Arth-Pax Kft

Condition: used, Year of construction: 1994, operating hours: 392 h, functionality: limited functionality, machine/vehicle number: 1115, type of input current: three-phase, total height: 150 mm, total length: 2,200 mm, total width: 900 mm, overall weight: 1,800 kg, power: 11 kW (14.96 HP), input voltage: 380 V, Equipment: documentation/manual, Brand: Pawert Type: I-40/85 Year of construction: 1994 Capacity: 150 kg/hour Briquette dimensions: Ø 40 mm Motor: 11 kW Blsdpfxjzyau Eo Acnol Weight: 1800 Including feed screw and discharge chute.

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Bodpozvq Rcofx Acnell Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price: 35 000 EUR (VAT is not included)

Condition: used, Münch RMP 660 pellet press for the production of wood pellets and biomass pellets from sawdust, wood shavings and other organic waste materials. The machine is suitable for industrial pellet production, offering high pressing capacity and consistent pellet quality. Ideal for wood processors, sawmills and biomass plants. Technical data: - Screen: 6 mm - Motor: 2 x 90 kW Bodpfx Acjzryyrenell - Inner diameter of die: approx. 660 mm - Number of press rollers: 2 - Pressing capacity: up to approx. 3–5 t/h

Condition: used, Year of construction: 2003, power: 250 kW (339.91 HP), CPM 7930-4 Pellet Mill High-capacity pellet production machine manufactured by CPM. Designed for processing wood, biomass, animal feed and other pelletizable materials into pellets. The machine has been used for only one season and is in very good technical condition. Equipped with: Electric motor: 250 kW Mixer Feed screw conveyor Complete set of rollers Die Manufacturer: CPM Model: 7930-4 Bledpfxszlgxbo Acnjl Year of manufacture: 2003 A key machine for a complete pellet production line – ready for installation and operation.

Condition: new, Year of construction: 2023, We offer this new pellet press with a packaging line, manufactured in 2023. Manufacturer: Artmash (Ukraine) Year of manufacture: 2023 Production capacity: 700-900 kg/hour Die: 6 mm Condition: new (10 tons produced for testing) Category ID: 917 Type ID: 2701 Type: pellet press with packaging line Bsdpfx Acezh Hd Nensll If you have any questions or require additional information, please send us a message or call us.

Condition: like new (used), Year of construction: 2024, Pellet production plant – complete line – fully automated Salmatec press Rematec hammer mill Belt dryer Bledszg Eudjpfx Acnsl VAI bagging machine Cooler Sifter Palletizer Less than 1000 operating hours – certified Option for on-site reinstallation Option for on-site operator training

Condition: ready for operation (used), functionality: fully functional, suction capacity: 20,000 m³/h, production capacity: 1,300 unit/h, No minimum price – guaranteed sale to the highest bidder! The hammer mill (year of manufacture 2021) has only approximately 2 operating hours! The system is suitable for straw, hay, alfalfa, compost, wood, and other agricultural raw materials! TECHNICAL DETAILS Capacity (material-dependent) max.: 1,300 kg/h MACHINE DETAILS Hammer mill power: 75 kW Pellet press: 75 kW, without control unit Bale shredder: 35 kW, including control unit Bledpszgf A Uefx Acnel Dust filter capacity: 20,000 m³/h, including control unit Operating hours Entire line: approx. 1,500 h Hammer mill: approx. 2 h EQUIPMENT Pellet press Conveyor belt Elevator Pellet cooler with screen Buffer tank with discharge 2 cyclones with rotary valve airlock Fan for cooler extraction New die Various used spare parts 10 m feed table for the bale shredder Bale shredder, including control unit Hammer mill, including control unit Centrifugal separator Big bag station for dust filter Dust separation technology: EU-ATEX Directive 2014/34 Positive dust explosion assessment from 2023 Note: The line has already been dismantled and is ready for loading.

Condition: used, functionality: fully functional, For sale is a Gránit-Mill 90 pellet press in good condition, suitable for pellet production or use in the animal feed industry. The main components of the machine are: * Pre-hopper * Feeder screw * Permanent magnet * Conditioner * Press * Control cabinet Motors: * Pre-hopper motor: 1.1 kW * Feeder motor: 1.5 kW * Conditioner motor: 15 kW * Table motor: 0.55 kW Bedpjzc Eudofx Acnell * Main motor: 90 kW Accessories: * 2 stickers * 1 set of grooved rollers (total of 2) Additional information: The control cabinet was originally designed for the simultaneous operation of two presses, but it is also possible to control the presses separately. Price: * 1 Gránit-Mill 90 press with complete accessories and control cabinet: 29,000 EUR * When purchasing two presses together: 44,900 EUR The machines can be viewed at our location by prior arrangement. Further technical information, photos, and videos are available upon request.

Condition: refurbished (used), functionality: fully functional, machine/vehicle number: 9825, The 2024 general overhaul includes, among other things, the die head, hydraulic nut, bearings, main shaft, oil pump with filter, and synthetic oil. Only the steel housing is older but is in excellent condition. The images of the production line in the hall date from before the overhaul. The individual images of the Amandus Kahl pellet press show the condition after the overhaul. TECHNICAL DETAILS Motor power: 110 kW Sawdust capacity: 2.5 – 3 t/h Biomass capacity: 3 t/h Bran capacity: 3.5 – 4 t/h Straw capacity: 2 – 2.5 t/h L/D ratio: 3.67:1 MACHINE DETAILS Dimensions of press (W x H): 1,450 x 1,900 mm Bedpfx Acjzaricjnoll Diameter of press: 2750 mm Insertion depth: 6 mm Press length: 22 mm Year of manufacture of motor: 2024 Year of manufacture of cooler with sieve: 2015 Year of manufacture of conveyor belt: 2015 Year of manufacture of feed screw: 2015 EQUIPMENT Amandus Kahl C35-780 pellet press with base plate New 110 kW electric motor Electric control cabinet with emergency stop Complete electrical documentation Conveyor belt Sieve system with automatic cooling Hydraulic nut Die head Electrical wiring Metering screw for product feed Automatic metering system for filling 4 additional dies, 6 mm 60 liters of additional synthetic oil 7 new bearings 2 new wear rings 1 new air filter 2 new oil seals 1 new oil filter 1 new oil pump 20 liters of 800/460 synthetic oil 1 new thrust piece (main shaft) Documentation of overhauled and renewed parts

Condition: used, Pellet press Bledpfx Aey E Rrbjcnel Manufacturer: CPM Model: 7930-4 Year: 2019 Complete with feed mixers

Condition: reconditioned (used), Year of construction: 2022, functionality: fully functional, machine/vehicle number: 305.1103.08, type of input current: three-phase, Ipari pellet prés – CLM 630.G.LG típus (200 kW) Eladásra kínálunk egy CLM 630.G.LG típusú ipari pellet prést, amely korábban üzemszerűen működött pelletgyártó üzemben. A berendezés robusztus, nagy teljesítményű, folyamatos ipari termelésre tervezve. A gép üzemi körülmények között tesztelt, dokumentált előélettel rendelkezik, és kiváló alap lehet pelletgyártás újraindításához vagy bővítéséhez. Gyártási kapacitása 2,5-3 tonna/ óra fapelletből. A gép 2008-as gyártású, teljeskörű felújítására 2022-ben került sor. La Meccanica vertikális hűtő (4,5 kW) La Meccanica kalapácsos daráló (132 kW) Előtartály (kb 5 tonna pellet) Siló szárazfűrészpor (60 m3) Bjdpey Ddl Esfx Acnsll Továbbá a szállítószalagok, szállítópályák a hozzátartozó garatok, vezérlés. Kiegészítő alkatrészek, tartalék matricák (4 db), automata zsírzás.

Condition: like new (used), Year of construction: 2023, operating hours: 200 h, functionality: fully functional, Complete pellet production line, consisting of: Wood chip feed hopper 8m³ Hammer mill 22 kW Chip bunker with 3 discharge openings Blsdsy Ayiwspfx Acnjl Screw conveyor with dosing unit (binder) Walw pellet press Conveyor belt Pellet cooling bunker with packaging unit and fine particle screening

Condition: used, Complete pellet production line with a maximum capacity of up to 5 tons per hour (limited by dryer capacity). Pellet Presses (3 units): CPM 7122 CPM 7922-2 CPM 7930-4 (only ~200 working hours) Hammer Mills (3 units): Maier hammer mill for wet material Maier hammer mill for dry material Kamas hammer mill (for burner material production) Cooling System: CPM pellet cooler Additional Information: Electrical and control systems are fully integrated into container units Production line has been in operation for approximately 2 years Belt conveyor, reception hopper 4 kW Dryer: distributor reception hopper 2,2 kW Conveyor belt, reception hopper 2,2 kW Worm conveyor for drum dryer 2,2 kW Drum dryer 7,5 kW Main cyclone 90 kW Sluice head cyclone 7,5 kW Fan cyclone 18,5 kW 1 Sluice cyclone 1 2,2 kW Sluice cyclone 2 0,55 kW Sluice cyclone 3 0,55 kW Worm conveyor for cyclones 1-3 3 kW Hammer mill – Maier 160 kW Hammar mill for dust burner – Kamas 110 kW Hammar mill for woodchips – Maier 132 kW Worm screw for elevator 4 kW Elevator for buffer pocket 7,5 kW Buffer pocket high/low 8/4,5 kW Scraper conveyor for the presses 2,2 kW Worm screw for dust mill 2,2 kW Press 1 CPM: Model: 7122 Main engine 160 kW Cascade mixer 7,5 kW Feeding screw 2,2 kW Oil lubrication 1,5 kW Grease lubrication 0,18 kW Press 2 CPM: Model: 7922-2 Main engine 250 kW 200 kW Cascade mixer 7,5 kW Feeding screw, frequency converted 2,2 kW Oil lubrication 1,5 kW Feeding screw 4 kW Press 3 CPM: Model: 7930-4 Work only 200 hours Main engine 250 kW Cascade mixer 7,5 kW Feeding screw 2,2 kW Oil lubrication 1,5 kW Oil cooler 2,2 kW Grease lubrication 0,18 kW Conveyor for warm pellets 2,2 kW Belt conveyor to the refrigerator 2,2 kW Pellet refrigerator, outflow 1,5 kW Fan for the pellet refrigerator 11 kW Fan for the suction 5,5 kW Elevator 2,2 kW Belt conveyor 1,5 kW Belt conveyor 4 kW Combustion air fan 45 kW Conveyor fan 22 kW Conveyor fan 11 kW Silo filter 0,04 kW Filter fan 4 kW Screw for dust silo 2,2 kW Blsdeyvz Afspfx Acnjl Driving motor for dust silo 1,1 kW Oil pump 1,5 kW Dosing screw 0,75 kW Sluice feeder 0,37 kW

Condition: new, Year of construction: 2026, Bio Machines has been designing production lines, manufacturing machinery, and providing assembly services for over 20 years. We offer both complete production lines and individual machines, tailored to your needs. Our solutions include: Pellet production lines Briquette production lines Drying systems: rotary and belt-type Hammer mills Moving floors Feed bins Wood chippers Chain, bucket, screw, and belt conveyors Cyclones Silos Pellet coolers Sawdust and pellet sifters Bagging machines for small bags and big bags Palletizing lines for bags And many other specialized machines Blsdpfxeylm Tyj Acnel

Condition: used, functionality: fully functional, Performance for 6 mm diameter pellets 2.5-3 t/h Blsdpfxsx S Ibgo Acnol We used it for about 5 years. It was purchased used but in very good condition. All bearings were replaced 1 year ago. It was working very well before it was disassembled. A new die with rollers has been manufactured for it and is available for an additional price. For additional information, please write on Whatsapp.

Condition: new, functionality: fully functional, Equipment: documentation/manual, | price list | prices | prices | prices | prices | prices | prices | prices | > > > > > ecomas.pl/price-list < < < < < You can view the prices at the very bottom of the listing: Documents / 20215835-01.pdf We offer a high-quality, low-speed pellet granulator. The pellet mill is 100% manufactured in our plant at ECOMAS Polska Czernikowo. We guarantee equipment designed to operate continuously in a 24/7 system. Our machines produce pellets that meet EU standards – properly compacted, free of harmful additives, with a calorific value of at least 4.6 kWh/kg. The main advantage lies in modern, hardened dies and rollers (60HRC+), manufactured with CNC technology. Our dies ensure high efficiency, low power consumption, and long service life of both dies and rollers. Another benefit is the lubrication of the main shaft with oil and oversized bearings, which significantly slows down wear! Are you struggling with your current granulator – bearing failures, low efficiency, clogged die, high power consumption, rapid wear of parts, etc.? With our machines, these problems disappear. We approach each customer individually! See how our machines produce, type in YouTube: ecomas_polskie_peleciarki Available power options: 7.5kW, 11kW, 15kW, 18.5kW, 22kW, 30kW, 37kW, 45kW up to 55kW. Composition: - complete head with 2/3/4/5 rollers on cylindrical bearings - welded body – fully filled with Orlen Oil Transol VG 320 - cylindrical-bevel gearbox (efficiency 98%) - base frame Blsdoxk Ta Nspfx Acnjl - bolted dies fi 230, fi 260, fi 285, fi 310, fi 400, fi 520; hole diameters 3, 4, 5, 6, 8, 10mm (100% stability, easy disassembly, and temperature control) - standard oil tank or optional tank with pump and oil installation (oil lubrication, easy oil replacement) - user manual - 12-month warranty The buyer receives a detailed operating manual and a one-year warranty. We provide full warranty and post-warranty service.

Condition: used, Granulation and packaging line. Model: HM700E PRO 11KW Year of manufacture: 2022 It includes: Hammer mill - shredder Chip mixer Chip feeder Granulator Vibrating table Product feed belt (conveyor belt) Pellet hopper with packaging equipment Bag sealer and chip moisture meter Hammer mill with cyclone Motor: 11 kW / 400 V Productivity: 300 - 700 kg / h Weight: 360 kg Soft start installed Cutting system 16 hammers Chip mixer: Volume: 1.0 m³ Chip feeder: Motor: 3.3 kW / 380V Feeds up to 800kg / h Granulator: Motor: 22 kW / 380V/50hz; Productivity: 300 - 700 kg/h Weight: 590kg Soft start installed Vibrating table: Weight 90kg Product feed belt (conveyor belt): Dimensions: 5m × 0.4m. Automated packaging equipment: Dimensions: 1, 90x2, 50x2, 30 Volume: 1.5m³ Blsdpexcy D Eefx Acnel Packing in bags: 1 - 50kg Equipped with two types of scales Bag sealer 220V Moisture meter

Condition: ready for operation (used), Year of construction: 2024, operating hours: 21 h, functionality: fully functional, total height: 60,000 mm, input current: 250 A, compressed air connection: 6.2 bar, input voltage: 380 V, warranty duration: 24 months, Equipment: documentation/manual, 1. Material feeding table with moving chain mechanism. Adjustable height min 0.8, max 1.4 and electric drive. 3kw L 4m 2. Large roller shredder with double blades, diameter 1.8m, depth 1.9m 380V 30kw 3. Connection point with a lock for feeding bulk materials to the crushing mill. 4. Hammer mill turbine 380v 35kw 5. Mixer for crushed raw materials, with adjustable feed hatch. Volume 4.8m3 380V 2.2kw 6. Large horizontal granulator with automatic lubrication system and programmable rotor automatic lubrication. Additional cooling of the granulator rings and fine dust extraction. MAX capacity 3T/H 380 90kw 7. Small moving conveyor belt Width 38cm, Length 2m 380v 0.5kw 8. Large transport belt with head valve Width 38cm Length 6m 380v 1.5kw Bodpfjw U Ugmjx Acnoll 9. Pellet cooler with cyclone for fine dust collection and head valve MAX capacity 3.5T/H 380V 3kw 10. Screener/vibrating table with screenings collector and screw feeder. 380V 1.5KW 11. Long screener cylinder with screening mesh Length 3m 380V 1,5kw 12. Conveyor belt with feed to packaging. Length 4.2m 380V 0.75kw 13. BIG BAG packaging unit with calibrated scales, tolerance +/- 5gr per 1T 14. Screw conveyor for feeding material to the automatic packaging machine in bags. Length 5m diameter 27.5cm 380V 3kw 15 Automatic packaging machine with bag sewing and PVC bag sealing. There is also an automatic labeling conveyor table. Max capacity 4.2T/H with air compressor. 16. New semi Electric 3T pallet trolley

Condition: used, Year of construction: 1985, functionality: fully functional, For sale: granulator from the renowned manufacturer Buhler. Bledjw Uh Nzspfx Acnjl Granulator model: DPAA-660 Motor power: 160 kW – option to install a more powerful motor – 200 kW. Die diameter: 660 mm, Die working width: 160 mm, Granulator output on straw / sawdust: 2 – 2.5 t/h The granulator is currently dismantled. For a committed buyer, we will assemble it using new wear parts. Contact for more photos and details. Machine available for inspection in Sępólnie Krajeńskie, Kuyavian-Pomeranian Voivodeship, Poland.

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, power: 75 kW (101.97 HP), For sale: fully operational pellet production line. Bledpfjw Ry U Iox Acnsl

Condition: used, Pellet presses Manufacturer: Bühler Model: RPWPR 900.138 EX 4 presses - Bühler 3-4 tons per hour 4 mixers 4 feed screw conveyors Bedpfsw Iy T Sox Acnjll 20 m long stainless steel chain conveyor 16 m long output conveyor Soft starters

Condition: used, Ražotājs: Munch Modelis: 420 Ražîba: 1 tonna stundā Elektrojauda: 2x75 kW Diametrs 420 mm Komplektā ar dzesētāju pēc kapitālā remonta clear 134 / 5,000 Translation results Translation result Manufacturer: Munch Model: 420 Production: 1 ton per hour Bledpowfqn Asfx Acnjl Electric power: 2x75 kW Diameter 420 mm Complete with cooler after overhaul

Condition: used, Year of construction: 1988, height adjustment type: hydraulic, 1x Used KAHL C39 - 1000 Pellet Press Pelletmill Incl. Hydraulic nut Incl. 4 Roller head Incl. 5 Roller head Incl. various spare parts Bedev N Rdaspfx Acnjll Incl. chassis 110kW 1500rpm Electric motor

Condition: good (used), Year of construction: 2007, functionality: fully functional, Pellet production line based on Italian producer Zepi pellet press, hammer mill, pellet cooler and sifter. Machines are really powerful and reliable. Some parts like hammer mill are completely refurbished. Year of production 2007. Blodpsvx S Ryofx Acnsl

Condition: reconditioned (used), Year of construction: 2008, functionality: fully functional, Fully refurbished pellet press from Italian manufacturer ZEPI. The main engine power is 315kW, which allows the production of up to 6t/h of wood pellets. The delivery set also includes a ZEPI ZC500 paddle mixer and a ZEPI ZFS250 feed unit. Bledpfx Acsvpvp Ionol