Other

TEREX TA30 GEN7 6x6 Dumper ZSA

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered Hnsdjrgzv Nepfx Agmjn * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Year of construction: 2023, condition: new, Layout: Backhoe 20 years of experience, long boom-arm manufacturing suitable for all brands and models Hjdsn Tmy Rspfx Agmenn Please send a message or call for information and offers.

Condition: used, Year of construction: 2015, operating hours: 6,850 h, power: 129 kW (175.39 HP), front tire size: 600/70R28, rear tire size: 710/70R42, Equipment: compressed air brake, OPERATING HOURS 6800 / AUTOPOWR / IVT - 50 KM / COMMAND CENTER DISPLAY AUTOTRAC PREPARED / JDLINK-CAPABLE / 4600 PROCESSOR / CAB PR.-CV CAB WITH COMMAND ARM STANDARD SEAT / MIRROR - MANUAL TELESCOPIC PANORAMA WS W/PD / STANDARD RADIO / HYD Hjdpfx Aeu Rvklegmonn

Condition: excellent (used), power: 264 kW (358.94 HP), operation weight: 23,600 kg, tire size: Bridgestone 30/65R25, tire condition: 70 %, Year of construction: 2023, operating hours: 1,710 h, Equipment: air conditioning, VOLVO A30G Hnodpfx Agoya U Unomsn Year: 2023 Operation hours: 1.710 hrs. ROPS Airco Back drive camera Radio Central lubrication body heating Tailgate Bridgestone tyres 30/65R25 approx 70% good VOLVO D11M Motor with 264kW CE Transport dimensions L/B/H - 10.5 x 3 x 3.4m Operation weight: 23,6 to.

Condition: new, overall weight: 4,500 kg, Year of construction: 2026, LONG REACH excavator arm 8m, 10m, 12m, 14m, 16m, 18m, 20m. 22m + BOAT POSSIBILITY OF PRICING FOR ANY MACHINE. POSSIBILITY OF PRICING FOR LENGTHS FROM 8M UP TO 22M BELOW OFFER FOR Hedpfx Aeua U Acegmjnn LONG REACH BOOM 16M FOR JCB JS 220 + BUCKET 0.6 M3 TECHNICAL SPECIFICATIONS Material: S355 steel Length: 16 m Maximum reach: "forward": 15.5 m Maximum digging depth: 11.2 m Weight: ca. 4500 kg Dipperstick capacity: 0.6 m3 All pins are hardened (to increase hardness above 50 HRC) 1 bucket cylinder, 6 pipes, 4 hoses, 8 pins, 5 grease lines, 1 set of couplings Fabra: KAISAI brand (colour can be selected) Hose: GATES brand All pins are equipped with grease nipples All "pipes" are phosphated

Condition: new, empty load weight: 10,700 kg, maximum load weight: 38,800 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r 17,5, color: grey-black, Equipment: ABS, Gooseneck: •Gooseneck with bevelled corners at the front 45° and with a rear bevel of approx. 750 mm x 10° •3 pairs of lashing rings •Hardwood flooring 30 mm thick Loading area in extendable version: •Loading area in extendable version with rear bevel of approx. 1,000 mm x 8° •Cutouts in the outer frame of the loading area for hanging tensioning straps •Hardwood flooring approx. 48 mm thick, checkered sheet covering over the axles Two-part steel ramps: •One pair of galvanised, two-part steel ramps with approx. 48 mm thick hardwood flooring •Ramp with hydraulically foldable and unfoldable ramp parts, hydraulic lifting mechanism and hydraulically movable •Maximum load per pair: approx. 40,000 kg Axles and Tires: •BPW axles and suspension, 2 axles rigid, 1 axle with self-steering •Technical axle load: 12,000 kg •Electro-magnetic reversing lock can be activated via reverse gear and manually •Air suspension with lifting and lowering valve •Axle tool •235/75 R 17.5 3PMSF Brake system: •WABCO brake system in accordance with EU regulations with EBS-E Paintwork: •First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component zinc dust primer •A high-quality 2-component top coat in one color in MB 7350 Nova gray •Rear section metallized and painted in RAL 9010 Seatposts: •JOST seatposts with 2-speed gearbox for 24t lifting load (50t test load). Steel construction: •Steel construction made of high-strength fine-grain steel •Steel qualities: •S355J2+N/S355MC •S690QL/S700MC Electrical system: •Electrical system in accordance with EU regulations, 24 volt lighting •ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets Accessories included: •A spare wheel with holder •A galvanized steel bulkhead approx. 400 mm high •Yellow-red air couplings on the galvanized front connection panel Hnedpfx Aohlz S Negmjn •4 wheel chocks •A bracket for a rotating beacon at the rear of the trailer •Mounting in the rear area of the gooseneck for aluminum docking ramps •Galvanized folding supports under the bevel of the loading area •Cover plates to bridge the space between the ramps and the loading area •White Reflective tape in accordance with EU regulations on the side, on the extension and at the rear, red •Electro-hydraulic unit at the rear, under the loading area •A holder for the warning signs including a socket on the gooseneck and on the ramps on the left and right •Control valves for the ramps attached to the right-hand side of the trailer •ALU side walls and rear wall on the gooseneck, approx. 2,440 x 400 mm •The rear, galvanized plug-in stanchions are removable (length of the structure approx. 2,560 mm) •Four warning signs extendable by approx. 400 mm with a position light •3 pairs of WADER container pockets in the loading area for a 20ft, 30ft or 40ft container •6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading area •Galvanized extensions, extendable by approx. 230 mm each Page •Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area bevel •A painted layer of sand on the checker plates, above the kingpin and the loading area as anti-slip protection •Load pressure gauge for determining the axle loads including load diagram •HRM metallization (High Resistance Metallization) of the outer frame •Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, maximum load weight: 44,000 kg, overall weight: 61,000 kg, axle configuration: 3 axles, Year of construction: 2026, Further information here: Hnsdpfx Agjv D Abtsmen

Condition: used, functionality: fully functional, Year of construction: 2025, operating hours: 16 h, Powerful mini dumper in top condition for sale! The machine is in very good condition and ready for immediate use. Condition: Used, very good Operating hours: 16h Year of manufacture: 2025 SCHORR RR500DHKASH PRO tracked dumper – Discover the advantages: - 9.2 HP four-stroke engine - Self-propelled and powerful chain drive - Hydraulic bucket for self-loading - Hydraulic scissor lift (discharge height 1.44m) - 500kg payload - Large and high-quality tipping trough with a wide tipping angle - Foldable rider platform as standard - 6+2 gears The SCHORR RR500DHKASH tracked dumper features a hydraulic tipping drive and a payload of 500kg, as well as a powerful 9.2 HP single-cylinder 4-stroke gasoline engine. The RR500DHKASH's special features include its hydraulically controlled scissor lift function and self-loading bucket. This allows you to effortlessly load material and discharge it up to a height of 1.44 m – ideal for trailers, containers, or other elevated areas. Thanks to its slim design (825 mm), the mini dumper can also navigate narrow paths, making it an extremely flexible means of transport. The mini dumper's powerful track drive allows you to easily negotiate rough terrain, inclines, and curbs. The rubber tracks provide secure footing in any work area. Raising and lowering the tipping body/box is effortless and effortless thanks to the hydraulic tipping drive, even when fully loaded. With a robust body made of heavy-duty sheet metal and a straight discharge outlet that ensures quick and easy discharge, this dumper is a must-have for anyone who needs to transport heavy loads. Tipping on slight inclines is also no problem. The large tipping angle ensures that even fully loaded skips are completely emptied without manual assistance. This saves time and effort, making the motorized wheelbarrow an indispensable tool for anyone who values efficiency and performance. TECHNICAL DATA: Manufacturer (abbreviation): SCHORR Manufacturer's type designation: RR500 Model: DHKASH Load capacity: 500 kg Tilt drive: Hydraulic (stepless) Drive: Chain Weight without/with packaging: 439 / 464 kg Drive Engine: Air-cooled single-cylinder four-stroke engine (OHV) Starter: Recoil starter Power: 9.2 hp Transmission: 6 forward gears / 2 reverse gears Speed Forward gear: max. 8 km/h Reverse gear: max. 5 km/h Basic dimensions Total length of platform folded: 2320 mm Hodpfewh Nvkjx Agmonn Total length of platform unfolded: 2520 mm Total width (including bucket): 825 mm Total height retracted/extended: 1230 / 1620mm Total height at maximum bucket tilt (90°) retracted/extended: 1780 / 2400mm Container dimensions (internal dimensions): 740 x 665 x 435mm Container dimensions (external dimensions): 1060 x 710 x 520mm Bucket dimensions (internal dimensions): 650 x 320 x 300mm Track width: 710mm Loading volume (liquid): ~ 200L Loading volume (heaped): up to 370L (depending on load) Filling height Side: 1030mm Front: 810mm Discharge height min./max.: 810 / 1440mm We at SCHORR are happy to answer any questions you may have about our pallet trucks. You can reach our competent team by phone or email. We look forward to hearing from you and helping you with your consultation.

Condition: new, overall weight: 3,500 kg, Year of construction: 2026, LONG REACH excavator arm 14 m + bucket PRICING AVAILABLE FOR ANY MACHINE. PRICING POSSIBLE FOR LENGTHS FROM 8M UP TO 22M Hnsdjua Uy Uopfx Agmjn TECHNICAL SPECIFICATIONS Material: steel S355 Length: 14m Maximum reach: "forward": 13.5 m Maximum digging depth: 9.5 m Weight: ca. 3500 kg Dipperstick capacity: 0.9 m3 All pins are hardened (to increase hardness above 50 HRC) 1 cylinder bucket, 6 pipes, 4 hoses, 8 pins, 5 lubricating pipes, 1 connection kit Fabra: KAISAI brand (colour can be selected) Hose: GATES brand All pins are fitted with grease nipples All "tubes" are phosphate treated

Condition: new, Year of construction: 2023, construction height: 22,000 mm, Explore Galen Group's range of high-quality long reach boom-arms, designed to enhance operational efficiency and safety in challenging construction environments. The machine details on the photo Machine Model: Komatsu PC450 Hnsdpfxjq E Iw Rs Agmsn Total Length:22m Bucket Capacity: 1m^3 Usage Area: Port Construction For detailed information and inquiry, please contact us