Used Presona Ab Baler for sale (11,864)

Condition: reconditioned (used), Year of construction: 2015, operating hours: 28,748 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, power: 37 kW (50.31 HP), volume flow: 350 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Gsdovn Tg Ijpfx Ankjub Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2008, operating hours: 24,629 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,650 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 24,000 kg, transport height: 3,000 mm, oil tank capacity: 2,000 l, power: 90 kW (122.37 HP), volume flow: 1,350 m³/h, transport width: 2,400 mm, transport length: 10,000 mm, Good day, We hereby offer you, without obligation, a used baling press from the manufacturer Presona AB, model LP 100 CH2 S. The following technical data has been taken from the manufacturer’s operating manual and brochures. We cannot guarantee the accuracy or completeness of this information. Manufacturer: Presona AB, Sweden Model: LP 100 CH2 S Year of manufacture: 2008 Gusdpsymmmpjfx Ankob Total operating hours: 24,629 hours (as of February 2026) Effective pump operating hours: 10,090 hours Main press force: 100 t Specific compaction force: 81 N/cm² Pre-press flap force: 50 t Fill chute dimensions: 1,650 x 1,100 mm Fill volume per press cycle: 3 m³ Bale dimensions: 1,100 x 1,100 mm Drive power: 2 x 45 kW Tying: 5-fold vertical Hydraulic oil tank capacity: 2,000 L Transport weight (press only after disassembly): approx. 25 t Note: The machine was used in a recycling facility for compacting paper, cardboard, and films/foils. The press is in good condition and will be replaced by a new, larger machine in July 2026. Until then, it can be viewed in operation with materials processed. We would be pleased if this press is of interest to you. Your Service Team Mertens & Frowein GmbH

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Gedpjvgrh Uofx Ankeub Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: excellent (used), Year of construction: 2014, operating hours: 37,656 h, functionality: fully functional, pressing force: 85 t, filling opening width: 1,500 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 650 kg, overall weight: 25,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2024, volume flow: 410 m³/h, transport width: 2,400 mm, transport length: 9,300 mm, Hello, We are offering you a used baler from the manufacturer Presona AB, type LP 85 VH1, subject to availability. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot guarantee their accuracy or completeness. Manufacturer: Presona AB, Sweden Type: LP 85 VH1 Year of manufacture: 2014 Total operating hours: 37,565 hours, as of March 2025 Guedpfxov T I Evs Ankob Main press force: 85 t Specific press force: 100 N/cm² Pre-press flap force: 28 t Feed chute dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying system: 5-fold vertical Hydraulic oil tank volume: 1,000 L Press dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Press weight: approx. 25 t Note: The machine was used for compaction at a recycling plant. Used for the production of paper, cardboard, films, and plastics such as bottles, buckets, canisters, and drums. The press is in good condition. Many wear parts and entire assemblies have been replaced over the past three years. The machine has been regularly serviced. We would be pleased if this press is of interest to you. Your service team at Mertens & Frowein GmbH

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material Gujdpfx Asvwlqqjnksb 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,250 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, power: 22 kW (29.91 HP), year of last overhaul: 2025, volume flow: 530 m³/h, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Guodpfx Aey R Npienkjb Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the whirling unit replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2022, operating hours: 100 h, functionality: fully functional, machine/vehicle number: 1074-B-101, Offering fully operational pallet collar production line. Gujdpfxoy Nyx So Ankeb Totally 3 machines: 1. Drill 2. press 3. press Also additionally assembling tools, tables, hinges ect. Possible to see how it works. Line production capacity 600-800 collars per day.

Condition: used, This listing is for an ÄKTA ready™ Chromatography System The unit is in full working condition and is ready for immediate release The ÄKTA ready™ Chromatography System is a single‑use liquid chromatography platform engineered for bioprocessing, process scale‑up, and GMP‑regulated manufacturing of biologics, including monoclonal antibodies, recombinant proteins, viral vectors, nucleic acids, and other sensitive therapeutic products. Key Characteristics Gsdpfxsyhhgas Ankoub - Single‑use disposable flow paths — eliminate the need for cleaning and cleaning validation between runs, reduce downtime, and minimize cross‑contamination risk. - Flexible operation — available in multiple configurations (isocratic, gradient, variable UV, extended) to match different purification needs. - Scalable platform — flow kits for low and high flow rates support a wide range of process volumes; systems scale from small‑batch purification to larger process requirements when paired with larger ÄKTA ready™ XL models. - Designed for GMP environments — extensive documentation and regulatory support help meet compliance demands in regulated biopharmaceutical production

Condition: used, Year of construction: 2011, operating hours: 85,000 h, functionality: fully functional, fuel type: gas, output voltage: 400 V, output frequency: 50 Hz, Full trigeneration plant with York absorption chiller. Regularly maintained and covered by the supplier’s preventive and corrective maintenance contract. Major overhaul performed in 2021 at 61,000 operating hours. New Long Block (LB) supplied by INNIO on the occasion of the major overhaul, documentation available. • 87,670 plant hours; • 26,904 engine hours; The crankshaft has not been machined, while the engine block has been machined for the use of oversized liners. Overhauled alternator, report available. Price and further information available upon request. Gusdpjy Ibldofx Ankeb

Year of construction: 1986, condition: excellent (used), machine/vehicle number: 1767, Further MACHINERY / SPARE PARTS & MACHINE COMPONENTS of this type are available in our warehouse. ON REQUEST Gujdpepitfxofx Ankob

Condition: used, Pizza ovens – (without steam injection) We have 5 units – used. From our own operation. Suitable for flammkuchen, pizza, lahmacun, etc. Used until recently, ready for immediate use, only test run possible. Gujdpsyg N D Dsfx Anksb

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, travel distance X-axis: 650 mm, travel distance Y-axis: 480 mm, travel distance Z-axis: 475 mm, table width: 450 mm, table length: 1,200 mm, table load: 400 kg, overall weight: 2,300 kg, We offer this used Abene Machine Ab VHF-360Ti milling machine, year of construction 2011. Serial number: 36120 Guodey Hgnhspfx Ankjb Year of manufacture: 2011 Heidenhain TNC620-control Table size 1200 x 450 mm Max load 400 kg X-travel 650 mm, Y-travel 480 mm, Z-travel 475 mm Spindle BT40 Main motor 7,5 kW Weigth 2300 kg Excellent condition If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: good (used), functionality: fully functional, Year of construction: 2017, operating hours: 472 h, power: 60 kW (81.58 HP), load capacity: 750 kg, lifting height: 26,000 mm, lifting power: 750 kg/m, platform length: 5,480 mm, platform width: 2,440 mm, overall weight: 19,800 kg, transport length: 5,960 mm, transport width: 2,500 mm, transport height: 3,200 mm, fuel type: electric, wheelbase: 4,100 mm, Equipment: all wheel drive, === KEY SPECIFICATIONS === Year of manufacture: 2017 Operating hours: 472 h Machine width: 2.50 m Drive system: 4x4 Driveable at full height: Yes Extendable platform: Yes (2.13 m) Power output: Electric drive, 80 V / 750 Ah Working height: 28.00 m Platform capacity: 750 kg Drive type: Electric – Hydraulic Battery type: Lead-acid Self-levelling outriggers: Yes Platform dimensions (L x W): 5.48 × 2.44 m Tyre type: Non-marking CE certified: Yes Weight: 19,800 kg Indoor / Outdoor use: Both === HIGHLIGHTS === Selected from a professional fleet with verifiable technical data CE-certified machine Driveable at full working height High platform capacity suitable for heavy-duty applications === CONDITION === Machine is in original operational condition. Electric drive system fully functional. Battery system present (80 V / 750 Ah). Available directly from stock in Sittard. === LOCATION & DELIVERY === Located in Sittard, The Netherlands. Worldwide transport available. Price on request (EXW / excl. VAT). Reliable heavy-duty electric scissor lift designed for demanding indoor and outdoor applications. High load capacity, full-height drivability and extendable platform ensure maximum productivity. Machine is CE-certified and ready for immediate deployment. === DELIVERY === Crane loading available on request. Flexible transport solutions available depending on destination. Guedpfx Ansx Ivqnokjb Logistics handled by Collé Rental & Sales.

Condition: good (used), functionality: fully functional, Year of construction: 2017, operating hours: 6,934 h, load capacity: 750 kg, lifting height: 20,500 mm, lifting power: 750 kg/m, platform length: 4,300 mm, platform width: 2,400 mm, overall weight: 11,000 kg, transport length: 4,600 mm, transport width: 2,450 mm, transport height: 2,970 mm, fuel type: diesel, tire condition: 75 %, wheelbase: 3,140 mm, Equipment: all wheel drive, === KEY SPECIFICATIONS === Year of manufacture: 2017 Operating hours: 6,934 h Machine width: approx. 2.45 m Drive: 4x4 Driveable at full height: Yes Extendable platform: Yes Guedpox Ihicjfx Ankeb Engine power: Diesel (manufacturer on request) Working height: 22.5 m Platform capacity: 750 kg Drive type: Diesel Battery type: N/A (diesel powered) Self-levelling outriggers: Yes (WDS system) Platform dimensions (L × W): 4.30 × 2.40 m Tyre type: Rough terrain (non-marking: no) CE certified: Yes Weight: approx. 11,000 kg Indoor / outdoor use: Outdoor === HIGHLIGHTS === Carefully selected machine with verifiable history CE-certified and compliant with European safety standards Equipped with self-levelling hydraulic outriggers (WDS) High platform capacity for heavy-duty applications Ready for immediate transport and operation === CONDITION === Machine in original working condition. Diesel engine and hydraulic system operate correctly. Tyres in good condition (approx. 75% tread remaining). Available directly from stock. === LOCATION & DELIVERY === Located in Sittard, The Netherlands Worldwide delivery possible Price on request (EXW / excl. VAT) Reliable AB Lift S225-24 D4 WDS diesel scissor lift for demanding outdoor applications. Thanks to its 4x4 drive, self-levelling outriggers and high platform capacity, this machine is ideally suited for construction, industrial and infrastructure work. All machines from Collé Rental & Sales are professionally inspected and ready for immediate use. Spare parts, service and technical support available on request. === DELIVERY OPTIONS === Crane loading available on request Flexible transport solutions tailored to destination and logistics Transport professionally arranged by the Collé Rental & Sales logistics team

Condition: good (used), functionality: fully functional, Year of construction: 2019, operating hours: 496 h, load capacity: 750 kg, lifting height: 14,300 mm, lifting power: 750 kg/m, platform length: 4,500 mm, platform width: 2,360 mm, overall weight: 9,000 kg, transport length: 4,840 mm, transport width: 2,460 mm, transport height: 2,370 mm, fuel type: electric, tire condition: 85 %, wheelbase: 3,200 mm, color: blue, Equipment: UVV, === KEY SPECIFICATIONS === Year of manufacture: 2019 Operating hours: 496 h Machine width: 2.46 m Drive system: 2WD (two-wheel drive) Driveable at full height: Yes Extendable platform: Yes (up to 2.70 m) Power output: Electric drive, 80 V / 540 Ah Working height: 16.30 m Platform capacity: 750 kg Drive type: Electric Battery type: Lead-acid Self-levelling outriggers: No Platform dimensions (L × W): 4.50 × 2.36 m Tyre type: Non-marking CE certification: Yes Weight: approx. 9,000 kg Indoor / Outdoor use: Both (Indoor & Outdoor) === HIGHLIGHTS === Carefully selected from reliable sources with verifiable history CE certified, full documentation included Ready for immediate transport and operation Comprehensive technical documentation available === CONDITION === Clean, original condition with well-maintained systems. Battery tested and in good working condition. Immediately available from stock in Sittard. === LOCATION & DELIVERY === Located in Sittard, the Netherlands. Worldwide delivery available. Price on request (EXW / excl. VAT). Guodox Nhvrspfx Ankjb Reliable electric scissor lift with high platform capacity and compact design. Ideal for indoor and outdoor applications where low emissions and quiet operation are required. All machines are fully inspected, CE approved and ready for immediate deployment. Spare parts and professional technical assistance available on request. === DELIVERY === Crane loading available on request. Flexible shipping options tailored to your destination. All transport handled by Collé Rental & Sales.

Condition: good (used), functionality: fully functional, Year of construction: 2020, load capacity: 600 kg, lifting height: 30,000 mm, lifting power: 600 kg/m, platform length: 5,800 mm, platform width: 1,200 mm, overall weight: 21,500 kg, transport length: 6,420 mm, transport width: 1,390 mm, transport height: 3,190 mm, construction height: 3,190 mm, fuel type: electric, tire condition: 80 %, wheelbase: 4,870 mm, ground clearance: 200 mm, color: blue, Equipment: all wheel drive, === KEY SPECIFICATIONS === Year of manufacture: 2020 Operating hours: On request Machine width: 1.39 m Drive system: 4x4 (4WD) with 4-wheel steering (4WS) Driveable at full height: Yes Extendable platform: Yes (1.90 m extension) Power output: Electric drive, 80 V / 560 Ah Working height: 32.00 m Platform capacity: 600 kg Drive type: Electric Battery type: Lead-acid Self-levelling outriggers: Yes Platform dimensions (L × W): 5.80 × 1.20 m Tyre type: Non-marking (solid) CE certification: Yes Weight: 21,500 kg Indoor / Outdoor use: Indoor & Outdoor === HIGHLIGHTS === Gsdpfxox Nft Io Ankoub Carefully selected from reliable sources with verifiable history CE certified, full documentation included Ready for immediate transport and operation Comprehensive technical documentation available === CONDITION === Clean, original condition with well-maintained systems. Batteries tested and in good working condition. Immediately available from stock in Sittard. === LOCATION & DELIVERY === Located in Sittard, the Netherlands. Worldwide delivery available. Price on request (EXW / excl. VAT). Reliable machines from trusted sources, supported by professional technical expertise. All machines are fully inspected, CE approved and ready for immediate deployment. Spare parts and professional assistance available on request. === DELIVERY === Crane loading available on request. Flexible shipping options tailored to your destination. All transport handled by Collé Rental & Sales logistics team.

Condition: good (used), Year of construction: 2018, functionality: fully functional, Baler Presona LP 85 VH2 with cross tying, year of construction 2018 Technical data: Manufacturer: Presona Sweden Model: LP 85 VH2 Year of construction: 2018 Guodpfxjyz Snpe Anksb Drive power: 2 x 45 kW Operating hours: 40,350 Effective operating hours: approx. 22,000 Pre-press force: 28 t Main press force: 85 t Feed opening: 1500 x 1100 mm Bale dimensions: 750 x 1100 mm Bale weight: 450 - 650 kg Theoretical throughput: 1,200 cbm/h Throughput at 30–100 kg/cbm: 13–30 t/h Tying: 5-fold vertical, 3-fold horizontal Oil tank volume: 2,000 L Transport dimensions of press: 10,400 x 2,400 x 2,800 mm (LxWxH) Weight: approx. 27,000 kg The baler was dismantled from running operation. Technical documentation is available. Please note: All technical data is based on manufacturer’s specifications. We accept no liability for the accuracy of the information provided or for possible errors. The offer is subject to change, prior sale reserved, and can be revoked at any time. Inspections are possible by prior arrangement. Sale is ex works, payment in advance, without warranty or guarantee.

Condition: good (used), Fan model: HPB-F-040-300T Gujdeyz Tc Iopfx Ankob Motor model: SKh90-2S2 Latest use: Air cushion table External dimensions: Width: 700 mm. Depth: 450 mm. Height: 450 mm. Weight: approx. 20 kg. Condition: good, second-hand

Condition: ready for operation (used), Load capacity: 1000 kg Lifting range: 85 - 650 mm Fork length: 1150 mm Fork width: 160 mm Guedpfx Anod Ax I Dsksb carrying width: 510 mm Total length: 1500 mm Total height: 1250 mm

Condition: good (used), Renz Autobind AB 700 + KAS 500 Semi-Automatic Spiral Binding Machine Machine in very good condition, ready to operate. Efficient semi-automatic machine for the production of calendars, notebooks, and other metal spiral-bound products. Fast operation Spin diameters range from 3/16″ to 1 1/8″ Working width up to 700 mm Crimping thickness approx. 23 mm Capacity up to 1200 cycles/hour The semi-automatic machine unwinds the spiral from the spool, counts the stitches, cuts the spiral to the pre-set stitch count, and transfers the spiral section to the crimping area. The operator places the pre-perforated calendar on the table. Guodpfx Anoywdrfjkjb The calendar is automatically transferred to the crimping area by pressing the pedal. Includes a KAS 500 hanger feeder Power supply: 230V + compressed air Weight: 615 kg.

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, Equipment: documentation/manual, type plate available, Liquid smoke dosing device for a smoking chamber; the device is designed for dosing into two chambers. Gjdpfx Asw Emd Hjnkjub

Condition: new, Year of construction: 2025, Z-MaT DT500E-S, Siemens 828 D ShopTurn 15" Touch CNC Turning Center, with Sub-Spindle, Driven Tools, and True Y-Axis, 35° Slant Bed Max. Swing Diameter: 650 mm Max. Turning Diameter: 320 mm Max. Turning Length: 550 mm Linear Roller Guides on All Axes Rapid Traverse X/Z/Y: 20/20/12 m/min Y-Axis Travel: 140 mm, +/- 70 mm Turret: 12 Stations BMT55 — 12 Driven Positions Max. Turret Speed: 4000 rpm, 3 kW Main Spindle: Chuck Diameter: 254 mm Spindle Nose: A2-8 Max. Bar Capacity: 75 mm Spindle Bore Diameter: 86 mm Spindle Drive Power, Direct Drive: 15/16 kW Max. Spindle Speed: 3500 rpm Sub-Spindle: Chuck Diameter: 152 mm Spindle Nose Standard: A2-5 Max. Bar Capacity: 46 mm Drive Power: 11 kW Max. Speed: 3000 rpm Dimensions (W x D x H): 3.1 x 2.0 x 2.25 m Weight: 5.3 t Standard Equipment: Parts Catcher (Preparation) Hinged Belt Chip Conveyor Oil Skimmer Coolant System 3-Color Warning Light Work Area Lighting Centralized Lubrication System Programmable Tailstock Set of Soft Jaws Tools and Toolbox CE Conformity Guodpfx Aewwvldsnkjb Operating Manual The machine will be exhibited at EMO, Hall 12/D10 and will be available immediately afterwards. A wide range of automation options is available, such as bar loaders and loading robots.

Condition: new, Year of construction: 2024, DT500EY-650 Siemens 828 D ShopTurn (Fanuc Option) CNC turning/milling center with tailstock, driven tools and true Y-axis, ±70 mm, 35° slant bed and linear roller guides Available for viewing in the showroom Max. swing diameter: 600 mm Max. turning diameter: 320 mm Max. turning length: 650 mm Rapid traverse X/Z/Y: 20/20/12 m/min Turret: 12 stations BMT55, all 12 with live tooling Max. rotational speed: 4000 rpm, 3 kW Spindle Chuck diameter: 203 mm (optional 254 mm) Spindle nose: A2-6 (optional A2-8) Max. bar capacity: 52 mm (options for 65, 75, and 91 mm) Spindle bore diameter: 66 mm Drive power, direct drive: 22/30 kW Max. spindle speed: 4,000 rpm Tailstock diameter: 110 mm / MK3 Tailstock traverse: 850 mm Dimensions (W x D x H): 3.6 x 2.1 x 2.3 m Weight: 5.5 t Standard accessories: Coolant system Three-color warning light Work area lighting Central lubrication Programmable tailstock Set of soft jaws Tools and toolbox CE conformity Gujdjqa Dtfepfx Anksb Operating manual Including special accessories: Hinged belt chip conveyor Tool measuring arm Oil skimmer Bar loader interface Video shows DT500

Condition: used, functionality: fully functional, Year of construction: 2010, machine/vehicle number: 2455698, power: 41 kW (55.74 HP), load capacity: 750 kg, mast type: telescopic, lifting height: 26,000 mm, platform length: 5,480 mm, platform width: 2,440 mm, overall weight: 18,000 kg, transport length: 5,960 mm, transport width: 2,500 mm, transport height: 3,200 mm, fuel type: diesel, color: red, Technical data Year of manufacture: 2010 Gusdpfeyqzrzex Ankeb Engine: Diesel Working height: 28.00 m Platform height: 26.00 m Platform extension: 2.13 m Platform dimensions (L x W): 5.48 m x 2.44 m Overall dimensions (L x W x H): 5.96 m x 2.50 m x 3.20 m Load capacity: 750 kg Controls: Proportional Climbing ability: 40% Weight: 18,000 kg Travel speed: 0.7 - 4.0 km/h All-wheel drive General signs of use, fully functional

Condition: ready for operation (used), Year of construction: 1981, machine/vehicle number: S 659, functionality: fully functional, fully functional in good condition Guedpfxsyr E She Ankob