Used Surface Sanding Machine for sale (65,675)

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Fpjdpot Tqy Ejfx Aa Eed Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: used, used, good condition, low operating hours Manufacturer: Johannsen Type: T82K Machine No.: 14883 GS-certified Motor: 7.7 kW Sanding length approx. 2700 mm Sanding width approx. 950 mm Belt length approx. 7800 mm Table size approx. 2800 x 950 mm Fpjdpfsythb Ujx Aa Eod Throat left approx. 850 mm Upper belt cover Adjustable upper sanding support Right-left run Belt blow-off Sanding shoe 450 x 140 mm Extraction connection D 160 mm Space requirement approx. 4300 x 1500 x 1400 mm Stock location: 97447 Gerolzhofen, free loaded, unpacked Handover in as-inspected condition, without warranty or guarantee

Condition: ready for operation (used), Year of construction: 1988, Horizontal surface grinding machine Okamoto Model PSG 63 – UAN Year of manufacture 1988 Grinding length 600 mm Grinding width 320 mm Maximum workpiece height 500 mm Table longitudinal travel 750 mm Table cross travel 340 mm Grinding wheel diameter 350 mm Grinding wheel width 40 mm Spindle speed 1,500 rpm Rapid vertical traverse 400 mm/min Power 3.7 kW Automatic feed Fodpfxsytayie Aa Eopd Magnetic chuck Coolant system Weight 2,500 kg Price: €2,500 plus VAT, ex-site

Condition: used, Year of construction: 1970, Technical details: grinding length: 1000 mm grinding width: 400 mm workpiece height: 500 mm Table dimensions: 2230 x 670 mm Fodex Afpaspfx Aa Eepd table surface area: 1340 x 400 mm magnetic plate size: 1000 x 410 mm table load: 450 kg throat of the spindle nose: max 330 mm grinding spindle speed: 1440 U/min total power requirement: 18,2 kW weight of the machine ca.: 3,5 nur Maschine t dimension machine xH: 1,9 x 3,3 x 2,25 m dimensions electric cabinet LxWxH: 1,0 x 0,4 x 1,4 m Precision surface grinding machine Possible surface grinding operations: -cross grinding; plunge grinding; face grinding and grinding with a straight grinding track Further specifications: -hydraulic table speed, infinitely variable 1...30 or 2...30 m/min. -Largest table stroke 1150 mm -Manual cross feed 0.01 mm -Manual vertical infeed of the grinding wheel 0.002mm and minimum infeed 0.001mm -Automatic infeed 0.001...0.1mm -Largest selectable total infeed amount 5.0mm -Coolant system (tank with pump) -hydr. aggregate -control cabinet *

Condition: ready for operation (used), A Wassmer surface grinding machine for the pre-grinding process in brick production is available. Stages: 1, wheel diameter: 700mm, feed speed: approx. 5m/min, drive: belt. An on-site inspection is possible. Fedpfjyr Rw Nex Aa Ejpd

Condition: good (used), functionality: fully functional, SINUS – Magnet by JUNG model HF 50 RD Fpsdeyr Rfmopfx Aa Ejd Width x Depth: 450 x 175 mm Pitch: 9 mm

Year of construction: 1997, condition: used, Number of sanding units 1 st. sanding width 140 mm Sanding height max. 120 mm LÖWER Molding Intermediate Sanding Machine Model LZ 2 For finishing and intermediate sanding of all types of moldings. Fjdsyn R Itopfx Aa Eopd Particularly fast processing thanks to simultaneous sanding of several moldings side by side. Conveyor belt feed with table extension under the sanding roller. 1 roller unit from above, working width 140 mm, table length 1100 mm, Workpiece thickness adjustment 2 - 120 mm with numerical display, Drive motor 2.2 kW at 1,430 rpm, mandrel 32 mm, Three feed speeds: 6, 12, and 16 m/min, Infeed contact, extraction ports 2 x 100 mm, Operating voltage 400 V, 50 Hz, 3 Ph, air connection 6 bar. NOTE VIDEO: Video NOT original. Shows machine type of the same model from our archive. (Technical data according to the manufacturer - without guarantee!)

Year of construction: 2022, condition: used, Number of sanding units 6 st. sanding width 45-165 mm Sanding height max. 45-92 mm weight 2200 kg Ecoline Q-SAND 6 For sale on behalf of a customer ----- Full text as PDF attachment! Short description: Machine with infeed conveyor and automatic height detection. It has two grinding discs on top and two grinding discs on the bottom, each connected to a brush unit. Fodpfoxyafkex Aa Espd Technical manufacturer's description: Ecoline Q-Sand: the ideal grinder for squared timber and more. Designed to work on both sides of the workpiece with three-dimensional adjustment, the Q-Sand guarantees maximum precision and uniformity. It is equipped with grinding discs, flap brushes, and a double disc for more effective material removal, thus improving adhesion for subsequent treatments. The Q-Sand can be installed in a production line or, due to its complete operational autonomy, can also be used independently. It is also ideal for window frames, beams, and custom-made products, and optimizes processing times with automated systems and advanced production control. ----- Price of the above-mentioned machine available upon request! ----- (Technical specifications according to the manufacturer - without guarantee!) All prices quoted are net prices, excluding VAT. The video is from the manufacturer Ecoline and shows a new machine.

Condition: used, Year of construction: 1990, functionality: fully functional, machine/vehicle number: 21240, grinding length: 600 mm, grinding width: 375 mm, grinding height: 375 mm, table load: 300 kg, rotational speed (max.): 2,800 rpm, rotational speed (min.): 1,400 rpm, space requirement height: 2,650 mm, space requirement length: 3,800 mm, space requirement width: 2,300 mm, Equipment: documentation/manual, Elb-Schliff Optimal 6375 A well-maintained and fully functional grinding machine with accessories is offered: Fpedjyr D Twspfx Aa Eod • With integrated grinding wheel dresser • 4 grinding wheels with different grain sizes as well as a diamond grinding wheel • Various flap blocks for grinding smaller workpieces • 1 grinding vise • Grinding wheel balancing device • Wiring diagram and documentation

Condition: good (used), STARR ll Surface Grinder Machine: Table Dimensions - 600/250 mm Fjdpfxjiau Ruo Aa Eopd Machine Dimensions (LxWxH): 2700x1800x2000 mm Weight: aprox. 3000 kg

Condition: good (used), Surface Grinding Machine Stock number: 3085 Brand: Geibel & Hotz Year of manufacture: 2015 Machine number: 4051 1015 Model: FS 640 Z CB Grinding length: 600 mm Grinding width: 400 mm Distance table to spindle centre: 140 to 725 mm Table load capacity: 600 kg Magnet: 600 x 400 mm Table longitudinal travel: 200 to 650 mm Table drive: via toothed belt Table speed: 5 to 35 m/min Vertical drive: electromechanical with ball screw Fpodpfxjyryf Ns Aa Ejd Vertical feed speed: 50 to 4,000 mm/min Smallest feed increment: 0.001 mm Measuring system: motor measuring system Max. cross travel: 400 mm Drive: ball screw with backlash-free toothed belt Cross feed speed: 50 to 2,000 mm/min Cross adjustment: electric handwheel and direction pressure buttons Vertical feed speed: 50 to 2,000 mm/min Measuring system: motor measuring system Grinding spindle: 7 kW Grinding wheel dimensions: 300 x 50 x 76.2 mm Grinding wheel speeds: 600 to 3,180 rpm Equipment: separate control cabinet, partial enclosure Note: Machine is supplied without magnetic separator and coolant system, was previously connected to a central system at the company. Condition: Machine can be inspected under power, video available via WhatsApp Connection: 15 kW Machine weight: 2.4 t Machine dimensions: 3,300 x 2,000 x 2,200 (+800) mm

Condition: good (used), Stock number: 3071 Manufacturer: WMW Mikromat Fpjdpjygl Tnjfx Aa Esd Machine number: 3402-1/21.29 Type / Model: SFW 200 x 600 Table size: 200 x 600 mm Grinding area: 600 x 200 mm Maximum grinding height: 400 mm Magnet: 600 x 200 mm Grinding wheels: 200 x 20 x 51 mm Table speed: 2 to 18 m/min Automatic cross feed of table: 0.1 to 2 mm Max. distance table to spindle center: 500 mm Grinding wheel speed: 2,800 rpm Power connection: 3.5 kW Accessories/Equipment: Electromagnet Condition: Good Weight: 1.1 t Machine dimensions: 1,600 x 1,000 x 1,800 mm Dimensions incl. control panel: 2,400 x 1,000 x 1,800 mm

Condition: good (used), Year of construction: 1992, Favretto MB 130 – Technical Specifications Machine type: tangential (horizontal) surface grinding machine Year of manufacture: 1992 Table size: 1700 × 400 mm Magnetic chuck size: approximately 1300 × 400 mm Magnetic plate height: 40 mm Longitudinal travel (X-axis): 1380 mm Cross travel (Y-axis): 450 mm Vertical travel (Z-axis): 550 mm Distance between spindle center and table surface: 203 mm (min) to 753 mm (max) Grinding wheel dimensions: 400 mm diameter × 152 mm width × 100 mm bore Spindle speed: approximately 1400 rpm Fpedjt Rwvzspfx Aa Eed Longitudinal feed rate: 2000 to 40000 mm/min Cross feed rate: 50 to 3000 mm/min Vertical feed rate: 700 mm/min Grinding head motor power: approximately 15 kW Total installed power: approximately 25 kW Maximum table load without magnetic chuck: approximately 1500 kg Maximum table load with magnetic chuck: approximately 1205 kg Overall grinding capacity (L × W × H): approximately 1500 × 600 × 550 mm Machine weight: approximately 7100 kg

Year of construction: 2022, condition: used, Number of sanding units 6 st. Sanding height max. 120 mm Fodpfjynnttex Aa Ejpd output 12 kw

Condition: new, neu ca. 6 Monate ab Auftragse Taiwan 84310 € 1593.46 € 460 mm 395 mm 460 x 200 mm 450 x 200 mm 0 - 20 m/min 0 - 3000 mm/min 0,001 mm 220 mm 290 mm 0 - 3000 mm/min 0.001 mm 1000 - 7000 1/min Fsdpfx Asynnc Iea Eepd 3 kW 2280 mm 2205 mm 2020 mm 1500 kg 1060 mm 175 kg 210 kg Dm. 205 x 12,7 x 31,75 mm 1,1 kW 2.4 kW 0,004 mm 0,003 mm Smart i control with 10.4" touchscreen on a swiveling panel, with electronic wired handwheel - RS232, USB I/O connection - SMART Grind Cam (dxf transfer in G code) -PC based control with graphical dialog programming or G-code programming Infinitely variable speed Surface grinding cycle, cross grinding cycle, plunge grinding cycle, multiple groove grinding cycle, contour grinding cycle, dressing cycle Spindle with 4 angular contact ball bearings (P4, checkout 7) Longitudinal guides with double V shape, with Turcite-B coating All 3 axix with precision ball screws (class C2) and AC servo motors Fully enclosed splash guard with lamp Electromagnetic chuck plate Coolant system with automatic paper filter and magnetic separator autom. dressing attachment table mounted with compensation * Grinding wheel Grinding wheel flange Grinding wheel balancing stand Machine and equipment in accordance with CE regulations Operating manual in GERMAN or ENGLISH * The exact configuration of the dresser must be clarified before ordering

Year of construction: 2011, condition: used, functionality: fully functional, • Band running direction: LEFT to RIGHT, year 2011 #2010037 • 10 face grinding supports, 130 & 150 mm, with vertical oscillation • Horizontal oscillation for material thicknesses up to 100 mm • 1 lower & 1 upper chamfer milling support Fodsyruvcspfx Aa Espd • 2 pneumatic lower & 2 upper chamfer supports • Belt infeed: motorised calibration/profile support • Belt outfeed: motorised drip rail support • Table widening console • Space requirement approx.: 725 x 180 cm

Condition: ready for operation (used), Year of construction: 1989, grinding belt length: 2,600 mm, grinding belt width: 150 mm, space requirement width: 900 mm, space requirement length: 1,650 mm, Langzauner LZK 3/2 edge sanding machine motor power 2,2kW Belt dimension 2600 x 150 mm Belt speed 20m /sec Table dimensions 1000 x 350 mm Height adjustment 200 mm Weight 300 kg Fpsdpfx Ajrgpw Aja Ejd Space requirement 1650 x 900 mm Sanding unit 45° tiltable Veneer sanding unit Oscillation Feed console year of construction 1989 Condition: fully functional

Condition: used, Year of construction: 1989, Technical details: grinding length: 600 mm grinding width: 300 mm workpiece height: 550 mm base plate surface area: 1020x250 mm X-axis : 720 mm y-axis: 550 mm z-axis: 300 mm speeds:: 2900 rpm total power requirement: 8 kW weight of the machine ca.: 2,5 t Fedpfx Asynktioa Ejpd

Condition: used, Year of construction: 2001, Abrasive belt length 1st unit: 2,150 mm Max. working width: 1,300 mm Number of belts: 3 Belt 1st unit: cross belt Design 1st unit: cross belt Sanding pad 1st unit: electronic segmented pad Abrasive belt width 1st unit: 150 x 4,800 mm Fodpfx Aajxzi S Ns Eepd Drive 1st unit: kW 2nd unit: longitudinal roller Design 2nd unit: steel calibration roller Abrasive belt length 2nd unit: 2,150 mm Abrasive belt width 2nd unit: 1,350 mm Abrasive belt speed 2nd unit: 18 m/sec 3rd unit: pad unit Design 3rd roller: electronic segmented pressure beam SDS system Sanding pad 3rd unit: electronic segmented, 32 mm width Abrasive belt length 3rd unit: 2,150 mm Abrasive belt width 3rd unit: 1,350 mm Suitable for lacquer sanding: yes Belt air blast: yes Vacuum conveyor: yes Feed speed, fixed: stepless 5 – 15 m/min Control: screen control Electrical/pneumatic belt oscillation: electrical Infeed height: variable (lower table moves) Table height adjustment: electric motor Table height display: digital Working height / feed table height: 880 mm Location: Supplier

Condition: good (used), Year of construction: 2004, functionality: fully functional, grinding length: 500 mm, grinding width: 300 mm, feed length X-axis: 600 mm, feed length Y-axis: 475 mm, feed length Z-axis: 275 mm, table length: 500 mm, overall weight: 3,700 kg, - control SPS NK - electro magnet - coolant device - 3 grinding wheels, some flanges Technische Daten / technical details: Schleiflänge / grinding length 500 mm Schleifbreite / grinding width 300 mm Schleifhöhe / grinding height 475 mm Elektromagnetabmessungen / electro magnet dimensions 500x300 mm Fpsdpfxowrmcpo Aa Eed Längsachse X / table travel X 600 mm Querachse Z / cross travel Z 270 mm Vertikalachse Y / vertical travel Y 475 mm Drehzahl Schleifscheibe / speed of grinding wheel 1440/2900 UpM / rpm Schleifscheibe / grinding wheel 300x50x76,2 mm Antriebsleistung Schleifspindel / drive capacity grinding spindle 5,7 kW Gewicht der Maschine ca. / weight ca. 3700 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Year of construction: 2005, condition: ready for operation (used), Two glass sandblasting systems from S.A.G. are available. 1) S.A.G. T4, year of construction: 2005, arrangement: vertical, max. blasting width: 3000mm, max. blasting height: 2250mm, max. glass height: 2400mm, glass thickness range: 3mm-40mm, blasting capacity: approx. 15m²/h, machine dimensions X/Y/Z: approx. 3800mm/3300mm/1900mm, weight: approx. 1550kg. 2) S.A.G. T3, year of construction: 2002, blasting width: 2800mm, blasting height: 1200mm, glass thickness range: 3mm-40mm, machine dimensions X/Y/Z: approx. 4100mm/2300mm/1900mm, weight: approx. 1350kg. Documentation available. An on-site inspection is possible. Fodjyrtamepfx Aa Eopd

Condition: good (used), Year of construction: 1982, 1 used surface and guideway grinding machine Manufacturer: ELB Model: SWDE 30 U CNC Year of manufacture: 1982 / 1999 Control type: CNC Control: Mitsubishi 520 Location: NRW Country of origin: Germany Delivery time: short notice Delivery terms: ex stock TECHNICAL DATA Grinding length: 3000 mm Grinding width: 900 mm Fjdpfsynglbox Aa Ejpd Workpiece height: 600 mm Electromagnetic chuck: 3000 x 900 mm Pole pitch: 18 mm Grinding wheel dimensions: Ø 500 x 100 mm Control: Mitsubishi 520 Total power requirement: 18.5 / 5.5 kW Machine weight approx. 19 t Space requirement approx. 9 x 4.5 x 3.5 m Shipping dimensions approx. 13 x 2.5 x 3.5 m

Condition: used, Year of construction: 1982, grinding length: 600 mm, grinding width: 550 mm, total height: 2,490 mm, feed length X-axis: 600 mm, feed length Y-axis: 470 mm, feed length Z-axis: 600 mm, grinding height: 400 mm, grinding wheel diameter: 400 mm, table length: 1,100 mm, table load: 400 kg, table width: 450 mm, grinding wheel width: 100 mm, spindle speed (max.): 1,400 rpm, spindle speed (min.): 1,400 rpm, overall weight: 5,300 kg, travel distance X-axis: 600 mm, travel distance Y-axis: 470 mm, travel distance Z-axis: 600 mm, rotational speed (max.): 1,400 rpm, rotational speed (min.): 1,400 rpm, grinding spindle speed: 1,400 rpm, disc diameter: 400 mm, space requirement height: 2,490 mm, We are offering this used ELB-Schliff Oprimal 3 ND surface grinding machine, year of manufacture 1982. Maximum grinding length: 600 mm Maximum grinding width: 550 mm Working height with new grinding wheel: 400 mm Working height with worn grinding wheel: 600 mm Spindle taper ratio: 1:5 Manual vertical travel of grinding spindle: 600 mm Manual horizontal travel of grinding spindle: 470 mm Swivel range grinding spindle: 1° Clamping table surface: 1100 x 450 mm Small table stroke: 80 mm Number of T-slots: 1 T-slot width: 16H7 mm Cross feed (table): 470 mm Longitudinal feed (table): 600 mm Table load capacity: 400 kg Outside diameter of grinding wheel: 400 mm Inside diameter of grinding wheel: 127 mm Grinding wheel thickness: 100 mm Recess 1 diameter: 190 mm Recess 1 thickness: 20 mm Recess 2 diameter: 190 mm Recess 2 thickness: 30 mm Machine height: 2.49 m Weight: 4700/5300 kg Direct spindle speed: 1400 min⁻¹ Continuous feed rate, grinding spindle carriage: 1.2 m/min Intermittent feed rate, grinding spindle carriage: 3–60 mm Fpedpfxsyrn Sdo Aa Esd Hydraulic table feed speed: 1–30 m/min If you have any questions or require further information, please feel free to send us a message or call us.

Condition: good (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: 156608, total height: 2,100 mm, total length: 3,000 mm, total width: 2,000 mm, grinding wheel diameter: 250 mm, overall weight: 1,800 kg, SAEILO KENT KGS-63 WMI surface grinding machine - Magnetic table dimensions: 610 x 310 mm Fpsdpfjym Sh Sex Aa Esd Attention: The item must be collected between 21.04. and 30.04.2026 on a binding date to be agreed upon. FCA D-96257 Marktgraitz – loaded onto truck

Condition: used, Year of construction: 2001, grinding length 4200 mm grinding width 1300 mm workpiece height 550 mm Control Siemens 840D passage width 1300 mm electro-magnetic table 4200 x 1300 mm grinding height 550 mm grinding motor 306 kW grinding motor turning speeds up to 370 U/min grinding motor feed, infinitely variable 0,5-35 m/min coolant flow rate 2000 l/min weight of the machine ca. 50 t dimensions of the machine ca. 11,21 x 5,25 x 3,85 m Equipment / Accessories: Fjdpsthumuefx Aa Ejpd - segment head - diameter 1400 mm - for segment dimensions 120/106 x 41 x 250 mm - number of segments: 1 set = 26 pieces - grinding motor adjustment - in steps: 0,002 - 1 mm - continuous: up to 5 mm/min stepless