Used Bollegraaf Baler 100 T Press Force, With 10-Fold Cross Tying System for sale (105,658)

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. Ijdpezdn H Rsfx Aqusic New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2025, volume flow: 410 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Iiedezdnxgjpfx Aquec Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Isdpfozbxwiex Aquoic Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Iijdpjy S Rqwofx Aquec Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: good (used), Year of construction: 2019, Professional packaging machine from a renowned European manufacturer for adhesive tape widths up to 50 mm. Maximum carton dimensions approximately: width 525 mm x height 505 mm; length unlimited. This is a robust machine designed for the highest demands. Iiedpfx Ajyywazsquec - Double-sided sealing of cartons top and bottom with adhesive tape. - Transport speed up to approx. 20 m/min. - Various carton formats can be adjusted continuously in height and width via a quick-adjustment system (no hand crank required). - Working height adjustable from 635 to 950 mm. Special features/options: - Delivery includes an infeed conveyor approx. 1 m in length and an outfeed conveyor approx. 1 m in length. The outfeed conveyor is equipped with a stop plate, which can be removed if needed. Both roller conveyors are adjustable in height and inclination. - The machine has an adjustable sealing device for carton flaps at the infeed. - Machine speed is adjustable via a potentiometer. The machine can be demonstrated under power.

Condition: like new (used), Year of construction: 2020, load capacity: 1,000 kg, lifting height: 1,880 mm, construction height: 1,560 mm, operating hours: 3,102 h, fuel type: electric, mast type: duplex, Manufacturer & model: TOYOTA OSE 100 Mast: 2W1880 ID: 25110.8747 Category: Used Mast type: 2W Iedpozaf H Iefx Aqujic Lowered height: 1560 mm Lifting height: 1880 mm Capacity: 1000 kg Platform height: 1200 mm Picking height: 2800 mm Initial lift: Yes Cabin width: 800 mm Year: 2020 Operating hours: 3102 hours Battery capacity: 24V / 620Ah Options: with SAFETY gates !!

Condition: excellent (used), For sale: Professional automatic Vickers hardness tester Mitutoyo HV-100, made in Japan, in excellent technical and visual condition. The device is equipped with the AUTOVICK automatic measurement system and the Mitutoyo Vision Unit, enabling fast, repeatable and fully automatic hardness measurements without operator subjectivity. Intended for measurement laboratories, quality control departments, manufacturing plants, automotive, aerospace, and toolmaking sectors. —— Isdpfxeyc H I Se Aqujic Key information • Measurement method: Vickers (HV) • Model: HV-100 (series HV-100B / HV-100C / 100D) • Load range: up to 100 kgf • Automatic AUTOVICK system • Integrated Mitutoyo Vision Unit • Automatic impression recognition and HV calculation • Made in Japan • Power supply: 230 V • Stable, heavy-duty laboratory construction —— Technical condition • Device operational and complete • Very good visual condition • Regularly used in an industrial environment • Last technical inspection: 2020 • Ready for immediate operation after connection —— Included in the set • Mitutoyo HV-100 hardness tester • Vision Unit (measuring camera) • AUTOVICK automatic system • Set of weights • Original accessories and holders • Transport cases with equipment • Original Mitutoyo documentation and manuals • Weight: 65 kg

Condition: ready for operation (used), Year of construction: 2025, An integrated packaging system Soco consisting of a carton erector and a carton sealer is available. 1) Bottom flap folder Soco F-100P, min. carton width: 320mm, max. carton width: 520mm, max. carton length: 900mm, machine dimensions X/Y: approx. 750mm/1150mm. 2) Carton sealing machine Soco T-402 5-5-7, carton length range: 200mm-750mm, carton width range: 120mm-460mm, carton height range: 95mm-470mm, sealing capacity: 18/min, max. adhesive tape roll diameter: 385mm, weight: approx. 200kg. Including safety guarding, roller conveyor and transfer unit. The system is as new and has only been in operation since January 2026. Documentation available. An on-site inspection is possible. Iodpey Hk Tnsfx Aquoic

Condition: new, Year of construction: 2026, MOULDER INFEED IF-100 MAX FEED SPEED 100M/MIN MAX LENGTH 6100MM MIN LENGTH 1500MM Iijdpfx Aey Hb U Njqusc FLAT CHAIN CROSS FEED WITH 5 CHAINS INVERTER DRIVE ACCELERATOR 5KW MAX WIDTH 250MM MIN WIDTH 50MM MAX THICKNESS 100MM MINIMUM THICKNESS 12MM 4X FEED ROLLERS 180MM MOULDER OUTFEED OF-100 DROP LEAF OUTFEED CAPABLE OF HANDLING ALL SIZES AS PER IF-100 INFEED CROSS FEED TABLE WITH 7X BELTS SUITABLE FOR UP TO 100M/MIN AVAILABLE EX STOCK PRICE INCLUDES INFEED AND OUTFEED POSSIBLE TO OFFER SUITABLE MOULDER AS NEEDED, WEINIG OR LEADERMAC !!!

Condition: good (used), Schmedt PraForm HHS 2100 book press with joint forming Perfect condition, purchased from a warehouse, used as a backup. Book press with groove burner. Iisdpfjwud Tkjx Aqujc Manufactured by Schmedt, Germany. Technical data: max format: 400x 520x 100 mm Weight 250 kg Power supply 380 V + compressed air.

Condition: as good as new (ex-display), Year of construction: 2026, functionality: fully functional, The BTS-MF100 is the ideal waste baler for compacting your loose cardboard and plastic film waste into a bale of up to 100 kg. It is equipped with automatic bale cycle, hour counter and also strap eject system. The baling press impresses with its ease of use, safe operation and its large filling volume. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 6 Ton Bale weight: up to 100 kg (material depending) Bale size: 850 H (var.) x 980 W x 800 D mm Machine size: 2399 H x 1440 W x 1014 D mm Machine weight: 632 kg Transport height: 2399 / 1876 mm (on request) Loading aperture: 980 W x 480 H mm Cycle times: 28 seconds Motor: 1.5 kW 13 Amp Power supply: 220 - 240 V (1 phase) Noise level: 68 dB Auto control panel with bale full light and E-stop with locking key Hour counter Strap eject for easy removal of bales Retainer for reducing the material spring back Reel holder for 4 rolls of strapping A quality product “Made in Europe” Suitable for compacting Cardboard Plastic film and foils Clothes Iodovaimuopfx Aqueic Light valuable materials Optional extras Machine colour RAL Strapping rolls Power supply 380 - 400 V (3 phase) Waste Baler, Waste Compactor, Cardboard Baler, Film Baler, Foil Baler, Packaging Plastic Film Foil, Bailer, Baling Press, Garbage Press, Trash Compactor, Baling Compactor, Paper Press, Waste Paper Press, Cardboard Press, Cardboard Compactor, Foil Press, Paper Baling Press, Waste Baler, Residual Waste Compactor

Condition: excellent (used), Year of construction: 1990, functionality: fully functional, pressing force: 100 t, stroke length: 500 mm, operating speed: 200 mm/s, reverse speed: 200 mm/s, table width: 750 mm, table length: 560 mm, ram plate width: 530 mm, ram plate length: 400 mm, total length: 1,900 mm, total width: 1,200 mm, total height: 3,200 mm, overall weight: 5,040 kg, Equipment: documentation/manual, Hydraulic press PYE 100 S1M with ejector. Manufacturer: Werkzeugmachinen GmbH Zeulenroda (Germany), year 1990. Specifications: Maximum pressing force 100 t. Operating pressure 16 MPa. Maximum ejector force 40 t. Ejector piston stroke 200 mm. Upper table 530x400 mm. Lower table 750x560 mm. Clear opening 800 mm. Cylinder stroke 500 mm. Downward speed 200 mm/s. Upward speed 200 mm/s. Power requirement 17 kW. Weight 5040 kg. Height 3200 mm, length 1900 mm, width 1200 mm. Iijdpfx Aqsygtzyouec

Condition: used, mileage: 388,200 km, power: 302 kW (410.61 HP), first registration: 03/2012, fuel type: diesel, tire size: 425/65 R 22.5, axle configuration: 8x4, wheelbase: 6,710 mm, fuel: diesel, driver cabin: day cab, gearing type: automatic, emission class: euro5, suspension: air, total length: 9,240 mm, total width: 2,510 mm, Year of construction: 2012, Equipment: ABS, AdBlue, air conditioning, central locking, crane, cruise control, electric window regulation, trailer coupling, = Additional Options and Accessories = - 8x4 axle configuration - Digital tachograph - Lifting axle - Air suspension - Hub reduction - PTO (power take-off) - Radio/CD player - Sun visor - Towing hitch = Further Information = Technical Details Number of cylinders: 6 Engine displacement: 12,882 cc Axle Configuration Front axle: Tyre size: 425/65 R 22.5; Steered; Left tyre tread: 45%; Right tyre tread: 45%; Suspension: air suspension Rear axle 1: Tyre size: 315/80 R 22.5; Twin tyres; Inner left tread: 60%; Outer left tread: 60%; Inner right tread: 60%; Outer right tread: 60% Rear axle 2: Tyre size: 315/80 R 22.5; Twin tyres; Inner left tread: 25%; Outer left tread: 25%; Inner right tread: 25%; Outer right tread: 25% Rear axle 3: Tyre size: 425/65 R 22.5; Steered; Left tyre tread: 50%; Right tyre tread: 50%; Suspension: air suspension Weights Unladen weight: 10,930 kg Payload: 28,070 kg Gross vehicle weight: 39,000 kg Functional Iisdpfx Aqozb Higsusc Crane: Palfinger / Epsilon Q170295TR, year of manufacture 2012, mounted behind cab Condition Damages: none

Condition: new, RHTC 100 TON M/H-M/C-2 Hydraulic Press Iiedpfx Asxwk E Asquec Model 100 TON M/H-M/C-2 Year 2025 Condition New Stock Number 2796 Working Width 1000 mm Stroke 380 mm Max Capacity 100ton

Condition: new, pressure: 100motor: 11daylight: 500stroke lenght (max.): 400Tappet adjustment: 790 x 600table height: Fußboden zu Tischplatte Oberkannte - 850messurements (LxWxH): 1.300 x 2.000 x 2.750weight approx.: 5.500oil filling: 200Type: Hydraulic C-Frame PressCapacity: 100 tons at 230 barControl / Key Switch Modes:Setup Mode – Manual operation without light sensor Automatic Mode – Full speed with integrated light sensor Hydraulic System:Main Cylinder: Ø 230 mm Auxiliary Cylinders: 2 pcs, Ø 50 x 30 mm Auxiliary Guides: 2 pcs, Ø 50 mm Motor: 11 kW / 15 HP Pump: 16 cc, 23 L/min – Helical gear pump Speed:Approach: 110 mm/sec Iijdpfx Ajwrkctequsc Return: 200 mm/sec Pressure phase: 9 mm/sec Machine Dimensions:Daylight Opening: 500 mm Stroke Length: 400 mm Ram Plate: 790 x 600 mm (with T-slots) Table Plate: 790 x 600 mm (with T-slots) Table Height: 850 mm (from floor to top of table) Hydraulic Equipment:REXROTH hydraulic control block & components Pressure adjustable via PLC (20 – 100 tons) Speed adjustable via PLC Air oil cooler Pre-fill valve Pressure hold valve Control System:Siemens S7-1200 PLC Main control cabinet Safety PLC (SICK) Light curtains (SICK – 700 mm) Linear encoder for stroke adjustment 10” PLC touchscreen – BEIJER (German & English) Movable two-hand control unit Ethernet connection for remote support Visual and acoustic fault alarms Dual work area lighting In full compliance with EN 693 machine safety regulations Side safety doors (outward opening) Hydraulic proportional valves Dual-channel safety control User manual & parts list (German) Oil Volume: 220 L (Tank capacity: 250 L)Total Weight: approx. 5,500 kgOverall Dimensions: 1300 x 2000 x 2750 mmColor: RAL 7035 Light Grey & RAL 7016 Anthracite Grey Besichtigung unter Strom bei uns in Böheimkirchen 3071 (Neustiftgasse 34) möglich.

Condition: used, functionality: fully functional, Year of construction: 2017, operating hours: 3,400 h, load capacity: 1,800 kg, lifting height: 5,070 mm, free lift: 1,670 mm, load center: 500 mm, fuel type: electric, mast type: triplex, construction height: 2,260 mm, battery capacity: 625 Ah, remaining battery capacity: 100 %, battery voltage: 48 V, battery weight: 892 kg, fork carriage width: 980 mm, fork length: 1,200 mm, tire condition: 90 %, front tire type: superelastic tires (non-marking), rear tire type: superelastic tires (non-marking), drive type: Elektro, Equipment: UVV, lighting, pallet forks, sideshift, Electric 3-wheel forklift Load center: 500 ISO class: ISO class 2 = 1,000 - 2,500 kg Mast type: Triplex Condition: Refurbished, no warranty Technical condition: very good Front tire type: Non-marking Front tire condition: 80 - 100% Rear tire type: Non-marking Rear tire condition: 80 - 100% Battery voltage: 48V Battery capacity: 625Ah Battery manufacturer: Tested (C5 test) with 100% Battery type: PzS Battery year of manufacture: 2025 Battery condition: 80 - 100% Description: Overhauled, maintained and inspected in accordance with FEM 4.004 (UVV). Completely repaired, serviced and checked. Ijdpfxoytkc Uj Aquoic Side shifter, third valve, rear working light, front working light, overhead guard, front windscreen, safety light, joystick,

Year of construction: 1991, condition: good (used), Carton sealer, packaging machine, carton closing machine, carton sealing machine, sealing tape machine, adhesive tape machine Iodpfjlry S Aox Aqujic -Manufacturer: Soco System, Carton Sealer Type T-10 -Carton width: max. 530 mm -Dimensions: see photos -Overall dimensions: 980/930/H1680 mm -Weight: 135 kg

Condition: good (used), Year of construction: 2004, machine/vehicle number: 300 584, functionality: fully functional, power: 2 kW (2.72 HP), input voltage: 400 V, input current: 85 A, type of input current: three-phase, overall weight: 8,000 kg, year of last overhaul: 2016, We are selling a complete shredding line including: - Artech RS75 shredder - Pusher / compactor - Electrical control cabinet - Overband magnet - Sampler Iijdpexrtwwsfx Aquec The loading conveyor and the discharge conveyor after shredding are not included in the sale.

Condition: reconditioned (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, overall weight: 9,500 kg, year of last overhaul: 2025, filling opening width: 420 mm, filling opening length: 1,250 mm, Technical data packing press / can press / metal sheet press: Iijdpfozbxvljx Aquec Manufacturer unoTech GmbH Type UPAXX 70 Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Connected load 40 kW Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: The packing press has been fully overhauled in our workshop. The press is in very good condition; please see the demonstration video following the overhaul. The machine sustained transport damage whilst being moved. The control cabinet was damaged and slightly dented by a forklift truck, and the main switch (on/off switch) was damaged. These damages are reflected in the significantly reduced sale price and must be repaired by the buyer at their own expense. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2026, condition: new, functionality: fully functional, • A vertical guillotine shear with a 3 mm or 6 mm steel cutting capacity on a 3 m width, with a motorized back gauge, an optical system for contour cutting, and an optional pneumatic sheet support. • A 50 or 100 T press brake with a 3 m distance between uprights, with 3 digitized axes (X, the back gauge, and synchronization of the left Y1 and right Y2 cylinders). A CYBELEC touch-screen CNC control with digital or graphical programming. Features: With minimal floor space in the workshop, you have the equivalent of 2 high-end conventional machines: • A vertical guillotine shear equipped with a motorized back gauge (700 mm length), an optical system for contour cutting, proportional clamping relative to the cutting force, 2 reversible 4-sided blades, and an optional pneumatic sheet support. • A press brake equipped with a motorized back gauge (700 mm length) and fully electronic angle management with 2 digital rulers (synchronization of the left Y1 and right Y2 cylinders with force management), allowing bending either in a single stroke or in the air with a positioning accuracy of 0.04 mm. - Distance between uprights = 3200 mm - Unlimited bending capability, as there is no interference with the gooseneck! - Direct angle programming + graphical programming with automatic calculation of the developed length and 2D bending simulation. - Automatic pressure control in real time. - A complete set of tooling with a 9-V die + gooseneck punches + adjustable punch holders. - A 2-year warranty. Available in several versions: - Cutting capacities: 3 or 6 mm steel - Cutting lengths: 1250 / 2040 / 3040 mm - Bending pressure: 50 and 100 T - Bending lengths: 1400 / 2200 / 3200 mm - Cybelec graphical CNC control, 3 axes. More than 1000 installations in Europe. Inquire now! With the COMBI and its 3 digitized axes X, Y1, Y2, you really have the equivalent of 2 excellent machines, with the added benefit of technology typically intended for industrial applications (Y1 Y2 synchronization). Since 2004, JC COLOMBO has been distributing the COMBI combined shear and press brake. With ideal capabilities for locksmithing and metalworking activities (3040 x 6 mm shear and 3200 x 75 T bending), the COMBI allows all companies that do not have space for 2 conventional machines to equip themselves and become fully self-sufficient and much more responsive to complete projects. Workshops with 100 m² and 2 employees have opted for the COMBI! A 50 T version has also been specifically designed for the production of cladding for aluminum joinery companies. Furthermore, with equipment such as the automatic sheet support for the shear, the Y1 Y2 cylinder synchronization, and the direct angle setting program, the customer really has the equivalent of 2 excellent industrial-grade machines at a lower cost. Iiedpfx Aozcyx Doquec To date, more than 600 professionals use the COMBI in France.

Year of construction: 2025, condition: new, Hydraulic C-frame press (punch press) Year of manufacture: 2025 Capacity: 100 tons at 230 bar Control / key switch: 1. Manual setup mode without light sensor 2. Automatic (at full speed) with light sensor Main cylinder: Ø 230 mm Auxiliary cylinders: 2 x Ø 50 x 30 mm Auxiliary guide: 2 x Ø 50 mm Motor: 11 kW – 15 hp Pump: 16 cc – 23 liters / ASC – Helical gear pump Speed: Forward 110 mm/sec – Return 200 mm/sec Pressure phase: 9 mm/sec Installation height: 500 mm Stroke length: 400 mm. Push plate: 750 x 600 mm. – with T-slots Table top: 750 x 600 mm. – with T-slots Table height: 850 mm. (Floor to table top edge) ----- Hydraulic accessories: Hydraulic control block & accessories: REXROTH Pressure adjustment via PLC. (20 – 100 tons) Iodpfowag Riex Aqujic Speed adjustable via PLC. Air cooler Feed valve NG.63 Control accessories: Siemens S7-1200 Blsbjftg Sgsmmvyhwof Main control box Foldable control panel With side safety door (doors can be moved backwards) SICK 750 + 150 mm light sensors. Ruler for adjusting the stroke length 7" PLC screen – Siemens Movable two-hand control Alarm indicator for faults (light & sound) ----- • The press complies with the EN693 Machinery Directive • Hydraulic two-way valves • Dual-channel fused control system • Safety PLC – SICK • Operating instructions & parts list (German) • Warranty: 24 months ----- Oil capacity: 190 liters (Tank volume: 205 liters) Total weight: approx. 5,500 kg. Overall dimensions: 1300 x 2000 x 2750 mm. Delivery time: 2 - 3 weeks from stock. Paint finish: Light gray & dark gray The machine is available immediately in 2 - 3 weeks. Freight: approx. €2,000 from Konya to Germany

Condition: used, Year of construction: 1995, functionality: limited functionality, cutting force: 800 t, empty load weight: 190,000 kg, type of input current: three-phase, Arnold HS850 Scrap & Metal Presse Die Maschine befindet sich derzeit in transportbereitem Zustand. master cylinder cylinder force: 850 t press: 0.08m/s hold-down cylinder cylinder force: 100t / per cylinder feed cylinder: cylinder force:100t cover cylinder: cylinder force:100t main dimensions total length:16175mm total width:5200 total height: 6420 mm Dimensions: Passage width at the scissor stand: 800mm passage height at the scissor stand: 800mm total height: 6000mm weights: scissor stand with cutter bar: 60 ton feed device approx: 85 ton total weight: about 170 tons required amount of oil: 5200 liters connection value of the machine: 220kw Iiodpfx Aqoh T Dctousc If you need more information. We are here to help! Please contact us using the contact form or give us a call Your ad has been automatically translated. Translation errors are possible.

Condition: new, Year of construction: 2021, pressing force: 10 t, Single-column press with 10 T capacity, suitable for continuous shift operation, with these basic data: a) Traversing speed 0 - 10 mm/sec. downwards, b) Opening speed up to 25 mm/sec c) Starting press speed 10 mm/sec, adjustable from 0 to 10 mm/sec. d) Table size 600x300 mm e) Ram size 300x300 mm, with T-slots and central cylinder clamping Iiedpfxohma Smo Aquoc f) Overall size approx. 1100x600x1850 mm g) Oil temperature display on oil tank h) Pressure setting from 0.5 T to 10 T (adjustable via rotary control) i) Cable remote control for downward/upward movement j) Machine body powder coated, or double painted k) Control cabinet supply cable from above with 3000 mm cable and 16 ampere plug l) Assembly, commissioning, instruction at extra charge Type of construction Press design Single-column press Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Max. pressing force (at 250 bar) 100 kN Free ripping force max. 10 kN Pressure build-up time Closed tool Steel on steel Max. 2 sec. Dimensions Max. Opening width 800 mm Stroke and min. opening 500/300 mm Table height above floor 850 mm Height above floor (headroom) approx. 2850 mm Hall height min. 3,500 mm Parallel deviation at 20°C #ERROR! mm Deflection Determined at max. clamping force with 70% occupancy < = 0.1 mm/m Weight Total weight of the press without operating materials approx. 1.6 to Speeds Fast closing with 10 mm sec. Press speed 10 - 0 mm sec. Sound pressure Sound pressure level, measured at 1.5 m height at the control panel according to DIN 45635-T16-KL3 max. 78 db(A) Hydraulics Number of pressing cylinders 1 pc. Operating pressure max. 250 bar Pressing pressure build-up time . 2 sec. Pressure accuracy during pressing stroke #ERROR! bar Main pump Gear pump approx. 6 L/min Oil volume approx. HLP 46 MW 80 litres Ambient temperature max. 40 °C Oil temperature max. 55 °C Flow temperature °C Electrical system Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Hydraulic connection Main motor 2.2 kW Total connection Approx. 3 kW

Condition: used, Year of construction: 2002, Italpresse BG/660 Molding press / Heated platen press – 660 t pressing force Manufacturer: Italpresse Model: BG/660 Year of manufacture: 2002 Iijdpfey Ufqdex Aquoc Condition: Used, operational Technical data * Pressing force: 660 t * Press platen size: 1,900 x 1,600 mm * Heating power: 31 kW * Connected power: 108 kW * Operating voltage: 400 V * Control voltage: 220 V * Frequency: 50 Hz * Phases: 3 + N + PE * Rated current: 160 A * Weight: approx. 28,000 kg * Design: Bottom platen heated platen press / Molding press Robust hydraulic molding press from Italpresse for the production of molded parts and glued wood components. The machine has heated press platens and a pressing force of 660 tons. Ideal for applications in the furniture, wood, and molding industries. The press is in used condition. Inspection possible by appointment. Documentation available.

Condition: used, Year of construction: 2012, Overview  This complete brewhouse was manufactured in 2012 and enables the production of 1,000-liter brews. The system works with steam and includes brewing, fermentation and storage tanks. It is immediately available and is currently installed and ready for operation in the production facility. The seller confirms that the system has worked perfectly until recently. The boilers have a copper coating, while the rest of the system is made of stainless steel. Details Wort yield: 1,000 liters per brew Heating system: Steam Current status: Installed and ready for operation Availability: Immediately Scope of delivery  Brewhouse | Mini Brewery System | CI T 10 | 2012 2 kettles (mash tun above the whirlpool as one unit + separate boiling kettle) Steam boiler | Mini Brewery System | - | 2012 (electric) Plate heat exchanger Hot water tank | 1,500 L Reverse osmosis system | ALFA | compact model | - Capacity: 150-200 L/h 4x Isobaric fermenter | Mini Brewery System | 1,000L | 2012 4x Horizontal isobaric maturation tank | DuoTank | 500 L | 2018 Cooling jacket & bag system for optimum beer preservation Iiodpev Da Dljfx Aqujc