Zig Zag Separator

Zlomiarze Recycling Technology

Condition: good (used), Year of construction: 2008, Lindner Power Komet 2800 from 2008, used for the production of RDF. The machine is fully functional, has been regularly serviced, requires regeneration of the rotor and pressure Technical specifications: Model: Lindner Power Komet 2800 Year of production: 2008 Laodpfxsvt Uc Ue Agroi Application: Production of applied fuel (RDF) capacity: 7-9 tons per hour with a 40 mm sieve Technical condition: good, works, dismantled until the end in January 2025 serviced on an ongoing basis

Condition: used, Year of construction: 2018, pressure 800 t stroke 80 – 360 / 400 mm no. of strokes 3 – 60 /min distance between columns 4200 mm dayligth (stroke and adjustment up) 1400 mm column travel -side 1800 mm table surface area 4000 x 1800 mm Laodpfjw D Hkdex Agrei hole in the table 3400 x 450 mm table height over floor 950 mm ram surface 4000 x 1700 mm ram adjustment 305 mm material width 800 mm material thickness 0,7 - 6,0 mm material cross-cut 2800 mm² power requirement 475,0 kW Weight 154,00 t dimensions of the machine ca. 6,05 x 3,95 x 7,7 mxmxm total height over floor 6,6 m Servo-Press (Press, Coil Line, Transfer) - Press Schuler, MSD 2-800-4.0x1.8-400 Servo - eccentric drive in transverse-shaft design via 2 torque motors, hydraulic overload protection, motorised ram adjustment, ram counterbalance, main control panel with TFT touch colour display motor-driven retractable change plate, hydraulic slide-in clamping elements - Coil Line Schuler-Automation AC-UEL-M-0800 / AC-SH-9-70/160-0800 R-L / AC-RM-EHP-0800 Transfer Schuler-Automation AT2-M-800-500-405

Condition: new, Bunker conveyor suitable for the feeding of presses, shredding, etc.. Delivery throughout Europe possible. Technical data: POS. 1 feed hopper POS. Task 2, vol. 1, 5kW, conveyor width: 1100 mm, axis dimensions: 3500 mm POS. Platform 3, volume 1, 1kW, conveyor width: 1100 mm, axle size: 4700 mm Standard discharge height: 2800 mm (greater than possible with distance feet as shown on the illustration) Ordering goods Further information and data upon request Lodpedxwlqofx Agrjai

Condition: like new (used), Year of construction: 2024, Permanent overbelt magnetic separator TYPE DMPM1200 1.800 x 900 x 220mm ===== Solid steel construction, welded Construction welded & painted RAL 7016 (anthracite gray) Magnetabmessungen: 1.200x500x180mm Drive roller + deflection roller S235 steel welded and machined Ø220x700mm crowned, shaft fixed with tension bearings. Drive: GEMOTEG shaft-mounted geared motor 1.1KW, speed 0.4-0.6m/sec Connection 400V, 50Hz Protection class IP54 Drive ready for connection up to motor terminal box Laedpjtxn Irsfx Agroi (Commissioning must be carried out by a qualified electrician) PU conveyor belt DM 20/2 0+010 PU black matt 5.4mm thick Conveyor belt width: 650mm 9 pcs. TG-40 cleats high-frequency welded Belt material: 3-ply especially transversely stable * equipped with stainless alligator connectors RS125 Magnetic properties: Built-in magnetic core: Strontium ferrite Y30 Bonded SfRe strontium hard ferrite magnetic core encased in soft iron, so that a very high permeability can be guaranteed. Housing with 1.4301 stainless steel plate and pole pieces tightly closed and sealed.

Condition: good (used), Year of construction: 1987, in 2008 was rebuilt Melting capacity: 1,300 kW Laedpslu Dvdofx Agroi Input power: 1,600kVA Capacity: 1 X 2,000kg Control: Siemens S7 Weight: approx. 20 tons

Condition: new, Year of construction: 2024, Shreddershafts Type Hammel 850 ; Olnova 85 --- 6pc 8/8 disc with bearings, ready for installation Optionally available for wood, waste or metal version with matching sidecombs Delivery Time: After response WERT GmbH is a metalworking company specializing in the development and production of twin-shaft shredding tools for renowned brands such as Hammel, Arjes, Linder, Eggersmann, Terex, and Keestrac. With an in-house design department and a highly skilled team, we provide customized, innovative solutions that meet the highest quality standards. Our goal is to continuously meet the individual needs of our clients through technological excellence and improvement. We serve companies across various sectors, including waste management, recycling, and mechanical engineering, and place great importance on long-term partnerships. With our reliable and high-performance shredding solutions, we help our clients increase their efficiency and competitiveness. Lsdpjhpipdsfx Agrjai

Year of construction: 2025, condition: new, The LITech hammer mills HM 120/200/300/400 are ideal for the pre-shredding of medium-hard, hard-tough & brittle materials such as floors, precious metals, electronic scrap, epoxy resin, gypsum, glass, catalysts, ceramics, clinker, coal, coke, minerals and much more many more!! Laedpfx Agog Ay Dhsrsi

Year of construction: 2004, condition: used, Max. operating temperature: 1270°C, roller dimensions: 45x35x2350mm, roller distance: 60mm, min. format: 150x150mm, working width: 1200mm, length: 80.000mm, including documentation. Laedpfx Ash Dbrhegrji

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: Lasdjvwlqqspfx Agroi The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2024, condition: new, Overview - of the different variants *Not every position is required: Optional: -Bale shredder MHB from 24.990 € net -MHZ straw mill from € 7,980 net -Special hopper 970 € net -Cyclone from € 3,750 net -Sheet metal silo demonstrator with discharge (only sketched in the picture) *optional, if you want to load with the wheel loader Unit price net from € 14,750 - Demonstrator -Dedusting auger - length approx. 4 m 4 sieves are mounted on the underside, which are extracted. Unit price net from: 9.750 € Ledpfx Asff Sbisgroai - Extraction parts / hoses flat rate 945 € net - Complete control system Net unit price: € 2,750 -Demonstrator extraction unit MMJET 160 Demonstrator, with cleaning Connection 160, fan 2,2kw air capacity 1850m³ /400 V Automatic compressed air cleaning Unit price net from: 6.950 € -Baler B 400 Bales approx. 400x400x800 (height adjustable) Up to 30 bales per hour with + - 20 kg from 59.995 € net *A reference system (baler) is located in zip code: 64579 Gernsheim Technical data: Bale size (WxDxH): 400 x 400 x 800 (height can be adjusted on request) Bale weight +/- 20 KG (depending on material) Capacity: approx. 30 bales per hour Storage container approx. 0.7m³ capacity Filling level sensors for min./max. filling level in the container Hydraulic pre-compressor Hydraulic compression ram Hydraulic unit, valve block with oil tank Pump 18.5 KW / 50 liters Rollers in the bale chamber for easy bale push-off Dimensions (l x w x h) 3105x2830x2455 mm Weight approx. 1500 KG mütek baling presses / wrapping machines are designed for the production of bales from a wide variety of materials such as shredded micanthus or elephant grass, wood chips, sawdust and shredded straw. straw. The machine is characterized by a robust design that guarantees consistent quality in continuous operation. quality in continuous operation. The baler compacts the material filled into the storage container without the addition of binding agents and packs the material into plastic bags. The volume of the material can be considerably with the baling press. The volume reduction rate depends on the material. The maximum material moisture content must not exceed 18 % Atro. The container of the mütek baler can be fed automatically or manually and has a volume of approx. 0.7 m³. volume of approx. 0.7 m³. Containers with a larger volume or with an attached suction and filter system as a complete disposal unit are also available. In addition to automatic filling via deduster, mütek also offers filling by means of screw conveyors. With both variants, automatic automatic dedusting is possible. mütek baling presses are equipped with a control cabinet for the control system. In the standard version, the dimensions of the bales (width x depth x height) are 400 x 400 x 800 mm. However, the height can be adapted to your requirements on request. The following advantages arise in the production of bales: - simple and safe storage - No loose dust - Minimization of the storage volume - Low transport volume *Requirements for source material: - dry (max. 30 % ATRO) - Maximum length 35 mm