Used Kraussmaffei Km-650-3500 C-2 for sale (100,830)

Condition: used, Year of construction: 2005, Technical details: screw size: 90 mm injection shot weight in Polysterol: 1.758 g/PS closing pressure: 6500 kN weight of the machine ca.: 32 t Out of serial production Codpfxetunccj Akbjgu *

Condition: reconditioned (used), Year of construction: 2004, Krauss-Maffei KM 650-3500 C 1 Cgjdpfxohy Nnbo Akbju 650 tons Krauss-Maffei injection moulding machine from 2004 with 45.000 working hours in automatic-cycle. Machine will be delivered full checked tested and reconditioned by our team. Equipment: 6 neum. cscade, 24 hot runner zones, 1 core in fix platen, 1 core in moving platen, electrical screw-drive. Ask us for the start up service with warranty of working condition. Technical details CLAMPING FORCE 6.500 kN PLATEN SIZE 1.540 x 1.440 mm DISTANCE BETWEEN TIE BARS (h x v) 1.110 x 960 mm TRAVEL OPENING 1.150 mm DAYLIGHT MAX 1.750 mm SCREW DIAMETER 90 mm MIN. MOULD HIGHT 600 mm YEAR OF BUILDING 2004 INJECTION VOLUMEN 1.953 cm3 SHOTWEIGHT 1.777 grms INJECTION PRESSURE 1.742 bar This machine will be delivered complete checked, repaired and tested at our workshop and can be shown under power !

Condition: excellent (used), Year of construction: 2007, Manufacturer: Krauss Maffei Type: KM 650-3500-700 CZ Year of manufacture: 2007 Control system: MC 4 Clamping Unit: Clamping force: 650 t Opening stroke: 1,150 mm Minimum mold installation height: 600 mm Maximum platen daylight: 1,750 mm Tie bar spacing (h x v): 1,100 x 900 mm Platen dimensions (h x v): 1,510 x 1,370 mm Cgedpfsx Uqa Dex Akbeu Centering (nozzle-ejector plate): 200 / 200 mm 1st Injection Unit: Screw diameter: 80 mm Maximum shot weight in PS: 1,400 g Shot volume: 1,543 cm³ Injection pressure: 2,205 bar 2nd Injection Unit: Screw diameter: 45 mm Shot weight in polystyrene: 278 g Shot volume: 305 cm³ Injection pressure: 2,336 bar Accessories: 2 x air valves 16-fold cascade 3 x core pullers on moving platen 3 x core pullers on fixed platen 20 x hot runner controllers Robot interface: Euromap 67 Dimensions: Total weight: 34,500 kg Overall size (L x W x H): 7.8 x 2.5 x 2.5 m Operating hours: 45,400 h Machine can also be operated as a single-component machine (1K).

Condition: like new (used), Year of construction: 2007, operating hours: 27,000 h, clamping force: 6,500 kN, KraussMaffei KM650-3500 C2 injection molding machine for sale. The machine is in very good condition. It has only been operated in single-shift production and used exclusively for small batch and sample production. A new hydraulic pump was recently installed (approx. 300 operating hours ago). - 27,000 operating hours - Year of manufacture: 2007 - MC4 control system - Core pulls on both sides - Tie bars and guideways are undamaged and in like-new condition - Robot with longitudinal take-out LR300 and conveyor belt - Proportional valves, HPS screw, bimetallic cylinder - Total weight approx. 30,000 kg - Opening stroke: 1,150 mm Adapter plates are also available from us. Inspection under power is possible. Other accessories such as Motan dryer, chiller unit, and much more available upon request. Cjdpfx Akjyn Sc Eobegu The machine can be dismantled and loaded by us upon agreement. We look forward to your inquiry.

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, clamping force: 6,500 kN, screw diameter: 70 mm, injection pressure: 2,389 bar, ejector stroke: 135 mm, opening stroke: 1,825 mm, TECHNICAL DETAILS Clamping Unit Clamping force: 6,500 kN Maximum mold opening force: 346 kN Moving platen opening force: 169 kN Moving platen closing force: 144 kN Mounting platen (H x V): 1,520 x 1,470 mm Clear distance (H x V): 1,000 x 930 mm Mold opening stroke: 1,150 mm Minimum mold installation height: 675 mm Codpfx Ajycqc Tjkbjgu Daylight: 1,825 mm Ejector stroke: 135 mm Ejector force forward/backward: 226 kN Injection Unit Screw diameter: 70 mm L/D ratio: 23 Injection pressure: 2,389 bar Shot volume: 1,097 cm³ Shot weight (PS): 998 g Injection flow rate: 393 cm³/s Screw speed: 218 rpm Plasticizing rate: 83 g/s Nozzle contact force: 173 kN MACHINE DETAILS Dimensions & Weight Required floor space approx.: 8.70 x 2.90 x 2.80 m Total weight: 44,000 kg Electrohydraulic Equipment Rated power pump motor: 75 kW Installed heating capacity: 36 kW Temperature control zones cylinder heating: 7 EQUIPMENT Oscillating elements 1 x air valve 8-fold pneumatic cascade control Accumulators 2 x hydraulic core pulls at BWAP 2 x hydraulic core pulls at FWAP Robot interface according to EUROMAP 67

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, clamping force: 6,500 kN, screw diameter: 70 mm, Clamping unit: Clamping force 6500 kN Mould opening force, max. 346 kN Travel force movable platen opening 169 kN Travel force movable platen closing 144 kN Size of mould platens (h x v) 1520 x 1470 mm Distance between tie bars (h x v) 1000 x 930 mm Mould opening stroke 1150 mm Mould height min 675 mm Max. daylight 1825 mm Hydraulic ejector - stroke 135 mm Ejector force 226 kN Injection unit: Screw diameter 70 mm Ls/D ratio 23 Injection pressure 2389 bar Stroke volume 1097 ccm Shot weight (PS) 998 gr. Injection rate 393 ccm/s Screw speed 218 1/min Plasticising rate max. 83 g/s Nozzle pressure 173 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 75 kW Installed heating capacity 36 kW Csdpfx Aev Stbmokbegu Adjustable barrel heating zones 7 Dimensions and weights: Dimensions of the machine ca. 8,70 x 2,90 x 2,80 m Total machine weight 44000 kg Accessories: - Anti vibration pads Additional options: - 1 x air valve - 8 x pneumatic sequentional valves - Accumulator - 2 x hydr. core pulls on movable plate - 2 x hydr. core pulls on fix plate - Robot interface according to EUROMAP 67

Condition: excellent (used), Year of construction: 2014, operating hours: 47,137 h, functionality: fully functional, machine/vehicle number: 61020607, clamping force: 1,300 kN, clearance between the columns: 470 mm, Here we, as dealers in injection moulding machines, offer the following well-maintained used injection moulding machine for sale. Of course, we also purchase well-maintained injection moulding machines from model year 2010 onwards. We have been wholesalers of used injection moulding machines for over 25 years. Important current notice – Tax information and benefit for used machines: From 01.07.2025, used machines will also be eligible for a special tax depreciation of 30% per year. In addition to the lower price compared to a new machine, you can claim the same depreciation amounts as for a new machine. Keyword: Growth booster (§ 7 paragraph 2 EStG-E). Manufacturer: Krauss Maffei Model: KM 130 750-130 CXV BluePower 2-color 2-component machine Control system: MC6 Year: 2014 Machine no.: 61020507 Operating hours: 47,137 h Complete maintenance records for the last 7 years / 25,000 operating hours 1st injection unit 750 horizontal Screw diameter: 50 mm Injection volume: 393 ccm Shot weight: 357 g Heating capacity: kW Heating zones: 5 Nozzle stroke: mm Injection pressure: 1,892 bar 2nd injection unit 180 vertical Screw diameter: 30 mm Injection volume: 85 ccm Cgedpfxjyf Uy Uo Akbju Shot weight: 77 g Injection pressure: 2,500 bar Clamping unit Clamping force: 130 t / 1,300 kN Opening stroke: 600 mm Tie bar spacing: 470 x 470 mm Plate size: 745 x 770 mm Max. daylight: 900 mm Min. mould installation height: 300 mm Ejector stroke: 150 mm / ejector force: 23 kN Dimensions: 4.39 x 1.61 x 4.01 m Weight: 9,000 kg Extras – complete machine data sheet attached as PDF document Nozzle side: Needle shut-off A+C 1 x hydraulic core pull 1 x pneumatic core pull 1 x air blast Ejector side: 1 x hydraulic core pull 3 x pneumatic core pulls 1 x air blast Water BGS: 6 circuits each on nozzle and ejector side BluePower technology: up to 40% energy savings The machine is in excellent condition and can be inspected under power. Any peripheral devices shown are NOT included in the offer! The machine is available immediately. Free loaded onto buyer’s truck or delivered free to destination against reimbursement of freight costs. For information about the machines we offer and our company: - We only sell our own machines, purchased from ongoing production, from our warehouse in Hanover - All machines offered are inspected and tested prior to dismantling - We do NOT sell insolvency assets – we are NOT intermediaries trading in third-party property - All machines offered come from successful companies for whom regular maintenance is a given - All offered machines are available for viewing at our warehouse

Condition: ready for operation (used), Year of construction: 1997, Stock-No. 13602 Manufacturer Krauss Maffei Type of machine KM 650 – 8000 CM Year 1997 Working hours 80000 h Controlversion MC 3-F Screentext German Location Eschweiler - Germany Clamping unit: Clamping force 6500 kN Mould opening force, max. 346 kN Travel force movable platen opening 169 kN Travel force movable platen closing 144 kN Size of mould platens (h x v) 1704 x 1700 mm Distance between tie bars (h x v) 930 x 930 mm Mould opening stroke 1150 mm Mould height min 600 mm Max. daylight 1750 mm Hydraulic ejector - stroke 250 mm Ejector force 226 kN Injection unit: Screw diameter 130 mm Ls/D ratio 20 Injection pressure 1296 bar Stroke volume 6172 ccm Shot weight (PS) 5617 gr. Injection rate 1540 ccm/s Screw speed 138 1/min Plasticising rate max. 238 g/s Nozzle pressure 246 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 132 kW Installed heating capacity 70 kW Adjustable barrel heating zones 7 Dimensions and weights: Dimensions of the machine ca. 12,00 x 2,80 x 2,70 m Total machine weight 43000 kg Accessories: - Anti vibration pads Additional Options: - 1 x air valve - 2 x core pulls on movable plate Codpfoub S R Hsx Akbegu - 2 x core pulls on fix plate - 8 x hotrunner controller - Robot interface according to Euromap 67

Condition: used, Year of construction: 2010, Injection moulding machine Krauss Maffei KM 650-4300, year 2010 Cjdpfew Hwthjx Akbsgu

Condition: reconditioned (used), Year of construction: 2002, functionality: fully functional, machine/vehicle number: 504212, clamping force: 5,000 kN, screw diameter: 90 mm, clearance between the columns: 900 mm, injection pressure: 1,742 bar, installation height: 480 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Clamping Unit Clamping force: 5,000 kN Tie bar distance (h x v): 900 x 800 mm Maximum mold opening distance: 1,170 mm Minimum mold installation height: 480 mm Platen opening stroke: 1,650 mm Ejector stroke: 250 mm Ejector force: 95 kN Reverse ejector force: 48 kN Injection Unit Screw diameter: 90 mm L/D ratio: 20 Injection pressure: 1,742 bar Injection volume: 1,953 cm³ Shot weight (PS): 1,777 g Injection rate: 649 cm³/s Nozzle contact force: 115 kN MACHINE DETAILS Electrical Data Pump drive power: 90 kW Heating capacity: 44 kW Operating voltage: 400 V Frequency: 50 Hz Total rated current: 306 A Motor rated current: 170 A Operating voltage: 3 phases Cedpfx Aow Dy Rwokbsgu Dimensions & Weight Net weight: 25.8 t Machine dimensions (L x W x H): 7.65 x 2.33 x 2.55 m Note: Delivery, installation, and commissioning can be arranged upon request for an additional charge.

Condition: ready for operation (used), Year of construction: 2007, operating hours: 70,000 h, functionality: fully functional, clamping force: 6,500 kN, screw diameter: 95 mm, displacement volume: 3,367 cm³, Clamping force 6500 kN Mould opening force, max. 346 kN Travel force movable platen opening 169 kN Travel force movable platen closing 144 kN Size of mould platens (h x v) 1520 x 1470 mm Distance between tie bars (h x v) 1000 x 930 mm Mould opening stroke 1150 mm Mould height min 600 mm Max. daylight 1750 mm Hydraulic ejector - stroke 250 mm Ejector force 95 kN Injection unit: Screw diameter 96 mm Ls/D ratio 23 Injection pressure 1795 bar Stroke volume 3367 ccm Shot weight (PS) 3064 gr. Injection rate 690 ccm/s Screw speed 153 1/min Plasticising rate max. 104 g/s Nozzle pressure 166 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 50 kW Adjustable barrel heating zones 7 Dimensions and weights: Dimensions of the machine ca. 9,83 x 2,90 x 2,80 m Total machine weight 43170 kg Accessories: - Anti vibration pads - Krauss Maffei Robot LR300 X: 1200 mm, servo Y: 1000/1000 mm, servo Z: 3500 mm, servo C: 0 - 90° - Conveyor - saftey guard Additional options: - 1 x air valve - 6 x pneumatic sequentional valves Cgjdpfxex Hzzcj Akbju - 12 hotrunner controller - 2 x hydr. core pulls on movable plate - 2 x hydr. core pulls on fix plate

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036721, clamping force: 6,500 kN, screw diameter: 70 mm, clearance between the columns: 1,110 mm, displacement volume: 1,078 cm³, injection pressure: 1,877 bar, injection weight: 981 g, opening stroke: 3,200 mm, plate height: 1,540 mm, drive type: Hydraulisch, clear span: 3,200 mm, tool weight: 2,200,000 g, Injection Moulding Machines Directly from the Manufacturer! Cedpow U N Ixjfx Akbogu As the manufacturer KraussMaffei, we offer you our certified and flexible stock machines: The hydromechanical two-platen clamping unit of the GXW machine sets new standards in terms of quality and productivity. With the sophisticated GuideX sliding shoe, forces are ideally absorbed and the service life of the moulds is extended. The innovative GearX locking system engages instantly and reliably. Powerful, user-friendly and value-retaining. TECHNICAL DATA: KM 650 / 2000 / 2000 GXW G06 (Order 38618339) CONTROL SYSTEM - MC 6 with 24'' TFT color screen with multitouch functions CLAMPING UNIT - Clamping force: 6500 kN - Max. mould opening force: 455 kN - Daylight opening (h x v): 1110 x 960 mm - Platen size (h x v): 1540 x 1440 mm - Mould installation height min. - max.: 1550 mm (without centre platen) - Opening stroke: 3200 mm - Max. mould opening distance: 1650 mm - Max. mould weight: 22,000 kg INJECTION UNIT 1 SP2000 - Screw diameter / type: 60 mm / thermoplastics - Effective L/D ratio: 23.3 - Injection pressure: 2420 bar - Shot volume: 792 cm³ - Shot weight at max. stroke for PS: 720 g - Injection speed: 140 mm/s - Injection throughput: 396 cm³/s - Screw drive speed: 285 rpm - Plasticizing throughput: 72.2 g/s - Nozzle contact force: 82 kN INJECTION UNIT 2 SP2000 - Screw diameter / type: 70 mm / thermoplastics - Effective L/D ratio: 20 - Injection pressure: 1877 bar - Shot volume: 1078 cm³ - Shot weight at max. stroke for PS: 981 g - Injection speed: 140 mm/s - Injection throughput: 539 cm³/s - Screw drive speed: 285 rpm - Plasticizing throughput: 98.3 g/s - Nozzle contact force: 82 kN ELECTRICAL PARAMETERS - Connected load: 341 kW - Power supply: 400 V / 50 Hz, 3 phases with neutral conductor WEIGHT & DIMENSIONS - Net weight: 43.5 t - L x W x H: 11.89 x 3.22 x 2.77 m ADDITIONAL EQUIPMENT - Wear-resistant plasticizing unit - BluePower full insulation for plasticizing cylinder - Open nozzle - BluePower ServoDrive - Pneumatic valve: 1-fold (BWAP), 1-fold (FWAP) - Pneumatic cascade valves: 6-fold (BWAP), 6-fold (FWAP) - Hydraulic core pull: 2-fold (BWAP), 2-fold (FWAP) - Mould heating: 96 zones (3.5 kW each) - Euromap interface for handling: E18 - Euromap central computer interfaces: E67, E77, E78, E63, E82.1 - Adaptive Process Control (APC+) - Graphic analysis package - Sliding table with turning unit, servo-driven - Vertical centre platen - Parallel clamping & opening during injection process with bar parallelism control between FWAP and centre platen or BWAP and centre platen - ColorForm interface signal interface for connecting an RPM unit - Electrical interface for HRS-Flexflow system - Electrical interface and hydraulic valves for "1-K dummy operation" - Interface for connecting a CoMo-Kistler Injection Basic System with good/bad part separation The machine is located at our plant in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your enquiry.

Condition: ready for operation (used), Year of construction: 2002, functionality: fully functional, machine/vehicle number: 424227, clamping force: 4,200 kN, screw diameter: 80 mm, injection pressure: 1,829 bar, injection weight: 1,304 g, opening stroke: 1,400 mm, TECHNICAL DETAILS Clamping force: 4,200 kN Platen size (H x W): 1,270 x 1,200 mm Tie bar spacing (H x W): 800 x 800 mm Minimum mold height: 380 mm Cjdpfx Aksy T Hwiebsgu Maximum mold height: 1,020 mm Max. opening stroke: 1,400 mm Screw diameter: 80 mm Injection volume: 1,433 cm³ Shot weight: 1,304 g (PS) Max. injection pressure: 1,829 bar Max. temperature: 375 °C MACHINE DETAILS Supply voltage: 400 V Phases: 3~ Frequency: 50 Hz Total current consumption: 237 A Fuse rating: 250 A Pump power: 75 kW Heating power: 36 kW Dimensions & Weight Dimensions (L x W x H): 7.06 x 2.33 x 2.51 m Machine weight: approx. 22,000 kg

Condition: good (used), Year of construction: 2006, operating hours: 65,000 h, clamping force: 2,000 kN, screw diameter: 55 mm, Hydraulic core pull 2x Hot Runner 4x Air valves Cgodpfx Akstqifnjbju

Condition: used, Year of construction: 1998, operating hours: 99,161 h, clamping force: 32,000 kN, screw diameter: 130 mm, injection weight: 8,100 g, total length: 4,900 mm, total height: 4,200 mm, overall weight: 230,000 kg, # Sales Description A high-performance injection molding machine from the German manufacturer KraussMaffei is available for sale. This is the KM 3200-19000 MC model, specifically designed for the production of large-sized plastic components and industrial series manufacturing. The machine offers very high clamping force and is particularly suitable for applications involving technical plastic parts or large-scale items. The machine features a clamping force of 32,000 kN, a screw diameter of 130 mm, and a maximum shot weight of 8,100 g. This allows for the efficient production of large parts with high material requirements. In addition, the system is equipped with extensive peripheral equipment, including a robot interface for KUKA KRC4, a S.I.S.E. IS’Tech sequential injection controller, GWK temperature control units, and a Motan Colormetric dosing and mixing system. A belt conveyor is also included in the package. Technical Data * Manufacturer: KraussMaffei * Model: KM 3200-19000 MC * Machine No.: IMM MC3F No.12 * Year of manufacture: 1998 * Operating hours: approx. 99,161 h Performance * Clamping force: 32,000 kN * Screw diameter: 130 mm * Max. shot weight: 8,100 g Dimensions and Weight Csdjyt H Dhjpfx Akbsgu * Machine weight: approx. 230,000 kg * Machine depth: approx. 4,900 mm * Machine height: approx. 4,200 mm The machine represents a robust and proven solution for industrial plastics processing and is especially suitable for manufacturers requiring large-format injection molding capacity. Further information, photos, or inspection appointments are available upon request.

Condition: like new (used), Year of construction: 2010, operating hours: 65,850 h, functionality: fully functional, machine/vehicle number: 61013689, clamping force: 2,500 kN, screw diameter: 50 mm, clearance between the columns: 630 mm, displacement volume: 432 cm³, injection pressure: 2,304 bar, injection weight: 393 g, Equipment: documentation/manual, As a dealer in injection moulding machines, we are offering the following well-maintained used injection moulding machine We also, of course, purchase well-maintained injection moulding machines manufactured from 2010 onwards We have been wholesalers of used injection moulding machines for over 25 years In light of recent developments – tax information and benefits for used machinery From 1 July 2025, used machinery will also be eligible for a special annual depreciation allowance of 30% for tax purposes. In addition to the lower price compared to a new machine, you can claim the same depreciation amounts as for a new machine Keyword: Growth booster (Section 7(2) EStG-E) Currently in stock and tested at our Hanover warehouse Manufacturer: Krauss Maffei Model: KM 250 1000 CX Control unit: MC5 Year of manufacture: 2010 Operating hours: 65,850 h Machine number: 61013689 Processed material: PE and PP – thermoplastics Extras - 2 x core pull (movable WAP, fixed WAP) - Pneumatic valve 1 on FWAP - Pressure accumulator for increased injection capacity - Fast SK removal CX Midrange - Ejection of cooled nozzle plug - Start handling during mould movement - Start-up sequence - Cycle time analysis - External USB keyboard - Graphical analysis – maintenance instructions - Electronic coding of injection unit - Pneumatic valve on BWAP blow-out - 12 temperature control points - Potential-free contact BDE - Process monitoring - Cycle storage - Trend graph - Target/Actual graph - PV control - Active back pressure control - From first owner - Origin: Germany Regular maintenance carried out by the manufacturer and previous owner Clamping unit Clamping force: 2500 kN / 250 tonnes. Cgjdpfxsxqhuuo Akbou Column spacing: 630 x 630 mm Platen dimensions: 995 x 1050 mm Opening width: 820 mm Mould height: 330 mm min. Opening width max. 1150 mm Ejector stroke: 200 mm Ejector force: 57 kN max/26.3 kg Injection unit Screw diameter: 50 mm Injection volume: 432 cc Shot weight: 393 g/PS Injection pressure: 2304 bar Electrical Pump: 45 kW Heating: 5 zones, 18.7 kW Weight: 13,900 kg. Dimensions: 5.7 x 2.3 x 2.3 m. Complete documentation, manual and software Available immediately from our warehouse in Hanover, Germany, or free delivery subject to reimbursement of freight costs The machine is offered with a functional test certificate The machine is our sole property The machine in question is available immediately from our warehouse in Hanover, is offered in a functionally tested condition and can be viewed whilst powered up. Information about the machines we offer and our company - We only sell machines purchased from current production from our warehouse in Hanover - All machines on offer are inspected and tested prior to dismantling - We do NOT sell goods from insolvency estates - We are NOT a broker dealing in third-party property. - All machines on offer come from successful companies for whom maintenance and upkeep are a matter of course - All machines on offer can be viewed at our warehouse

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, Here we offer a very well maintained constantly serviced injection molding machine complete maintenance by manufacturer until current Injection molding machine Krauss-Maffei KM 65-160 C2 Injection molding machine: Manufacturer / Type: Krauss-Maffei KM65 160 C2 Serial No.: 61007063 Year of manufacture: 2005 Control system: MC4 complete annual maintenance by the manufacturer clamping unit: clamping force: 650kN /65 tons tie bar distance: 405 x 405mm mold installation height min.: 250mm platen distance max.: 750mm Clamping platens standard: 610 x 610mm ejector stroke: 150mm core pull: 1 x pcs. Injection unit Injection unit size / cylinder ø: 160 / cylinder ø25mm and cylinder ø18mm Shot weight max (ø25): 47g/PS Injection flow: 63cm³/sec Spec. injection pressure: max. 2500 bar Handling interface: Euromap 12 Inking interface: Yes Dimensions & weights: Weight with control cabinet: 3.8 t Cedpfsh Dp R Ejx Akbogu Length: 3800mm Width (machine only): 1050mm Height: 1890mm Oil filling: 270 L Location: Hannover / Lower Saxony The machine is very well maintained and can be inspected under power. Peripherals that may be pictured are NOT part of the offer! The machine is available now in our warehouse free loaded on truck of the buyer or free to the door against freight reimbursement

Condition: like new (used), Year of construction: 2008, operating hours: 6,200 h, functionality: fully functional, clamping force: 4,200 kN, screw diameter: 75 mm, Krauss-Maffei KM 420-2000 CX Krauss-Maffei injection molding machine, 420 tons of clamping force. Only 6,000 hours of automatic operation. Year of manufacture 2008. MC5 control. Screw diameter 75 mm. Extras: 8 hot runner zones. 2 cores on fixed platen, 2 cores on moving platen. 1 pneumatic valve on moving platen. The injection molding machine is delivered reconditioned by UK Transitus' expert technical team. We can offer commissioning at our clients' facilities, ensuring operation upon completion of the installation. Technical Details 75mm screw Injection pressure: 1635 bar Cgodpfx Aswq D Efjkbsu Shot volume: 1237 cm3 Shot weight: 1126 g Maximum distance between plates: 1400 mm Minimum mold thickness: 380 mm Opening stroke: 1020 mm Distance between columns: 900 x 800 mm Plate dimensions: 1270 x 1230 mm 75mm screw Clamping force: 4200 kN Year of manufacture: 2008 Working hours: 6282

Condition: used, Year of construction: 2004, operating hours: 76,000 h, total height: 2,480 mm, total width: 2,330 mm, total length: 9,830 mm, screw diameter: 70 mm, clamping force: 4,200 kN, displacement volume: 1,047 cm³, 2. Unit 55 with ø 22 Injection pressure: 1674 bar Volume: 30cm³Distance between injection unit 1 and 2: 300 mm (piggy / Multinject) clamping force: 4200 kN distance between tie-bars h x v: 800 x 800 mm size of mould plates h x v: 1270 x 1200 mm min. mould height: 380 mm max. open daylight: 1400 mm opening stroke: 1020 mm screw diameter: 70 mm swept volume: 1047 ccm injection pressure: 1778 bar equipment included screen text german core pulling hydraulically 6x Codpjyv E Ewsfx Akbjgu Machine without Handling machine without material hopper Anti vibration mounts mould heating 16x Injection moulding machine for two components measures of machine l x w x h: 9.83m x 2.33m x 2.48m total weight: 23090KG

Condition: ready for operation (used), Year of construction: 2005, operating hours: 59,000 h, clamping force: 4,200 kN, screw diameter: 60 mm, displacement volume: 769 cm³, injection pressure: 2,200 bar, total length: 6,830 mm, total width: 2,330 mm, total height: 2,480 mm, overall weight: 23,090 kg, Clamping force: 4200 kN Tie bar spacing (H x V): 800 x 800 mm Platen size (H x V): 1270 x 1200 mm Min. installation height: 580 mm Max. platen distance: 1300 mm Opening stroke: 720 mm Screw diameter: 60 mm Shot volume: 769 ccm Injection pressure: 2200 bar Equipment Display language: German Hydraulic core pull 4x Machine without handling Machine without material hopper Levelling elements Mould heating 12x Cgedoyv E Daepfx Akbju Machine dimensions (LxWxH): 6.83m x 2.33m x 2.48m Total weight: 23090 kg

Condition: ready for operation (used), Year of construction: 2010, operating hours: 54,872 h, functionality: fully functional, clamping force: 2,500 kN, screw diameter: 55 mm, displacement volume: 570 cm³, injection pressure: 2,387 bar, total length: 6,500 mm, total width: 2,200 mm, total height: 2,300 mm, overall weight: 15,000 kg, clamping force: 2500 kN Cgsdpfxoyv Elwe Akbeu distance between tie-bars h x v: 630 x 630 mm size of mould plates h x v: 995 x 1050 mm min. mould height: 330 mm max. open daylight: 1150 mm opening stroke: 820 mm screw diameter: 55 mm swept volume: 570 ccm injection pressure: 2387 bar measures of machine l x w x h: 6.5m x 2.2m x 2.3m total weight: 15000KG

Condition: good (used), Year of construction: 2004, clamping force: 1,250 kN, screw diameter: 45 mm, clearance between the columns: 470 mm, displacement volume: 275 cm³, injection pressure: 1,878 bar, injection weight: 250 g, mold height (min.): 300 mm, Krauss Maffei 125-520 C2 General Information Model: 125-520 C2 Year of manufacture: 2004 Control system: MC4 Machine weight: 6,000 kg Dimensions (L × W × H): 4.5 × 1.5 × 2.2 m Clamping Unit Clamping force: 125 t Cgjdoyxl Dlepfx Akbeu Clamping system: 125 / … Platen size: 745 × 770 mm Tie bar spacing: 470 × 470 mm Opening stroke: 600 mm Max. platen distance: 900 mm Mold height: 300 mm Ejector force: 22 kN Ejector stroke: 150 mm Injection Unit Injection unit: … / 520 Screw diameter: 45 mm Screw L/D ratio: 20 Shot volume: 275 ccm Shot weight: 250 g Specific injection pressure: 1,878 bar

Condition: good (used), Year of construction: 1999, clamping force: 2,000 kN, Manufacturer: KraussMaffei Kunststofftechnik München Model: KM 200-700 C2 Machine No.: 174406 International size designation: 700 C2 / 200 Year of manufacture: 1999 Clamping force: 2000 kN Cgsdpfjytiqwjx Akbju Clamping force: 200 t Injection unit size: 700 Machine weight: 8,800 kg Location: Freiburg

Condition: good (used), Year of construction: 2002, clamping force: 1,100 kN, Manufacturer: KraussMaffei Kunststofftechnik München Model: KM 110-390 C2 Machine No.: 1141268 Order Number: 646749/1 Year of manufacture: 2002 Clamping force: 1100 kN Clamping force: 110 t International size designation: 390 C2 / 110 Injection unit size: 390 Operating voltage: 400 V Phases: 3 Frequency: 50 Hz Total current: 164 A Main fuse: 200 A Cgjdpfx Akjytipaebeu Motor current: 37 A Machine weight: 5800 kg Location: Freiburg

Condition: good (used), Year of construction: 1999, clamping force: 650 kN, Manufacturer: KraussMaffei Kunststofftechnik Munich Model: KM 65-160 C2 Clamping force: 650 kN Machine No.: 641070 Cgsdpfjytik Rex Akbeu Order number: 643883/1 Year of manufacture: 1999 International size designation: 160 C2 / 65 Operating voltage: 400 V Phases: 3 Frequency: 50 Hz Total current: 153 A Main fuse: 160 A Max. motor current: 30 A Machine weight: 3,200 kg Location: Freiburg