Compressor

COMPAIR D315RS

Condition: like new (used), Donau Donauflex 135 High-Speed Radial Drilling Machine Manufacturer: Donau Model: Donauflex 135 Year of manufacture: 2020 Condition: Very good, used but like new Gbodpexcyz Rsfx Af Usi Available immediately from stock.

Condition: new, functionality: fully functional, machine/vehicle number: 8153336470, overall weight: 616 kg, volume flow: 399 m³/h, pressure (min.): 4 bar, pressure (max.): 13 bar, noise level: 67 dB, type of cooling: air, Equipment: documentation/manual, refrigerant dryer, type plate available, We are a company specializing in the compressed air industry for over 20 years. Professional level of service and high quality goods offered by our company - "proven" on the market - guarantee successful cooperation with you. We offer NEW screw compressor Atlas Copco GA37VSDs FF (variable speed with built-in dryer) Machine equipped with frequency converter (inverter), manufactured based on the latest technologies, which translates into greater efficiency and performance: On average 20% lower unit energy consumption (SER) than in previous models of the GA VSD series. Ecological and efficient VSD+ variable speed drive system reduces energy consumption by an average of 50% compared to models that operate at idle speed. Regardless of energy savings, efficiency (FAD) increases by up to 12%. Efficient fan motor (compliant with the ERP 2015 directive) reduces energy consumption and noise level. Superior Motor Efficiency (iPM) up to 94.5% exceeding IE3 efficiency levels. Built to work hard for your success. The industry-leading GA Series oil-injected rotary screw compressor delivers unmatched efficiency, high productivity and low cost of ownership – even in the harshest conditions. Technical data: Gbsdpfowlp Hdsx Af Usi capacity at 4 bar: 15.69- 13.75 l/s / 0.94-7.85 m3/min capacity at 7 bar: 15.67-129.35 l/s / 0.94-7.76 m3/min capacity at 10 bar: 15.68-110.79 l/s / 0.94-6.65 m3/min Max pressure 10 bar (13 Bar variant on request) Voltage 400 V Motor 37 kW Noise 67 dB(A) Weight 616 kg Motor with internal permanent magnets (IPM) Compression element Direct drive Innovative fan Separator/oil filter with durable construction Electronic water drain valve that does not cause compressed air losses Controller Elektronikon Inlet valve VSDs module Manufacturer code: 8153336470 If you are not sure whether the device is right for you, you have not found the right compressor, CALL! We will advise you on the right choice of device. We invite you to familiarize yourself with our full offer.

Condition: good (used), Year of construction: 2014, Has been serviced regularly. Gjdpfjvmpt Ujx Af Ujbi Technical values: 81.2 L/s, 13 bar. Connection values: 400V / 50HZ, 26kW Width: 1260 mm Depth: 860 mm Height: 1500 mm Weight: 520 kg

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, Erlo SEAR 25-RS drill, gear drill with automatic feeds, includes threading system, spindle speeds 64-3060 rpm, with chuck and protection, machine in very good condition, year 2006 Godpfxev Rnhxs Af Usbi

Condition: good (used), Year of construction: 1984, machine/vehicle number: 332, Offer 24130 Technical data: - Drilling capacity into solid steel ST 60 32 mm - Drilling capacity GG 25 40 mm - Thread cutting ST 60 M 27 - Drill spindle holder MK 4 - Quill stroke 150 mm - 12 drill spindle speeds 102 - 2000 rpm - 3 drilling feeds 0.1 - 0.3 mm - min. / max. distance spindle - table 310 / 610 mm - Drilling radius min / max 380 / 1200 mm - Table height 720 mm - Table size 1200 x 500 mm - Drive 400 V / 2.0 / 2.4 kW - Space requirement approx. W 1200 x H 2800 x D 2300 mm - Weight approx. 1500 kg - with: - thread cutting device - hydr. columns + boom clamping - Coolant device Gedpfx Aetxzrwof Uobi - Vertical T-slots on the rear side of the machine

Year of construction: 2022, operating hours: 975 h, condition: used, functionality: fully functional, overall weight: 9,600 kg, total length: 6,050 mm, total width: 2,450 mm, total height: 2,700 mm, machine/vehicle number: B0501, The MAGNETIC DRUM consists of a two-stage drum magnetic separation system designed to remove all magnetic particles from a material stream. Because the intensity of both magnetic drums can be selected and each drum can be activated or deactivated as needed, this module is highly flexible and can always be adapted to the specific properties of the feed material. The dual magnetic separation enables higher purity levels while maintaining constant throughput. This module is part of our rental fleet. Gsdpfx Afext Dqqj Uebi

Year of construction: 2015, condition: ready for operation (used), An oil-free, water-injected Atlas Copco screw compressor is available. Volume flow: 1.3m³-5m³/min, max. pressure: 13bar, motor power: 30kW, machine dimensions X/Y/Z: approx. 2000mm/1000mm/1500mm, weight: approx. 1300kg, operating hours: 46000h. Documentation available. On-site inspection is possible. Gbodpfx Asudy Sdjf Uoi

Condition: used, functionality: fully functional, Year of construction: 2013, operating hours: 69,301 h, control type: CNC control, degree of automation: automatic, laser type: CO₂ laser, laser source manufacturer: Trumpf, laser source model: Truflow3200, laser hours: 41,349 h, laser power: 3,200 W, sheet thickness (max.): 20 mm, sheet thickness steel (max.): 20 mm, sheet thickness stainless steel (max.): 12 mm, sheet thickness aluminum (max.): 8 mm, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 115 mm, feed rate X-axis: 140 m/min, feed rate Y-axis: 140 m/min, repeat accuracy: 0.01 mm, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, Equipment: nozzle changer, Trumpf TruLaser 3030 (L20) Laser Cutting Machine Year of manufacture: 2013 Working area: 3000 × 1500 × 115 mm Rated laser power: 3,200 W Control system: Siemens Sinumerik 840 D SL Maximum sheet thickness: Steel (St): up to 20 mm Stainless steel (VA): up to 12 mm Gbedpfxoxmpn Us Af Uei Aluminum (Al): up to 8 mm Maximum traverse speed: 140 m/min Positioning accuracy: 0.01 mm Dimensions: Length: 9,300 mm Width: 4,600 mm Height: 2,200 mm Weight: 12,000 kg Equipment: Automatic nozzle changer, voltage stabilizers included

Condition: excellent (used), Year of construction: 2013, ATLAS COPCO GA30+ screw compressor, machine after service Technical specifications: Capacity: 4.94 m³/min; 30 kW motor; Maximum pressure: 10 bar; Year: 2013 Hours: 10,814h!!! Price: 19,500 net 23,985 gross The compressor is fully operational, ready for work, with warranty. Godpsw Nh H Asfx Af Uebi We provide service. Below is a link to a video.