Used Grit Univ. Radii Metal Belt Grinding Machine for sale (71,705)

Condition: used, Cylindrical Grinding Machine: Schaudt Model: RFH 500 Condition: used Centre height: 100 mm Centre distance: 500 mm Spindle speeds: 2225 / 2500 / 2825 rpm Grinding wheel diameter min./max.: 200 - 300 mm Weight, approx.: 1900 kg Equipment: - Manual & automatic operation - Coolant system - Machine lamp - Emergency stop button Kodpfxoy R Dlfe Ah Esdt - Machine leveling feet

Condition: used, grinding diameter 350 mm grinding length 1500 mm centre height 175 mm weight of the machine ca. 3 t High-End Kellenberger 1500U Ideal for spindle producer or overhauler Kdjdpfx Aot Ii Rreh Eot -BEMA Internal grinding device with separate, cooled motor. Grinding spindle and internal grinding spindle motor electrically interlocked! Internal grinding spindle can only be switched on when it is in position. A quantum leap in safety -Infinitely variable grinding spindle speed 1000-1500 rpm -Infinitely variable internal grinding spindle speed 0-100%. -Digital display of grinding spindle speeds -Swivelling angle display top table -swivel angle display grinding headstock -Marposs gaper sensor for external grinding only -fluid gating sensor Marposs internal grinding -Center height up to 250mm possible Machine is already delivered. Identical machine can be built with additional with additional options. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, Year of construction: 2022, Plus freight 4,000.00 € and installation and commissioning 5,000.00 € Grinding system B Sand 5 with partial lathe Working principle The panel is placed on the infeed table. It goes into the partial lathe and centered. It is ground in the grinding system, through and back. The panel is turned in the partial lathe. It is ground on the other side in the grinding system. Then there are two options: either the panel goes onto the outfeed table and unloaded or it comes back onto the infeed table and is unloaded there (the second option extends the working time). Grinding system equipment 1 upper grinding lamella roller suitable for surfaces. Power 3 kW; D 420 mm; L 1300 mm. Cross brush suitable for grinding the cross fibers. D 420 mm; L 300 mm. Power 1.1 kW. Cross brush suitable for grinding the cross fibers. D 420 mm; L 300 mm. Power 1.1 kW. 3 upper sanding discs for perfectly trimming the longitudinal and transverse wood fibers. Power 1.5 kW each; D 400 mm. Disc brush for beveling edges. The unit functions as a deep brush. After detecting the panel edges, it will follow the door edges. Power 0.75 kW; D 250 mm. Machine features: -The unique sanding system of this machine guarantees perfect wood sanding and/or intermediate sanding of the panels. -All tools are controlled by frequency converters. -All brushes are equipped with quick-release sanding strips without replacing the hub. -The discs are equipped with air bladders to optimize cleaning and service life. -Sanding discs are equipped with a Velcro fastening system. -The feed and rotation speed are PLC-controlled to prevent edge breakage. -High-quality sanding on 4 sides thanks to the system's constant removal rate. -Automatic and rapid unit changeover. - Constant throughput height, PLC and industrial software enable interlinking in a surface line. - Continuously variable speed of the discs, brushes and feed thanks to the fully equipped frequency converter. - Right/left rotation of the discs and brushes with different abrasive grits. - Individually driven feed of the discs, rollers and belts. - Additional adjustment of the brushes and discs to balance the use of the abrasive and to allow for changing the grinding pressure on the surfaces. - Strong support bed made of tubular steel guarantees the best rigidity, stability and flatness. - Planed upper support bed to ensure the best parallelism of the working surface for the grinding discs. - All unit carriages are designed with linear recirculating ball bearing guides, thus high load capacity and high precision. - Motorized feed belt controlled by a frequency converter, 0.55 kW. Machine doors equipped with safety devices. - Machine doors equipped with windows to observe the workpieces during operation. - Under the units, there are 80 mm rubber-coated pressure rollers to hold the workpieces in place during processing. · Low follow-up costs thanks to individual blade replacement. · Low running noise thanks to the enclosed system housing. · All units have suction housings with their respective suction supports. Cover plate with suction nozzle. · Completely encapsulated machine housing for a clean environment. Kdjdpfxevvkipj Ah Eot

Condition: used, CNC universal tool grinding machine SCHÜTTE, type BU 400 CNC 4 Machine – Defective – without control system Machine not operational – electrically non-functional – without CNC control Kdedpfx Ahsd Rmcmj Est Manufacturer’s No.: Year of manufacture 1990 4 axes (X, Y, Z, and R) Table clamping surface 1300 x 250 mm Distance between centers 700 mm Distance between centers (height) 155 mm Grinding length (X-axis) max. 400 mm Grinding width (Y-axis) max. 260 mm Grinding spindle speed max. 6000 rpm Grinding spindle drive 3 kW Mains connection 380 volts, 50 Hz, 25 amps - CNC control system removed Space requirement L x W x H 3800 x 2400 x 2300 mm Weight 3000 kg Machine not functional, CNC control system missing. Mechanically in good condition, ideal for retrofitting with a new control system Suitable as a source of spare parts or for rebuilding with a new control system

Condition: like new (used), Year of construction: 2023, operating hours: 100 h, functionality: fully functional, machine/vehicle number: 91.0651.90.11D, total height: 2,000 mm, total length: 2,000 mm, total width: 2,000 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 800 rpm, type of input current: three-phase, grinding wheel diameter: 180 mm, overall weight: 1,000 kg, grinding spindle speed: 2,000 rpm, workpiece diameter (max.): 225 mm, We offer this Wendt OPRA 200V tool grinding machine in like-new condition, year of manufacture 2023. Manufacturer: Wendt Model: OPRA 200V Year of manufacture: 2023 Condition: as new Category ID: 1166 Type ID: 307 Machine type: tool grinding machine Kdedpeyh Rklefx Ah Eet If you have any questions or need more information, please feel free to send us a message or call us.

Condition: good (used), Year of construction: 1980, Grinding machine with an adjustable clamping bar, up to a maximum of 1200 mm. Maximum workpiece thickness: 30 mm. Kdjdpfjzczlrsx Ah Est

Condition: new, Year of construction: 2026, CORMAK SM150D Belt Grinder The CORMAK SM150D belt grinder is an industrial machine designed for intensive operation in production plants, locksmith workshops, and tool rooms. It is a metal belt grinder that combines high grinding efficiency with an effective dust extraction system, ensuring safety, cleanliness, and comfort in everyday use. Its solid steel construction and large worktable surface guarantee stability and precision, even when processing large components. Main Advantages Two belt speeds (14.5 / 29 m/s) – allows adjustment of speed to the type of material and nature of work (coarse or finishing grinding). Integrated dust extraction system – ensures a clean and safe working environment without the need for external dust collection units. Kdsdpjxrzgtsfx Ah Eot Stable steel construction – effectively reduces vibrations, improving repeatability and machining quality. Large worktable (480 × 150 mm) – allows comfortable handling of larger workpieces. Stepless grinding angle adjustment – enables precise positioning of the belt relative to the workpiece. Quick belt change system – minimizes downtime and improves work efficiency. Design and Technology The stationary CORMAK SM150D grinder is built on a welded steel frame, ensuring rigidity and resistance to dynamic loads. The integrated extraction system provides highly efficient removal of dust and grinding debris. A 2.8 kW motor delivers sufficient power for demanding machining tasks. Precision and Efficiency Thanks to the use of a 150 mm wide and 2000 mm long belt, the machine provides a large contact surface, reducing processing time and increasing efficiency. The two belt speeds allow for a quick switch from aggressive material removal to fine surface finishing. The ergonomic design and spring-loaded belt tensioning system ensure proper belt tension throughout the work cycle. Applications The CORMAK SM150D metal belt grinder is suitable for use in: production plants working with steel, stainless steel, and aluminum, welding and locksmith workshops, surface preparation and finishing departments, grinding edges, welds, and flat surfaces. Standard Equipment Stable steel base with tilt adjustment Grinding belt 2000 × 150 mm Built-in dust extraction system with bag and Ø100 mm ports Spark and dust protection cover Adjustable protective shield Technical Specifications Parameter Specification Abrasive belt dimensions (L × W) 2000 × 150 mm Belt speed 14.5 / 29 m/s Motor speed 1400 / 2800 rpm Motor power 2.8 kW Machine dimensions (L × W × H) 700 × 540 × 1130 mm Weight 90 kg Power supply 400 V Extraction port diameter 2 × Ø100 mm Worktable dimensions 480 × 150 mm Chip bag diameter Ø100 mm Chip bag length 500 mm

Condition: good (used), Year of construction: 1987, functionality: fully functional, machine/vehicle number: 31.211.014, center height: 225 mm, grinding length: 1,000 mm, grinding wheel diameter: 400 mm, grinding diameter: 500 mm, workpiece diameter between centers: 500 mm, Equipment: rotational speed infinitely variable, Kellenberger UR 175x1000 CNC Kelco 70, fully functional Height increased from 175 to 225 (can be reversed) Machine no. 31.211.014, year of manufacture: 1987 Prepared for internal grinding attachment Accessories: 1x grinding wheel flange, left 1x grinding wheel flange, right 1x steady rest with various dressing tool holders 1x workpiece magnet 1x paper band filter Kedpfoyyur Iex Ah Esdt No warranty, guarantee, or return Available immediately, ex works If required, transport can be arranged.

Condition: used, Year of construction: 2008, functionality: fully functional, machine/vehicle number: 146978, Knuth Surface Grinding Machine Flat HFS 2500C Working Area & Capacities Table dimensions: 250 x 500 mm Grinding area (max.): approx. 500 x 250 mm Maximum workpiece weight: 180 kg Distance spindle center to table surface: 450 mm Travel Distances & Feeds Longitudinal travel (X-axis): 560 mm Cross travel (Y-axis): 275 mm Hydraulic table feed (X): 7 – 23 m/min Rapid traverse cross (Y): 990 mm/min Rapid traverse vertical (Z): 460 mm/min Spindle & Grinding Wheel Grinding spindle motor power: 2.2 kW Grinding wheel dimensions: 200 x 20 x 31.75 mm Graduation: Y-axis 0.02 mm / Z-axis 0.005 mm Dimensions & Weight Machine dimensions (LxWxH): approx. 2650 x 2150 x 1675 mm Total weight: approx. 1800 kg Kdedpfx Asy H Dg Ieh Ejt

Condition: ready for operation (used), Weight: 2.2t, including documentation. Kjdpfx Ahomqly Uo Ejdt

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and maximum speed - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections Kdodpfx Asuxfu Njh Est - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Pr...

Condition: ready for operation (used), Year of construction: 2008, grinding length: 1,600 mm, grinding width: 630 mm, Surface grinder 1600 x 630 M7163x16100, magnetic table size 1600 x 630, machine length 5400mm, depth 2500mm, height 2600mm. Automatic feeds in the X and Y axes. We are the first owners; the machine is used on average for a few hours a month for service-related grinding. Year of manufacture: 2008. Power: 22KW, 60A. Shipping costs are borne by the buyer. We can arrange complete container shipping, including packing and loading. Here are two packing options: Option 1 Packing on a pallet + aluminum foil and moisture absorbers Requires a 40' HC container. This is the recommended option, as the vacuum foil and absorbers create a protective barrier against moisture and salt. Kedpfx Aoy Shzash Eodt Cost, including loading and securing the machine in the container: 1800 EUR (net). Option 2 Packing without a pallet, aluminum foil, or absorbers. Loading only into a 40' OT container. Cost: 850 EUR (net). Note: In this case, the machine will be more exposed to moisture and salt. Example cost of TRANSPORT ORGANIZATION SERVICE – freight forwarding (all-in), loading Częstochowa, PL, unloading 121001 India, IN, 40 HC, port-to-port, approximately 40 days: 5,050.00 USD.

Condition: ready for operation (used), Year of construction: 2011, DELTA LC 500 – Circular table grinding machine - CE marking - Year of manufacture 2011 - Magnetic table – Rotary table 500 mm - Max. grinding diameter 500 mm - Distance column – grinding spindle axis 315 mm - Grinding height max. magnetic clamping plate – grinding wheel 215 mm - Grinding spindle speed 2840 rpm - Fine adjustment via micrometer 0.01 mm - Coarse adjustment (height adjustment) motorized via keyboard - Spindle motor 3 kW - Dimensions of the grinding wheel 200x80x78 mm - Machine enclosure Kdsdpfx Ahszkvz Ns Est - Coolant system - Documentation Dimensions: L x W x H 1.3 x 0.8 x 1.8 meters / Weight 800 kg Errors and omissions excepted.

Condition: used, Year of construction: 1995, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Teilüberholte Maschine mit Messprotokoll nach Neumaschinentoleranz NEUE Steuerung Eckelmann ENC mit BEMA Schleifsoftware Kdsdpfsyatx Sjx Ah Eot KEL-ASSIST für Kelco 90 numerisch gesteuerte B-Achse Innnschleifrinrichtung Dia 80mm Schleifscheibe links Durchmesser 400mm Schleifscheibe rechts Durchmesser 300mm Innenschleifspindel HJN 828 hydraulischer Reitstock Mikroverstellung KEL SET Messsystem

Condition: used, grinding diameter 250,350,450 mm grinding length 1000 mm centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø Kdsdev I Eq Sopfx Ah Ejt 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m Ready for delivery, with 12 month warranty in germany and neighbouring countries! Geometrically overhauled and repainted with new electrics. In KELLENBERGER quality!!! -Digital display in 2 axes. Resolution x-axis 0.5my -Modern workpiece headstock with cone MK5 -Modern tailstock with cone MK3 -Modern hydraulic unit -Paper belt filter Further accessories on request

Condition: good (used), Stock number: 3062 Kdjdoydhn Njpfx Ah Eet Manufacturer: Mikromat Model: SWPO 50 Year of manufacture: Machine number: 389236 Directly machinable area: 10 x 10 mm Indirectly, via workpiece shifting: 250 x 60 mm Maximum thickness: 48 mm Grinding wheels: 150 mm Spindle speed: 3,500 rpm Drawing table: 156 x 120 mm Table movement x-y: mm Grinding wheel support x-y: 130 – 150 mm Support rotation: 90° left/right Support swivel range: 10° left/right Grinding head rotation: 35° left/right Grinding head swivel: 30° / 10° Grinding motor speed: 2,800 rpm Equipment: Projector, 25x magnification Accessories: Total power requirement: 1.3 kW Weight: 0.9 t Dimensions: 1,600 x 1,200 x 1,600 mm Condition: Good

Condition: good (used), Tos Hostivar cylindrical grinding machine Kodpfxjq H Ap Ns Ah Eedt Type: 1U X-path: 900 mm bed: 900 x 140 mm Turning diameter bed: 260 mm Chuck diameter: 120 mm Diameter grinding stone max: 320 mm Dimensions: 150x105x140 cm LxWxH

Condition: ready for operation (used), Year of construction: 1988, functionality: fully functional, overall weight: 7,500 kg, grinding diameter: 300 mm, controller model: Siemens Sinumerik 840D Solutionline, No minimum price – guaranteed sale to the highest bidder! The control system was upgraded to a Siemens Sinumerik 840D Solutionline in 2014. The new control system was overhauled in 2016! TECHNICAL DETAILS Ksdpfjzwmz Tsx Ah Esdt Spindle speed range: 170–18,000 rpm Grinding diameter: 20–300 mm Swinging diameter: 350 mm (500 mm) Workpiece length: 300 mm (1,300 mm) Recommended grinding depth: up to 300 mm Center height above the workpiece table: 200 mm (300 mm) Center height above the grinding table: 330 mm (430 mm) Workpiece spindle bore: 50 mm (70 mm) Grinding table, Z-axis Total grinding table travel: 650 mm (950 mm) Resolution: 0.001 mm Rapid traverse: 12 m/min Grinding feed rate: 0–9.99 m/min Feed rate: 0–99.99 m/min Incremental feed value during reversal: 0–0.999 mm Grinding table, X-axis Total grinding table travel: 150 mm Resolution: 0.001 mm/rev Rapid traverse: 5 m/min/rev Grinding feed rate: 0–5 m/min/rev Feed rate: 0–99.99 mm/min/rev Incremental feed value during reversal: 0–0.999 mm/rev Workpiece spindle head, B-axis Swivel range: −32° (−23°) to +2° Resolution: 0.0001° (0.36″) U-axis Total travel: 300 mm Resolution: 0.001 mm/rev Traverse speed: 5 m/min MACHINE DETAILS Control system: Siemens Sinumerik 840D Solutionline Machine weight: approx. 7.5 t Space requirement: approx. 5.00 × 4.00 × 2.20 m

Condition: excellent (used), with internal grinding attachment Center height 125 mm Distance between centers 600 mm Grinding wheel 400 x 40 x 127 mm Kdodpfx Aheiu E Tro Eet Misc.accessories MARCELS MASCHINEN AG

Condition: used, Maximum grinding length: 1000 mm Maximum wheel diameter: 320 mm Bore: 30 mm Kdsdev Taafjpfx Ah Eet Manufacturer: TOS

Condition: used, Year of construction: 1991, functionality: fully functional, machine/vehicle number: C4656, grinding length: 4,100 mm, grinding width: 200 mm, Reform AR41 Type 7 C4656/91 Year of manufacture: 1991 Grinding length: 4100mm Grinding width: 200mm Workpiece height: 190mm Table clamping area: 4169x202mm Segment head diameter: 250mm Spindle diameter in the front. Bearing: 45mm Swivelling: 2° Max. torque: 2x45.8Nm 2x grinding motor 7.5kW Feed: 2000-35000 mm/min Max. speed: 1460 min/-1 Total power requirement: 30 kW Kdjdpfotqtppjx Ah Est Heidenhain digital display Additional grinding device ZS 7.5kW Swivelling clamping table via swivel gear Paper belt filter cleaning including pumps Central lubrication system Machine weight approx. 8.2t Space requirement approx. 9.5x2.6x2m

Condition: ready for operation (used), ELB SWN 5 VA II Horizontal Surface Grinding Machine Kodpfx Ahoy Dcpcs Eedt - Grinding area X/Y/Z: 525x375x255 mm - Magnetic chuck: 700x300 mm - Table clamping area: 900x250 mm - Table longitudinal stroke: 10-625 mm - Maximum table load: 280 kg - Table feed: 1-30 m/min - Reciprocating grinding: 3-30 m/min - Distance from table to spindle center: 525 mm - Vertical feed rate: 2-180 mm/min - Adjustable infeed: 0.001-2 mm - Grinding wheel speed: 3000 rpm - Coolant system - Machine feet - Documentation - Complete technical data – see photos Dimensions (LxWxH): 2.7x2.2x2 m / Weight: 3500 kg Subject to errors and input mistakes

Condition: excellent (used), Year of construction: 1988, functionality: fully functional, Jung JF 520 D year of manufacture 1988 magnet 500 x 175 mm max. grinding area 600 x 220 mm variable speed variable magnetic field strength automatic start Kdjdpfozba Ngox Ah Eet diaform coolant/filter tank 3 x flange 1 x clamp documentation machine is powered on for inspection

Condition: ready for operation (used), functionality: fully functional, The frames of the RSM series machines have a heavy-duty design and long, supported guides. The table can rotate and the precisely adjustable hydraulic feed moves smoothly in the longitudinal direction. WORKING AREA Height point 135 mm Workpiece length 640 mm Grinding length 500 mm Grinding diameter 8 mm - 200 mm Inside diameter without support 25 mm - 100 mm Workpiece weight between centers (max.) 50 kg Internal depth 125 mm Ksderi Ngyjpfx Ah Eodt Table miter cuts (max.) -3° / +9° R / L Peripheral speed 38 m/s DIMENSIONS AND WEIGHTS Grinding disc dimensions400 mm x 50 mm x 203 mm Grinding wheel internal dimensions (max.)50 mm x 40 mm x 16 mm Grinding disc dimensions (min.)45 mm x 35 mm x 10 mm Dimensions (length x width x height)2.5 m x 1.6 m x 1.5 m Weight 2500 kg

Condition: not inspected (used), Year of construction: 1987, functionality: unexamined, machine/vehicle number: 20119, We offer this Studer S35 cylindrical grinding machine, ready for use, manufactured in 1987. Manufacturer: Studer Model: S35 Year of manufacture: 1987 Condition: ready for use Category: 1373 Type: cylindrical grinding machine Kjdpfx Aezvvzyjh Eedt If you have any further questions or require additional information, please feel free to send us a message or call us.