Wartsila 220SG

wartsila 220sg

Condition: ready for operation (used), Year of construction: 2018, operating hours: 60,000 h, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, input frequency: 50 Hz, power: 3,028 kW (4,116.93 HP), empty load weight: 10,000 kg, fuel: domestic gas H, control cabinet height: 2,000 mm, control cabinet length: 600 mm, control cabinet width: 800 mm, nominal power: 2,679 kW (3,642.42 HP), rotational speed (min.): 1,500 rpm, type of cooling: water, GE Jenbacher JMS 616 GS-N.L Gas CHP Unit Fuel Type: Natural Gas Electrical Output: 3,065 kW Thermal Output: 2,420 kW Total Efficiency: 85.6% Electrical Efficiency: 42.9% Thermal Efficiency: 42.7% Voltage: 690 V Frequency: 50 Hz RPM: 1,500 Engine Configuration: V16 (60° angle) Bore x Stroke: 190 mm × 220 mm Displacement: 99.8 L Fuel Consumption: Approx. 597 Nm³/h (at LHV 9.5 kWh/Nm³) Noise Level: 101 dB(A) at 1 metre Blodpfxjwptfre Aafsc Dry Engine Weight: approx. 10,000 kg Dimensions (L×W×H): 8,300 × 2,200 × 2,800 mm ⚙️ Included Equipment Turbocharged engine with intercooler STAMFORD LVSI 804 W alternator (rated 3,555 kVA) LEANOX control system Electronic ignition system Full lubrication system (pump +filters) Heat exchangers for coolant and oil Control panel with visual interface Pre-heating system Gas train according to DIN-DVGW standards

Condition: used, Year of construction: 1994, Technical details: production capacity: 2x 4,8 MW number of Generators: 2 Stück fuel tank capacity: 480 m³ type of fuel: Gas + Öl Complete Power Plant 2 combustion engines 12 cyl V -Motor Make Maschinenwerke Halberstadt Type: 12 VDG for oil and gas 2 Generators Make Leo Somer with: - electrical capacity 4,6 MW each Bljdpfeu Nxatsx Aafsc - mechanical capacity 4,8 MW each - thermal capacity 4,8 MW each - 2 recovery boiler - Stromeinspeisung: Mittelspannung 10 KV (direkt ins Netz) furthermore: heat exchanger, catalyst, control room, medium high voltage system, oil preparation plant, intermediate storage tank + fuel depot tanks 4,8 m³ *

Year of construction: 2023, condition: new, * Year of construction 2023 (new unit); * Primary power (PRP) 32 kVA / 26 kW; * Nominal standby power (ESP) 33 kVA / 26 kW; Blodpfxsl Iyyuo Aafjc * Rated voltage 400V; * nominal frequency 50Hz; * with terminal strip (without sockets outside) * dimensions: 2.225 x 970 x 1.185 mm (LxWxH) - weight, without fuel: 137 kg

Year of construction: 1981, condition: used, pressure 40 t distance between columns 600 mm stroke 160 mm table-size 560 x 400 mm dayligth 360 mm ram hole 40 H 7 DIN 810 mm oil volume 500 l return speed 200 mm/sec die cushion hydr. pressure/stroke 60 capacity of ejector 25 t total power requirement 15 kW dimensions of the machine ca. 1.44 x 0.95 x 2.54 m Blsdpfx Aasb U Hw Tsfsc pressing speed 27 mm/sec return speed 200 mm/min

Condition: excellent (used), Year of construction: 2010, operating hours: 122,471 h, functionality: fully functional, power: 1,095 kW (1,488.78 HP), fuel: domestic gas L, rotational speed (min.): 1,500 rpm, type of input current: three-phase, Jenbacher J320 GS Gas Generator – 1095 kW Main specifications: Engine model: Jenbacher J320 GS Rated power: 1095 kW (ISO 3046) Speed: 1500 rpm Engine weight: 5200 kg Year of manufacture: 2010 Running hours & performance: Total operating hours: 122,471 h Active energy produced: 11,781 MWh Reactive energy: 7,327.8 Mvarh Bljdpfexb D Hbox Aafjc Alternator: Manufacturer: Stamford (AC Generators) Bearing types: 6319 C3 / 6228 C3 Grease type: Kluber Asonic GHY72 Re-lubrication interval: every 4000–4500 hours Heat exchanger: Manufacturer: Tranter International AB Model: GXD-042 Year of manufacture: 2010 Max. operating pressure: up to 30 bar Max. operating temperature: up to 75 °C Connection material: steel Condition: Equipped with Jenbacher DIA.NE control and monitoring system Fully serviced in line with OEM schedules by an official service centre Excellent working condition 📍 Location: England

Condition: excellent (used), Year of construction: 2005, power: 225 kW (305.91 HP), fuel type: diesel, type of cooling: water, Regularly maintained Volvo Diesel fire water pump for sale in new condition Machine hours: 298 inspection and oil change at all maintenance intervals, regardless of use. Bedpfx Aohfl Dmjafolc Manufacturer: Kagema DPA Engine: Volvo Penta TWD 710 V 218 kW / 296 HP 6-cylinder diesel engine Data: Manufacturer: Volvo Penta Type: TWD 710 V. Spec.NO .: 868725 Serial number: 2071093240 Vermogen: 225 kW / 304hp Speed: 2450 rpm Fuel: diesel Length: 330 cm Width: 120 cm Height: 220 cm tank: 400liter water transport ca: 800-900m3 6.5 bar pressure water pump type: KSR-MXN 150-315 "missing" Purchase of industrial equipment and machinery. Wide Range of Used Machinery, Industrial Equipment

Year of construction: 2010, condition: good (used), CNC BIESSE BREMA EKO 902 INSERTS FOR SALE TECHNICAL DETAILS: 3-AXIS C.N.C. MACHINING CENTRE (X-Y-Z) - Integral protection of the operating spindle and the working area on the machine. - Numerical control (control) with BIESSE Works software on Windows. - Vertical positioning of the panels, with N. 2 panel locking clamps. - Panel feed (in X-axis direction, on the lower support with rubber wheels), movement (in X-axis) of the panel/board clamps. DIMENSIONS OF THE PALLETS (WORKING DIMENSIONS): - Length Min mm 160 / Max mm 3200 - Width Min mm 35 / Max mm 900 - Wait Min mm 8 / Max mm 80 WORKING GROUPS: - No. 1 Spindle (electro-spindle) vertical ER32 (KW 4,5) with reversing (up to 18000 RPM). - No. 1 Circular saw (for grooves) diameter mm 120 (fixed X axis) - No. 13 Independent vertical spindles for drilling (6 in X-axis + 7 in Y-axis) - Nº 8 Independent horizontal spindles for drilling (3+3 on X axis and 1+1 on Y axis) Blodpehknbrjfx Aafec - Nº 1 Hinge drilling head unit - Total installed power 20 KW AUTOMATIC DOWEL INSERTION GROUP ON BOTH SIDES WITH PRESSURE PUMP TO APPLY THE GLUE.

Year of construction: 2009, condition: good (used), hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Pressure force: at 250 bar 96 to Bjdodq U S Ispfx Aafelc -Piston diameter: 220 mm -Piston rod: Ø 125 mm -Cylinder tube outside: Ø 260 mm -stroke: 495 mm -Total length retracted center hole: 1195 mm -Piston rod mount: Ø 100 mm -Cylinder mount: Ø 100 mm -universally applicable: -Number: 15x cylinders available -Price: per piece -Dimensions: 1360/530/H300 mm -Weight: 364 kg/piece

Condition: excellent (used), CNC Machining Centre for Routing, Drilling, and Edgebanding of Straight and Curved Panels 4-Axis Electrospindle – HSK F63 Automatic Tool Changer with 12 Positions Bledpfx Aajlpf E Usfjc Boring Unit Edgebanding Unit Edge Storage with 3 Positions Vacuum Pump

Year of construction: 2023, condition: new, machine/vehicle number: 28086221201 (AABM0013), MASTERWOOD CNC machining center type PROJECT TF 100 2.0 "PARTNERSHIP EDITION" - MAST0337 Technical data: Axes: X axis: Max. Workpiece length: unlimited Min. workpiece length: 250mm Traversing speed: 0-25 m/min. Y-axis: Max. Workpiece width: 1.000mm for all aggregates Min. workpiece width: 85mm Traverse speed: 0-50 m/min. Z-axis: Max. Workpiece thickness: 60mm Min. workpiece thickness: 10mm Traverse speed: 0-20 m/min. Aggregates: 16 drilling head: vertical spindles in X-direction: 5 pcs. vertical spindles in Y-direction: 5 pieces horizontal double drilling spindle in X-direction: 2+2 pieces horizontal double drilling spindle in Y-direction: 1+1 pieces distance drilling spindles: 32mm speed of drilling spindles: 4.000 rpm. motor: 1,7 kW grooving saw: in X-direction Speed of rotation: 4.000 rpm. Max. saw blade diameter: 125mm Motor: 1,7 kW (the grooving saw is integrated in the drill head) Control system: Personal computer Operating system: Windows 10 Pro - 64 bit Processor: Intel Hard disk with at least 300 GB of storage space CD-ROM drive Color monitor Video card integrated 2 Ethernet cards Program: MASTERWORK MACHINE VERSION Other data: Required air pressure: 8 bar Air consumption: max. 750 l/min Extraction: Volume: 2,000 m³/h Air speed: 25 - 30 m/sec. Suction nozzle: 1 x 150mm Other equipment features: - Air tables at the working area - Roller table at infeed and outfeed - Sensor for plate measurement - Ball screw and linear guides - Rack and pinion drive - Import of DXF files (operating instructions, switching and pneumatic diagrams are in digital form) "PARTNERSHIP EDITION" consisting of: Milling unit, incl. MASTERWORK software extension Speed: 1.000 to 18.000 rpm. Motor: 4,5 kW with ISO 30 intake Incl. integrated suction control (During drilling only the only the drill head is extracted, for milling only the milling unit is extracted) 6-fold tool changer 3 pieces ISO 30 collet chuck incl. collet chuck Tool equipment, consisting of: HW dowel drill: 5 pieces 5mm - GL 70mm - blind hole drill. 1 piece 5mm - GL 70mm - through hole drill bit 4 pieces 8mm - GL 57,5mm - blind hole drills 2 pieces 10mm - GL 57,5mm - blind hole drills 1 piece 10mm - GL 70mm - blind hole drill bit 1 piece 8mm - GL 70mm - blind hole drill bit 1 piece 15mm - GL 70mm - blind hole drill bit 1 piece 35mm - GL 70mm - blind hole drill bit 1 HW grooving saw blade d=125mm, bore=20mm, width: 4,0mm, Z=35 WSA 1 DIA cutter, right - GL=103mm, NL=43mm, D=18mm, shank: 20x50mm, Z 1+1 1 DIA cutter, left - GL=103mm, NL=43mm, D=18mm, shank: 20x50mm, Z 1+1 1 VHW-WP finishing cutter, right, D=10mm Foldable roller conveyor in the infeed Foldable roller conveyor in the outfeed Automatic central lubrication plus options: Complete package for CLAMEX connectors € 3.500,00, Blsdpfx Aasiukvkofoc complete door package € 3.500,00, software package PaletteCAD start + CAM connection € 3.000,00, freight, installation, instruction € 3.000,00, immediately available from location Seevetal, subject to prior sale.