and pressure Quick and easily accessible glue tank for fast and convenient refilling or cleaning Multiple heating zones for individual temperature adjustment Extended glue tank lifetime due to integrated cooling unit Continuously adjustable feed speed INCLUDES GLUE COOLER Technical Data: Throat depth: 1200 mm Veneer strip width: 45–1200 mm Veneer strip length: 300–3200 mm Veneer strip thickness: 0.4 – 3.0 mm Veneer moisture content: max. 8–12 % Working height: 900 mm Feed speed: 5–50 m/min Heating zone length: 1000 mm Max. heating temperature: 250 °C Electrical connection: 9.0 kW, 400 V, 50 Hz Compressed air: 6 bar Chodpoxgg Hhsfx Ab Tef Dimensions (L x W x H): 2400 x 2300 x 1900 mm Weight: 1500 kg SPARE PARTS VALUED AT EUR 3,500 HAVE BEEN INSTALLED

Condition: used, Number of spindles 5 St. Working width 20 - 230 mm Working height 8 - 120 mm Csdewugpbepfx Ab Tshf Length of the planing table 2000 mm Feed motor 1,1 kW Feed speed stufenlos regelbar 2 - 12 m/min. 1 WEINIG VARIOMAT planer and moulder including multifunction / slotting table ----- Machine will be cleaned and functionally tested before delivery ! Technical manufacturer's description: ----- Working width: 20 - 230 mm Working height: 8 - 120 mm 1st spindle horizontal, bottom ----- Motor with brake: 5.5 kW Diameter 40 mm Speed ??6000 rpm Tool radius 125 - 145 mm Axis adjustment range 5 mm Folding device including rebate cutter MarathonCoating for table insert before and after the 1st lower spindle 2nd spindle vertical, right ----- Motor with brake: 11 kW Common motor with left vertical spindle Diameter 40 mm mm Speed ??electronically adjustable 3000 - 6000 rpm (for 11 kW/15 HP) Tool cutting radius for longitudinal machining 93-232 mm Minimum tool diameter at stop plane: 93 mm Maximum tool diameter behind stop plane: 180 mm Maximum throat depth 45 mm Axially adjustable travel 30 mm Insertion segment, including additional stop lip 125 mm Insertion segment, including additional stop lip 150 mm 3rd vertical spindle, left POWERLOCK/HSK ----- Shared motor with 1st right spindle PowerLock tool holder Shared speed with right vertical spindle Tool cutting radius for longitudinal machining 93-232 mm Maximum throat depth 45 mm Minimum throat depth with tool cutting radius 200 mm: 20 mm Axially adjustable travel under table 30 mm Insertion segment 125 mm Insertion segment 150 mm 4th spindle, horizontal, top ----- Motor with brake: 5.5 kW Diameter 40 mm Speed ??6000 rpm Tool cutting radius 125-200 mm Maximum chamfering depth 30 mm Minimum chamfering depth with a tool cutting radius of 200 mm: 20 mm Axially adjustable range 30 mm Glazing bead removal after the upper spindle 5th spindle, second, horizontal, bottom ----- Motor with brake: 4 kW Diameter 40 mm Speed ??6000 rpm Tool cutting radius 125-200 mm Maximum chamfering depth 15 mm Axially adjustable range 10 mm Machine operation ----- Both axes of all spindles - with the exception of the first lower spindle - are equipped with mechanical digital displays. Central radial adjustment with mechanical digital display of the feed rate along with the pressure in front of the upper spindle. The pressure after the upper spindle can be adjusted separately. Memory function ----- For saving the setting values ??of profiles Tool holder axes and pressure elements before and after the upper tool holder with electronic dual displays: Function: -Saving the setting values ??of the finished profile at the touch of a button under a profile number - When the profile number is selected again, the electronic dual displays show the setting values - By manually adjusting the tool holders and pressure elements, the displays are aligned - 99 memory locations 3 axial CNC-controlled adjustment and positioning of the spindles in conjunction with the memory function. For spindles 2, 3, an...

Condition: used, Weinig Profimat 23 planer and moulder for four-sided planing and profiling of wood with tools and an additional glazing bead saw for window production. spindles: 5 Codpfoxc Hhwsx Ab Tehf spindle 1: Below spindle 2: Right spindle 3: Left spindle 4: Upstairs spindle 5: Below spindle 6: Glasleistensäge working width: 230 mm working height: 120 mm Total performance: 28 kW Rated current: 60 A

Condition: good (used), Year of construction: 2012, fuel type: electric, immediately operational condition, duplex lifting mast, without sideshift but control circuit available, 13795 hours. May change with use The battery from 2014 was regenerated by a specialist company in 2023, and some cells were also replaced 80 V, lifting height 3300 mm. Fork length 1600 mm Forward-backward control via foot pedal as with Linde Codoiqpp Sepfx Ab Tshf