Paal KES 1750 conveyor belt

Paal KES 1750

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Lodpfxsvf E Avj Apvjrl Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. Lrjdetvau Aepfx Apvol The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: ready for operation (used), DIXI 60SLD is a semi-automatic baling system with a pressing force of 60 tons, designed for economical volume reduction of recyclable residues in industrial and craft sectors: - Cardboard boxes Lodpfx Apora A E Usvorl - Foams - PET bottles - Insulation mats - and other pressable materials Horizontal baler, DIXI 60 SLD waste press with tipping device Technical specifications: Pressing force: 60 tons Specific pressure: 6.81 kg/cm² Power supply: 400V / 7.5kW Bale dimensions: 800 x 1100 x 1200 mm Number of ties: 3 Bale weight: approx. 370–410 kg Tying: manual Feed opening: 990 x 1110 mm Machine weight: 5,420 kg Average pressing cycle: 47 sec Year of manufacture: 2011–2016 Dixi 80SLD Baler Technical Data of the Baler Brand: Dixi Model: 80 SLD Pressing force: 80 tons Drive power: 11 kW, 400 V / 32 A Feed opening (W x H): 1040 x 1110 mm Pressing cycle: approx. 35 sec Throughput: approx. 1,000 kg/h Bale size (W x H x L): 1120 x 1120 x 1200 mm Bale weight: depending on material, approx. 500–600 kg Bale tying: triple, manual Machine dimensions: Length: 4,200 mm (+cage 1,600 mm) Width: 1,830 mm Height: 2,620 mm Machine weight: approx. 8,000 kg Automatic bale ejection Robust construction for long-term use Year of manufacture: 2016–2020 Weight: approx. 8.4 tons Condition: Used

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC80 (45kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. After refurbishment, this baler is sold with a 2-year warranty. Lodpfxotvat Ts Apverl

Condition: excellent (used), Year of construction: 2014, operating hours: 37,656 h, functionality: fully functional, pressing force: 85 t, filling opening width: 1,500 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 650 kg, overall weight: 25,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2024, volume flow: 410 m³/h, transport width: 2,400 mm, transport length: 9,300 mm, Hello, We are offering you a used baler from the manufacturer Presona AB, type LP 85 VH1, subject to availability. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot guarantee their accuracy or completeness. Manufacturer: Presona AB, Sweden Type: LP 85 VH1 Year of manufacture: 2014 Total operating hours: 37,565 hours, as of March 2025 Main press force: 85 t Specific press force: 100 N/cm² Pre-press flap force: 28 t Feed chute dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying system: 5-fold vertical Lrodov T I Evjpfx Apvsl Hydraulic oil tank volume: 1,000 L Press dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Press weight: approx. 25 t Note: The machine was used for compaction at a recycling plant. Used for the production of paper, cardboard, films, and plastics such as bottles, buckets, canisters, and drums. The press is in good condition. Many wear parts and entire assemblies have been replaced over the past three years. The machine has been regularly serviced. We would be pleased if this press is of interest to you. Your service team at Mertens & Frowein GmbH

Condition: defective spare-parts repository (used), Year of construction: 2013, Manufacturer: HSM Tip: HL 4010 Li Year of construction: 2013 Lsdeur Ravjpfx Apverl The equipment is incomplete and is sold as a part Fault: Hydraulic pump missing Control is missing Power supply unit missing

Year of construction: 2020, condition: excellent (used), cistern with conveyor in it with in front a dosing auger Ljdpsilqfqjfx Apvsrl length 9 meters width 2 meters

Condition: new, Roller splitter RGS20 Motor power 7.5kW Cutting force 20 tons Cutting channel designed for - max. roll length 1100mm Lrsdpoq A Turefx Apvol - max. roll diameter 900mm Machine weight approx. 2500kg Tank capacity approx. 100 liters -Body color RAL according to customer requirements Protective grille/blade bar RAL 1028 melon yellow Ordered goods Price and further information on request

Condition: new, Year of construction: 2026, functionality: fully functional, Waste Baler BTS-MF75 in stock and available straight away The BTS-MF75 is the ideal waste baler for compacting your loose cardboard and plastic film waste into a bale of up to 75 kg. With a can crush insert baler is even suitable for crushing individual sheet metal and plastic containers and also cans. The baling press impresses with its ease of use, safe operation and its large filling volume. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 3.5 Ton Bale weight: up to 75 kg (material depending) Bale size: 1000 H (var.) x 700 W x 500 D mm Machine size: 2335 H x 1040 W x 750 D mm Machine weight: 278 kg Transport height: 2335 / 1800 mm (on request) Loading aperture: 700 W x 698 H mm Cycle times: 24 seconds Motor: 1.5 kW 13 Amp Power supply: 220 - 240 V (1 phase) Noise level: 68 dB User-friendly lever control Bale trolley for removing the bales Retainer for reducing the material spring back Reel holder for 2 rolls of strapping A quality product “Made in Europe” Suitable for compacting Cardboard Plastic film and foils Cans and light sheet metal containers Canisters and light plastic containers Clothes Light valuable materials Optional extras Lredpsvah S Ajfx Apvsl Machine colour RAL Can crusher insert PLC auto compaction cycles with bale full light and E-stop with locking key Strap eject for easy removal of bales Strapping rolls Power supply 380 - 400 V (3 phase) Waste Baler, Waste Compactor, Cardboard Baler, Film Baler, Foil Baler, Packaging Plastic Film Foil, Bailer, Baling Press, Garbage Press, Trash Compactor, Baling Compactor, Paper Press, Waste Paper Press, Cardboard Press, Cardboard Compactor, Foil Press, Paper Baling Press, Waste Baler, Residual Waste Compactor

Condition: as good as new (ex-display), Year of construction: 2026, The BTS-MF500LH is the ideal waste baler for compacting your loose cardboard and plastic film waste into a bale of up to 500 kg. Due to the compact design and low height this baler is perfect for rooms with limited ceiling heights. The waste baler impresses with its ease of use, safe operation and its large filling volume. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 50 Ton Bale weight: up to 500 kg (material depending) Bale size: 1100 H (var.) x 1400 W x 800 D mm Lrjdpfxovugzfo Apvel Machine size: 2249 H x 2041 W x 1350 D mm Machine weight: 2100 kg Transport height: 2249 mm Loading aperture: 1400 W x 680 H mm Cycle times: 35 seconds Motor: 11 kW 32 Amp Power supply: 380 - 400 V (3 phase) Noise level: 68 dB Auto control panel with bale full light and E-stop with locking key Strap eject for easy removal of bales Retainer for reducing the material spring back Low height, perfect for limited ceiling heights Hour counter Reel holder for 6 rolls of strapping A quality product “Made in Europe” Suitable for compacting Cardboard Plastic film and foils Big Bags Cans and PET bottles Light valuable materials Optional extras Machine colour RAL Strapping rolls Waste Baler, Waste Compactor, Cardboard Baler, Film Baler, Foil Baler, Packaging Plastic Film Foil, Bailer, Baling Press, Garbage Press, Trash Compactor, Baling Compactor, Paper Press, Waste Paper Press, Cardboard Press, Cardboard Compactor, Foil Press, Paper Baling Press, Waste Baler, Residual Waste Compactor