Used Roller Hot Melt Glue Applicator for sale (20,328)

Condition: used, Year of construction: 2021, functionality: fully functional, Dürr Ecopure VAR 2206 Thermal Oxidizer with Flue Gas Cleaning (2021) For burning liquid and gaseous waste streams including fluorinated gases, e.g. PFAS, and recovery of aqueous hydrogen fluoride Hfedpfx Aez Ai Tpjknsl Emissions limits SO2 ≤ 100 mg/Nm³ NOX ≤ 30 mg/Nm³ CO ≤ 50 mg/Nm³ CF4 ≤ 70 mg/Nm³ HF ≤ 1 mg/Nm³ NH3 ≤ 2 mg/Nm³ Comprising Direct fired thermal oxidizer Hot gas cooling and acid recovery Alkaline wet scrubber Honeycomb selective catalytic reduction deNOx system >1M cost spare parts Direct fired thermal oxidizer Including 2x natural gas combustion chambers and burners - High calorific liquid waste requires safe ignition supplemental hydrogen supply for acid formation - Gaseous waste streams injected via nozzles downstream and close to the burner - 1.5MW multi-fuel natural gas & liquid waste (minor fuel stream) burner with natural gas capacity up to 200Nm3/h - 1400C normal, 1540C max allowable temperature destruction of pollutants to reduce emissions with 3.28 MW thermal energy transfer - 2 seconds minimum residence time in combustion chamber at 1400C - 1,800mm combustion chamber internal dia. - Approx 300mm refractory lining - 2,400mm combustion chamber external dia. - 12,000mm combustion chamber internal length - 3.28MW maximum thermal capacity - 4,900Nm3/h, 60mbar, 14kW combustion air fans One chamber is active, the other one is on standby and can be prepared, repaired, or maintained. This allows minimizing shutdown and changeover time to only several days Wet scrubber hot gas cooling and acid recovery SGL Carbon Diabon HT-PQ 850 graphite pipe quencher - 6,000 Nm3/h capacity flow - 1,100 mm dia. - 2,000mm high - pumps SGL Carbon Diabon THX-RS falling film absorber shell & tube heat exchanger - 1,100mm dia. - 4,500mm tube length - 595 no. tubes - 22mm tube internal dia. - Graphite, carbon steel - pumps Quench vessel - PP/FRP - 1,100mm dia. - Approx. 6,000mm high 2x Scrubber absorber columns, each - Shell FRP/PP - Internals PP - 1,000mm dia. - 11,000mm high - Pumps - Dosing station FRP 5m3 Emergency water tank - 1,600mm dia. - 3,000mm high - 3kW heating 2x Teblick 100,000L HDPE hydrofluoric acid tanks (2019) Honeycomb selective catalytic reduction deNOx system - 5,900Nm3/h, 130mbar, 42kW induced draft fan - 320 kW gas/gas heat exchanger - 500 kW capacity reheat burner - 1.2m deNOx honeycomb catalyst Clean gas outflow Stack with flow & temperature measurement Spare parts include - 200 items of sensors, pumps, valves, gaskets, joints etc. - Graphite quencher - Falling film absorber With the redesign and maintenance support of Dürr, the system could also - be adapted to other halogenated gases with bricks to be selected according to gas application - cope with the presence of VOCs or contaminated air - larger volumes with the addition of a small lance for 15kg/h liquid injection

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Working width: 30 cm Adjustable glue application rate Single-sided glue application Emergency stop button (mushroom switch) Feed table with rollers Total table length: 130 cm Weight: 150 kg 380 V Year: 2003 Hsdpfx Aszxpvvsknsfl

Condition: used, Year of construction: 2023, Special price – Showroom machine Garbsen INDUSTRIAL AUTOMATIC EDGE BANDING MACHINE stefani md (the images of the machine are not binding with regard to the actual features specified below) KEY FEATURES EDGE BANDING OF SOLID WOOD UP TO 15 MM THICKNESS: SIMPLE AND FUNCTIONAL PROCESSING OF EDGES WITH LARGE DIMENSIONS "SGP" GLUE TANK: USE OF EVA AND POLYURETHANE GLUE FOR A PERFECT GLUE JOINT "STARTOUCH" CONTROL: A TOUCH IS ALL IT TAKES TO OPERATE THE MACHINE GENERAL FEATURES Automatic single-sided edge banding machine for applying edge banding with hot melt adhesive to the four sides of straight panels and for subsequent finishing. Machine frame and longitudinal supports made of cold-rolled steel in a box construction, manufactured in a single element, for high rigidity and vibration-free operation to accommodate the working units. Openings with slides for discharging any remaining chips to the floor. Upper pressure beam made of thick-walled steel construction and with columns made of cast iron, for a vibration-free structure where the working units are attached. Pressure rollers on the feed chain in a double row, made of rubber with a high coefficient of friction and with sliding on bearing rollers. Device to protect the pressure rollers from any remaining chips. Electronic adjustment of the upper pressure unit, depending on the panel thickness. Upper working units attached to the pressure beam or mechanically connected to ensure automatic adjustment when changing the panel thickness. Lower working units attached to the machine frame or to the longitudinal support, for a precise reference to the panel. All high-frequency motors are operated via frequency inverters. Protective cover for all units positioned after the gluing unit. Windows made of polycarbonate ensure a good view of the units during processing. Interior lighting of the cabinet. Protective cover with sound-absorbing material for lower noise emissions during processing. The spacer on the infeed guide allows the machine to be fed in the correct spacing. The spacing is automatically adjusted to the selected feed speed. Extraction nozzle arranged on the soundproof hood. Swivel control panel in an ergonomic position at the machine infeed. The electrical system complies with current regulations. Electrical components housed in a metal housing, attached to the machine frame and provided with doors for convenient access during any maintenance work. Panel feed The panel feed is carried out via a feed chain consisting of rubber sliding blocks with a high coefficient of friction, attached to a 1-1/4" industrial chain. The chain slides on 2 guides made of hardened and ground steel, a round guide and a flat guide, to guarantee a straight feed and protect against lateral displacement. Automatic lubrication of the chain. The amount of lubricating oil is optimized by the control system depending on the panels being processed. Support roller track externally and positioned along the entire length of the machine; consisting of an extendable opening system with sliding on linear bearings and plastic sliding rollers with steel pivot pins. "STARTOUCH" CONTROL Main features: 12" touchscreen color display Graphical representation of all processing units and their status (on/off) Hfodpfx Akezc Ilxjnol

Condition: used, Year of construction: 2010, Used machine Year of manufacture: 2010 Features and technical specifications: Right-hand configuration 2 side tables are still in their original packaging H&H / HARDO TH 1020-V46 BV DA (twin unit) Max. application width: 2,040 mm (2 × 1,020 mm) Configuration: Twin-unit system, both machines can also be operated individually Application roller: reinforced version Application roller diameter: 46 mm Knurling on application roller: 0.5 mm Bearings: reinforced roller bearings Bearing shells: hardened Squeegee: pneumatically operated, needle-bearing mounted Main bearing lubrication: external lubrication, filled using a hand-operated grease gun Tank seal: adjustable and replaceable without removing the application element Application speed control: via frequency converter Speed range: 3.2 – 19.3 m/min Control: Potentiometer Display: digital speed display Pressure rollers: 2, silicone-coated Pressure rollers, length: 2,040 mm Pressure rollers – diameter: 159 mm Pressure rollers – Actuation: pneumatic Pressure rollers Lowering: automatic after the drive motor is switched off Height adjustment of material feed: electrically driven in manual step mode Stroke of application unit: 0 – 200 mm Conveying height: 925 mm (lower edge of material) Drive for pressure rollers: separate drive Motor: including motor console, mounting and cladding Additional application speed control: via separate frequency converter Hodpfx Aszk Nzvjknjfl Additional speed range: 3.2 – 19.3 m/min Additional control: Potentiometer Additional display: digital speed display Base frame: aluminium profile system Stands: 2, made from anodised aluminium plates Adjustable feet: Adjustment range ±25 mm Material flow direction: right to left Heating control: Timer (daily and weekly programme) Temperature control: electronic with digital actual value display Melting tank volume: 2 × 25 litres Heating capacity: 2 × 8.0 kW Rated power: 18.5 kW Control voltage: 24 V Rated frequency: 50 Hz Operating voltage: 400 V Phases: 3 Fuse rating: 63 A Compressed air connection: < 8 bar Application: Melting and application of non-reactive hot-melt adhesives Weight: 1,560 kg Availability: at short notice Location: Rhineland-Palatinate

Condition: like new (used), Year of construction: 2013, functionality: fully functional, overall weight: 500 kg, MAKOR TF/P PLUS coating machine 19.06.6512 TYPE TF/P Plus Max. working width 150 mm Max. height 120 mm Adjustable feed rate max. 140 m/min Upper pressure rollers with drive x 6 Pressure force adjustment via pneumatics Lower pressure rollers with drive x 6 CE marking Year of manufacture 2013 Product description: - Paint without waste - Robust and efficient transport with 6 motor-driven pressure units. - Various application heads guarantee results, even for filling and defect repair products. Designed for continuous application of coating, gesso, and paint on strips, picture frames, and profiles with an extrusion system, using a correspondingly shaped steel counter-template. Construction made of steel sheet and tubular steel. Guaranteed forward movement via no. 6 lower metal rollers and no. 6 upper rubber pressure wheels, variable with adjustable speed via an inverter. The upper pressure wheels are mounted on freewheel bearings to reduce uneven wear. Pneumatic distribution panel equipped with a selector for engaging the upper pressure wheels and corresponding independent pressure regulators. Hjdpeytc Rksfx Aknsfl OPTION TO PURCHASE THE FOLLOWING MACHINES AT INDIVIDUAL PRICES: 1. Profiling machine for grinding wheels and silicone wheels from the Italian company MAKOR, price €1,500 - Year of manufacture: 2003 - Serial number: 5933 - Diameter of profiled wheel: 160 - 200 mm - Diameter of profiling disc: 180 - 200 mm - Weight: 280 kg 2. MAKOR ST/100 film slitting machine, price €1,200 3. MAKOR TEP 3000 conveyor belt, price €700

Condition: used, Holzher arcus 1334 edge banding machine pre-milling cutters glue application, cartridge glue pneumatic pre-trimming guillotine pressure rollers trimming cutters up-and-down milling cutters R1 R2, CNC-controlled Hfsdpfez Ai Utsx Aknol corner rounding profile trimming flat trimming Maximum edge banding height: 60 mm Edge band thickness in roll: 3 mm Feed speed: 8-18 m/min

Condition: good (used), Year of construction: 2018, functionality: fully functional, type of input current: three-phase, total width: 2,400 mm, The Lamina Gluer is a manually fed, in-line folding, gluing, and taping machine. Thanks to its smart design, it can handle different sizes and materials. Tool-free setup enables quick changeovers, even for short production runs. Optional machine features include cold glue, rear support unit, working station, tape applicator, and more. The Lamina Gluer is a straight-in-line gluing machine built on a robust frame made of extruded, anodized aluminum profiles. The machine offers manual feeding as standard, with an optional automatic feeder for die-cut, creased, and slotted materials. The operator positions the blanks, and the hot melt unit applies adhesive as the material passes through the machine. Glue line length and exact position can be pre-set using a programmable logic controller (PLC) and a touchscreen interface. A system of pressure rollers ensures perfect adhesion and guides glued blanks onto a pull-out tray, which is easily adjustable for various sizes. The machine comes equipped with adjustable and interchangeable side guides, enabling efficient gluing of 2-piece boxes. The Lamina Gluer is supplied ready for connection to electric and pneumatic systems. The Lamina Working Station is an additional option for the Lamina Gluer. Products are fed through the Gluer, which applies pre-programmed glue lines, and continue into the Working Station, where they are positioned on vacuum belts. A second piece is mounted and positioned using side lays and pneumatic stops for high-quality finishing. The unit can be adjusted for a wide range of products, from single- to multi-part displays and boxes, large back supports, shelves, and more. Transport The material is conveyed by four vacuum belts that bring the sheets to a stop bar for subsequent operations. The vacuum is generated by a fan that secures the sheets for optimal handling and precise registration. During production, the operator has full access above the sheets for additional mounting, thanks to the vacuum belt design. Pressure Rollers Material passes through two pressure rollers at the machine’s end for optimal adhesion. Registration Hjdpfoxwcwwjx Aknjfl Registration accuracy is +/- 1 mm and is achieved by a combination of photocell sensors and pusher guides. The operator uses a side lay guide to simplify the mounting process at the station.

Condition: used, Control card, hot melt adhesive, output card, control, edge banding machine, edge banding machine -Manufacturer: HOMAG HOMATIC -Type: 4-008-39-0001 -Type: 4008390001 -Number: 1x control cards available -Price: per piece -Dimensions: 100/40/H170 mm Hfjdpfx Akjcc Ap Sjnsl -Weight: 0.34 kg

Condition: used, Year of construction: 2016, The DT-250 series is a hot-bar/ACF bonding machine, intended for connecting flexible circuits, PCBs, and displays, among other applications. The DT-250 features a manually operated 2-position front/rear slide with approximately 200 mm of travel. Manufacturer: Unitek Eapro B.V., Helmond, Netherlands Type: ACF DT-250-GH Serial number: 0620905 Year of manufacture: 2006 Power supply: 230 V Current: 6.3 A Phase: 1-phase CE marking Type: ACF DT-250-GH Serial number: 0620905 Year of manufacture: 2006 Power supply: 230 V Current: 6.3 A Phase: 1-phase CE marking Property Specification Type DT-250 Technology Pulsed Heat / Hot Bar Application ACF bonding / heat-seal bonding / reflow Slide Manual, 2 positions Travel 200 mm Bonding head SH500 Hfodpfxozzau Uj Aknjl Maximum force 30–500 N Pneumatic operation Yes Air pressure 4–8 bar Thermode temperature up to approx. 600 °C Temperature control Uniflow pulsed heat Workpiece/fixture up to approx. 160 × 160 mm

Condition: good (used), Year of construction: 1999, functionality: fully functional, machine/vehicle number: 034108905, BOBST 100 II - A2 folding and gluing machine, manufactured in 1999. This efficient machine is designed for the production of straight-line packaging and packaging with a crash-lock bottom, handling cardboard and corrugated board. It features 6 cold glue applicators and one hot glue applicator. It also has a wheel-fed glue system with a container. It glues at 6 points – with various glue application methods. It includes a cassette for gluing envelopes. The HHS system in this version is very good – it can be used to produce envelopes, Advent calendars, and boxes. The machine can be inspected at our printing facility in Szczecin. Hfedpfxozwmvqj Aknol

Condition: good (used), machine/vehicle number: 110283-110155, Year of construction: 2012, AUTOMATIC LINEAR HANDLE APPLICATOR MACHINE MANUFACTURER AND&OR MODEL 50SIA3000R&P2 SERIAL 110283-110155 YEAR 03/2012 CAPACITY 3000 Bph Included: * Bunker for handles & tranportation convejor * Handle side rejection system OMRON Hfodpfxsquuv Is Aknsl ALSO FOR SALE : TRINE T4400 Labelling machine €17,800 with HOT MELT glue. S/N: 032M44045 Labelling speeds: 60 to 350 cpm USED Wrap around labeller used for PET bottles. Used with 0.33 / 0.5L / 1.5L Volume

Condition: used, Year of construction: 2009, Second-hand machine Year of manufacture: 2009 Condition: factory-refurbished by Osama Technologies Features and technical specifications: - Automatic gluing machine with two rollers - Working width: 1000 mm - Usable working thickness: 0–100 mm - Application rollers Ø 185 mm - Feed speed 24 m/min - Work surface height: 800 mm Hedpfxozk Nxbs Aknofl - Groove spacing between rollers: 2 mm - Motor power 0.37 kW - Glue distribution tank made of painted sheet metal - Water tank made of galvanised sheet metal - CE marking - Voltage 400/50/3Ph Availability: at short notice Location: Röllbach

Condition: used, Year of construction: 2020, Edge banding machine K36, 1 unit, with PLC control (incl. touchscreen) and hot melt adhesive application to the workpiece; rabbeting cutter (incl. DIA tool) up to 3 mm cutting depth; glue reservoir with quick-change reservoir preparation, incl. adhesive dispensing device; high-frequency miter saw station (approx. 16,000 rpm); high-frequency milling station (approx. 16,000 rpm with separate pneumatic milling adjustment); corner rounding cutter (min. workpiece length 300 mm, max. workpiece height 40 mm); radius cutting blade; flush cutting blade (incl. pneumatic extraction); cleaning station; 1 free space for a 2nd milling station or a slot cutting saw (slot cutting saw only if the cleaning station is removed); robust chain drive, ball-bearing mounted double roller pressure pad, viewing window from the rear of the machine, extendable workpiece support, signal lamp for workpiece sequence. Technical data: Max. edge thickness: 3 mm Max. rabbet thickness: 3 mm Min. workpiece height: 8 mm Max. workpiece height: 60 mm Max. rabbet height: 40 mm Min. workpiece length: 160 mm Feed rate: approx. 10 m/min Ready for operation: approx. 5 min. Power consumption: (400V – 3Ph – 50 Hz) Working height: approx. 900 mm Machine dimensions: approx. 5250x1250x2050 mm (L x W x H) Weight: approx. 1700 kg Dust extraction nozzle: 1x140 mm + 1x80 mm 8 mm version K36, 1 unit, quick-change fitting for corner milling cutter K36, 1 unit, extra charge for multi-radius cutting blade (R2/R1) K36, 1 unit, rabbeting up to 60 mm workpiece thickness K36, 1 unit, release agent spray device, plate K36, 1 unit, cleaning agent spray device, plate K36, 1 unit, nesting for milling station K36, 1 unit, nesting for radius cutting blade K36, 1 unit, pneumatic 3-point adjustment K36, 1 unit, Airtronic K36, 1 unit, extension of the support in the infeed and outfeed by 440 mm each; 1 unit. With the help of the plug-in extension of the infeed and outfeed of the table extension, Hebrock offers a solution for an enlarged support surface for improved workpiece handling by 450 mm. Level monitoring without reservoir, 1 unit. Thanks to a sensor on the top of the glue application roller, the operator can be shown a minimum glue level. A warning is displayed on the screen. Once this warning appears, a maximum panel processing length of 100 m (19 mm chipboard) is possible. Hedpfjzvhk Hex Aknsfl Ball bearing for corner rounding cutter, 24.1 mm, 1 unit Ball bearing for corner rounding cutter, 24.2 mm, 1 unit Packaging surcharge, 1 unit Additional quick-change reservoir incl. level sensor Manufacturer: Hebrock Type: 36/14/1 Article No. H36/14/1, 1.0 unit Additional change motor for corner milling cutter K36 Manufacturer: Hebrock Type: 36/08/2 Article No. H36/08/2, 1.0 unit R1 Location: Supplier

Condition: ready for operation (used), Year of construction: 2014, operating hours: 1,174 h, product length (max.): 4,770 mm, This HOMAG KDF 230 edgebander was manufactured in 2014. It has processed a total of 65,428 workpieces and 108,908.92 meters of edge length. The machine features a digital touchscreen control panel and a multi-flexible overhead dust extraction system. If you are looking to get high-quality edgebanding capabilities, consider the HOMAG KDF 230 machine we have for sale. Contact us for further details. - Total Operating Hours: 1174:30.12 h- Total Workpieces Processed: 65,428 Stck- Total Edge Length Processed: 108,908.92 m- Application Unit Temperature: 190 °C (Target), 76 °C (Actual)- Feed Speed: 11 m/min- Working Height: 950 mm- Pneumatic Connection: min. 6 bar- Overall Machine Length: 4,770 mm- Workpiece Width min.: 70 mm (at 8-22 mm thickness), 120 mm (at 23-40 mm thickness), 150 mm (at 41-60 mm thickness)- Workpiece Overhang: 38 mm- Workpiece Thickness: 8 - 60 mm- Edge Material Roll: 0.4 - 3 mm (max. cross section 135 mm² for PVC, 100 mm² for veneer, roll diameter max. 830 mm)- Edge Material Strip: 0.4 - 6 mm (max. cross section 165 mm²)- Control System: EasyTouch 2- Operating Voltage: 400 V / 3Ph / 50Hz- Joint Trimming Unit: 2 x 2.2 kW, 200 Hz with DIA cutter set (100 x 65 x 30 mm, Z=3, max. workpiece thickness 60 mm)- Gluing Unit: Standard A6 with workpiece pre-heater and quick-change application unit (suitable for Granulate / PU)- End Trimming Unit: 2 x 0.18 kW, 200 Hz, 12,000 rpm (swivel range 0-15 degrees) with pneumatic adjustment- Fine Trimming Unit: 2 x 0.27 kW, 200 Hz, 12,000 rpm with pneumatic adjustment (chamfer/radius/straight), DFC combination cutters, and multi-roller sensing - Corner Rounding / Form Trimming Unit: 1 x 0.35 kW, 200 Hz, 12,000 rpm (max. edge thickness 3 mm, max. workpiece thickness 60 mm, min. workpiece length 250 mm) with structural floor attachment- Profile Scraper Unit: Quick-change heads, pneumatic adjustment, and special multi-roller sensing- Glue Joint Scraper Unit: Included with top/bottom tracing and dust extraction- Buffing Unit: 2 motors x 0.09 kW, tilt and height adjustable- Pressure Line: Smooth PU top pressure rollers- Additional Features: Hood internal lighting, feed fence extension (+300 mm), automatic edge infeed (KDX 1210/1400) Hjdpszzwhfsfx Aknsfl Technical Specification Feed Speed 11 m/min

Condition: good (used), CMC Italia Gemini Gem 52 Case in gluer Machine in perfect condition, like new. Manufactured by CMC Italia, Italy. This gluing device allows for the application of glue to both sides of the book block. Two gluers, smooth glue thickness adjustment. Chrome rollers, adjustable glue thickness. Hfedezlggljpfx Aknjl Very easy to clean. Working width: 520 mm Power supply: 380 V Weight: 250 kg Made in Italy.

Condition: used, Year of construction: 2018, machine/vehicle number: 10619-1, MEYPACK VP 451 tray and wrap-around packaging machine Fully automatic machine for packing beverage cans into trays and wrap-around cartons. Products and formats: - 0.33-litre cans, Ø 66 x 115 mm, loose and in four-packs - 0.5-litre cans, Ø 66 x 168 mm, loose and in four-packs Pack configurations for both can formats: - 4 x 6 loose cans in a wrap-around carton or tray - 3 x 4 loose cans in a wrap-around carton - 2 x 3 four-packs in a tray Output: - Nominal output: 16,000 cans/h - Packaging output: 12 or 24 packs/min, including a 5% capacity reserve Product handling: - Multi-lane bulk product infeed - Four-packs fed transversely on two lanes, with the openings facing sideways - Infeed height: approx. 1,150 mm ± 50 mm - Outfeed height: approx. 650 mm ± 50 mm - Trays and wrap-around cartons leave the machine broad side leading Operating principle: The products are fed continuously in multiple rows, distributed evenly into the lanes of the infeed conveyor using the accumulation principle, and grouped into the required formation. At the same time, a flat tray or wrap-around blank is removed from the magazine and positioned below the grouping station. The servo-driven lowering station receives the product formation and blank and folds the blank tightly around the products. A servo-driven indexing chain then conveys the pre-folded pack through the gluing and compression stations. The finished pack is transferred to the downstream conveyor system via a gravity roller conveyor. Grouped-pack size range: - Length: 200–400 mm - Width: 120–300 mm - Height: 80–200 mm - Tray height: 40–200 mm Packaging material and magazine: - Suitable for almost all commercially available corrugated-board grades; final design subject to approval by MEYPACK - Blank length: 360–1,250 mm - Blank width: 300–700 mm - Magazine capacity: approx. 150 blanks or approx. 400 mm stack height for B-flute board - Flat blanks are separated by vacuum cups and positioned by a belt conveyor - Hot-melt adhesive: commercially available grades approved by the adhesive-unit manufacturer; final design subject to approval by MEYPACK Utilities: - Electrical supply: 3 x 400 V AC, 50 Hz, with neutral and protective conductor; permissible long-term voltage fluctuation ± 5% - Control voltage: 24 V DC - Compressed air: 6 bar, 1/2-inch connection; clean and free from foreign matter, gases and oils Operation and format change: - The machine can be monitored by one operator while performing another task - Operator side can be arranged on the right or left when viewed in the outfeed direction - Fast, repeatable format changes through zero-line design and automatic indexing-chain adjustment - Settings documented in product-specific format lists; clearly assigned and marked change parts Basic machine and components: - Weight: approx. 3,500 kg - Finish: black grey RAL 7021 - Pneumatics: Festo - Hot-melt unit: Nordson Pro Blue - Drives: SEW, protection class IP55 - Control system: Siemens S7 - Operator interface: Siemens Touch Panel TP 1500 - Electrical design in accordance with MEYPACK standard electrical equipment specification E 2017 Included options: - Additional tray takeaway conveyor for manual palletising - Painted-steel roller conveyor with integrated corner transfer, nominal width 350 mm, length approx. 1,100 mm - Two-lane transfer unit with modular belt chain, adjustable side guides on one side and stainless-steel cable duct - Broadband VPN router for remote machine maintenance - Swivel arm for Hfodpoz Abkyjfx Aknol

Condition: excellent (used), Year of construction: 1998, HÖFER LAN 1300 Adhesive Coating Machine For the efficient application of water-soluble dispersions (white glue, etc.) on one or both sides. Coating width: maximum 1300 mm Drive: 0.37 kW geared motor Rubber-coated coating rollers: Ø 170 mm Hsdpfxjza A Aae Aknjfl Grooving for coating quantity: approx. 120 g/m² (for veneers) Constant coating speed: approx. 16 m/min Working height: approx. 900 mm Maximum workpiece thickness: 80 mm Design complies with CE standards Manual feed Operating side: right Including swivel casters Machine dimensions L x W x H = 1750 x 660 x 1300 mm

Condition: used, Year of construction: 2004, Format: 320 ?? 550 mm Equipment: Sheet feeder: Two drum feeders with gripper system Belt conveyor channel for product conveying Surface with rice paper structure to protect the product Front stop made of aluminum Side guides with sorting screws for sheet positioning Screw ejector for precise bow positioning Sheet control system: Double sheet inspection using mechanical thickness measurement Misaligned bow detection using photocell Photocell-controlled activation of the second feeder and glue injection timing Glue unit: Hot melt or cold glue application (configurable) Glue injector with digital keyboard setting Delivery: Double roller press station for optimal adhesion Inclined conveyor belt for shingled product stacking at the exit Control system: SPS control unit Touchscreen control panel Hfodpoyxqxbefx Aknel Safety system with light barriers Technical data: Min. Format 100 ?? 150 mm Max. Format 320 ?? 550 mm Max. sheet thickness 5 mm Maximum mechanical speed 6,000 cycles/hour

Year of construction: 2020, condition: used, functionality: fully functional, overall weight: 1,900 kg, total length: 6,800 mm, total width: 2,850 mm, machine/vehicle number: 30387, We are pleased to offer a used Wehrmann roller conveyor from 2020, equipped with a conical swivel for handling panels and IMA Meinert Drehstation DK type roller feeders. This modern solution enables efficient and precise handling of panels in the production process, ensuring high performance and reliability. It is ideal for industrial applications where efficiency and the quality of component transport are paramount. The option to purchase the entire line is available, including a two-chamber automatic loading station and a double-sided edging machine, the IMA COMBIMA I K/II/R75/760/V/R3. Hfedpfszgch Iox Aknjl

Condition: used, Year of construction: 2010, - Equipped with ISAS 28-position edge magazine - PU gluing unit - With Boomerang return system Single-sided edge banding machine Manufacturer: Homag Type: KAL 310/7/A3 Year of manufacture: 2010 Technical data - Equipped with ISAS 28-position edge magazine - PU gluing unit - With Boomerang return system Edge trimming unit with 2 motors, each 3KW, 150 Hz, 9,000 RPM. Pneumatically controlled for pre-trimming PU gluing unit 34 with PU hot melt unit - capacity max. 6 kg/h Container size 2 kg. QA glue application unit Selectable edges from the ISAS 28-position edge magazine 4 pressure rollers Release agent spray unit, top and bottom Trimming unit WK 13, bevel / straight With 2 motors, each 0.4 KW, 200 Hz, 12,000 RPM. Electropneumatic adjustment of the trimming motors to 2 positions (flush trimming and with overhang) Pre-trimming unit with 2 motors, each 0.55 KW, 200 Hz, 12,000 RPM. With double-roller scanning. With electropneumatic adjustment Shaping trimming unit FK 11 - manual For processing the edge overhangs on the top and bottom edges of the workpiece, as well as for milling the front and rear edges With 2 motors, each 0.4 KW, 200 Hz, 12,000 RPM. Universal trimming unit UF 11 With motor 4 KW, 150 Hz, 9,000 RPM. Swiveling 90°, electropneumatically controlled With HSK 63 F collet for unlocking by push-button Profile scraping unit PN 10 Pneumatic adjustment for moving sideways out of the working area Finishing unit FA11 top/bottom Consisting of: Glue joint scraping blade Cleaning agent application Buffing unit with 2 motors, height adjustment with the upper pressure Machine control via 19-inch touchscreen Return system BOOMERANG ZHR05 Hsdpfxozuyhhs Aknsfl With air cushion table, angled, length 2,000 mm, width 1,000 mm Conveyor belt width 1,100 mm Workpiece parameters: Length 300 - 2,500 mm / Width: 60 - 1,100 mm or Length 300 - 800 mm / Width: 1,100 - 2,000 mm Thickness 8 - 60 mm For 4-sided processing: Min. part size: 300 x 300 mm / max. part size 2,000 x 800 mm With roller strip for supporting wider parts.

Condition: like new (used), functionality: fully functional, roll diameter: 90 mm, total width: 1,300 mm, total height: 600 mm, total length: 3,000 mm, power: 0.55 kW (0.75 HP), type of input current: three-phase, load capacity: 1,500 kg, Complete set of roller conveyors, suitable for the efficient transport of pallets within logistics or production environments. The installation is in excellent condition. Specifications: Height: 600 mm Width: 1300 mm Lengths: Hfsdjyzupcepfx Aknjl 11 x 3000 mm 1 x 2200 mm (equipped with collision guard) Distance between rollers: 125 mm Roller diameter: 90 mm Roller finish: electrolytically galvanized Load capacity: 1500 kg Drive system: SEW R37 DRS71M4 - Type: R37 gearbox with DRS71M4 electric motor - Power: approx. 0.55 kW - Speed: approx. 1400 rpm (motor) - Supply voltage: 230/400 V, 50 Hz - Protection class: IP54 Pallet detection via sensor-equipped switching bar Includes 1 side guide for accurate pallet positioning/control Description: These roller conveyors are designed for reliable and smooth pallet transport. Thanks to their robust construction and galvanized rollers, they are durable and low-maintenance. Ideal for warehouses, distribution centers, and production lines. Currently provided with transport supports; rollers can be interconnected using the supplied connector pieces. Condition: As good as new Application: Ready for immediate use Price per conveyor: €3,250 excluding VAT Contact us for more information or to arrange a viewing. DYST

Condition: excellent (used), Year of construction: 2017, operating hours: 2,000 h, functionality: fully functional, machine/vehicle number: 2017.041.XM.400.004, space requirement length: 6,700 mm, space requirement width: 3,200 mm, space requirement height: 5,000 mm, This is a combination of a hot mixer and a cooler. A typical application is mixing polymers with additives. Hot mixer: working volume of 400 liters, drive power 90 kW, mixing impeller with a tip speed of up to 60 m/s. Vacuum system included (but needs optimization). Filling hopper included. Gravimetric scales for the additives are not included in the delivery. Cooling mixer, volume 1200 liters with a 11 kW drive, cooling jacket for cold water flushing, outlet with a valve. The combination includes the entire steel structure with walkways, control cabinet with frequency converter (400 VAC/50Hz) for the variable drive of the hot mixer. Hjdezl Td Ropfx Aknofl Additional documents can be provided upon request. The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price is quoted without packaging on a pallet.

Condition: good (used), Year of construction: 2015, machine/vehicle number: 0-200-24-0779, functionality: fully functional, input voltage: 400 V, input current: 55 A, input frequency: 50 Hz, type of input current: three-phase, workpiece height (max.): 60 mm, edge thickness (max.): 20 mm, total length: 10,825 mm, Used single-sided HOMAG edge-banding machine for straight edges – KAL 370 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2015 EQUIPMENT / SPECIFICATION BASIC MACHINE - with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness 8 to 60 mm - top pressure with compound V-belt, automatic height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors (clockwise, counterclockwise), 2x4kW, rear motor w. jumping function GLUING SECTION V20, consisting of: - QA60 glue application unit, with PTFE-coating (Teflon), with manual quick-adjustment glue gates - pneumatic clamping of glue application in mount - Pre-melter for EVA glue - Edge magazine, edge thickness min. 0,4 mm to max. 20 mm Edge width (height) max 65 mm - modes: edge rolls, (veneer) strips, solid wood edging - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 4 non-driven pressure rollers. POST-PROCESSING SECTION: - Snipping (end-trimming) unit PK85 horizontal, 2 motors, with straight/chamfer cutting function - Rough trimming 2x1.15 kW, top/bottom - Corner rounding FK11, 2 motors (top/bottom) with various trimming heads, motorised adjustment - Universal trimming unit, (e.g. grooving), 3.5 kW, tiltable, w. electro-pneumatic jumping control - Multi-Profile (radius-) scraping MN11 with automatic positioning by NC-axis (CAN) - Flat scraping (glue joint) FA20, top/bottom, (version with 3 tracer rollers) - Buffing unit FP10, top/bottom Control / software: - powerControl PC 23 PowerTouch - woodCommander 5 Hfsdpfeztl Scsx Aknsl Machine dimensions 1085 x 180 x 235 cm (with opened doors)

Condition: good (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 179056920, Technical characteristics: Work Area - Chuck diameter: 600 mm - Max. workpiece diameter/height: 450 / 400 mm - Distance spindle nose to tailstock origin: 639 mm - X1/X2 axis stroke (effective travel): 335/289 mm / Rapid traverse X: 30 m/min - Z1/Z2 axis stroke: 560/494 mm / Rapid traverse Z: 30 m/min - Standard fully enclosed cabin with automatic door opening – manual or automatic loading possible Main Spindle - Spindle interface according to DIN 55026: Size A6 - Max. spindle speed: 4,500 rpm - Spindle power at 100%/40% duty cycle: 23/18 kW - Spindle torque at 100%/40% duty cycle: 146/115 Nm Tailstock - Interface: MK4 - Clamping force: 850 daN - Clamping stroke: 200 mm Turret Configuration X1/Z1: Tool Turret with Driven Tools - Tool mounts cylindrical shank to DIN 69880: 8 × VDI 40 - Max. tool length: 130 mm - Number of stations: 8 - Max. turret speed: 4,500 rpm - Max. torque at 10% duty cycle: 27 Nm; at 100%: 14 Nm Turret Configuration X2/Z2: Tool Holder with Driven Tools - X-HOT unit for polygon turning, max. eccentricity (stroke): 8 mm - X-HOT tool holder interface: HSK 32S Electrical Equipment - Operating voltage: 400 V, 100 A - Connected load: 37 kVA Dimensions - Overall dimensions: Length 3,000 mm (6,477 mm with chip conveyor), Width 3,000 mm, Height 3,650 mm - Weight: 11,000 kg Hodpexwmf Ssfx Aknofl Main Features and Capabilities: - Vertical design: Optimum chip disposal, manual or automatic loading/unloading - Control: Siemens 840D for NC1 and NC2 - High precision: Positioning accuracy X/Z axes ±0.002 mm (Heidenhain absolute linear scales) - Powerful main spindle with wide speed range - Driven tools expand application range to include drilling and milling - Tool life monitoring - Chip conveyor coolant: Knoll - Coolant filtration unit up to 40 bar: Knoll FKA/1400 - Part detection system with low air pressure sensor - AUTOMATION INFRASTRUCTURE FOR ROBOT INSTALLED - Fully enclosed work area, work light included - Documentation: Available electronically and as printed manual Machine status: In working condition.

Condition: new, Year of construction: 2026, functionality: fully functional, air demand: 15 m³/h, pressure: 6 bar, compressed air connection: 6 bar, operating pressure: 6 bar, inner dimension width: 2,000 mm, inner dimension height: 650 mm, volume flow: 12,000 m³/h, tank capacity: 2,500 l, air pressure: 6 bar, suction capacity: 12,000 m³/h, New RB-2000 Conveyor Blast System Description: The RB-2000 conveyor blast system from ABRAZIV Kft. was developed for the economical surface treatment of steel sheets, profiles, tubes, and welded structures and is ideally suited for descaling, derusting, cleaning, and roughening steel surfaces. The system is manufactured to order and can be individually configured according to the customer's requirements. With a passage width of 2,000 mm and a workpiece height of up to 650 mm, the RB-2000 is particularly suitable for large and heavy workpieces. It offers maximum flexibility for demanding applications in steel construction, mechanical engineering, tank construction, and the metalworking industry. The RB-2000 is equipped with four high-performance ABR-500 blast turbines. Two turbines are arranged above and two below the conveyor, ensuring optimal coverage of the cross-section and a uniform blasting result. The inner surfaces of the blasting chamber are lined with highly wear-resistant manganese steel. Other areas are protected by wear-resistant rubber, which simultaneously reduces noise levels. A closed blasting media circuit with a screw conveyor, bucket elevator, blasting media cleaning, and dosing system ensures reliable and economical operation. All functions of the system are operated via a central control unit. In addition to automatic operation, a manual mode is also available for maintenance work. Technical Data Passage Passage width: 2,000 mm Min. workpiece length: approx. 1,500 mm Max. workpiece height: 650 mm Blast Turbines Number: 4 Type: ABR-500 Turbine diameter: 500 mm Speed: 2,600 1/min Blasting media flow rate per turbine: 150–300 kg/min Conveyor Hedpfx Akozikaqsnsfl Load capacity: 1,500 kg/m Speed range: 0–4 m/min Power Requirements Base machine: 59–103 kW Cartridge filter: 15 kW Compressed air: min. 6 bar Compressed air consumption (filter): 15 m³/h Other Data Blasting media capacity: 2,500 kg Recommended blasting media grain size: 0.4–1.2 mm Extraction capacity: 12,000 m³/h Mains voltage: 3 × 400 V Control voltage: 230 V Frequency: 50 Hz Optional Frequency inverter Extended conveyors Automatic height scanning Automatic blasting media dosing Special paint finish Transport Assembly Commissioning Operator training Spare parts supply Maintenance and service Application Areas The RB-2000 is particularly suitable for: Steel sheets Steel profiles Tubes Hollow profiles Welded structures Steel construction Mechanical engineering Tank construction Contract blasting operations Location / Manufacturing Lichtenfels (Germany) / Kecskemét (Hungary) As a manufacturer, we develop and produce our conveyor blast systems individually according to customer requirements. In addition to the RB-2000, other sizes and special versions are available. We will be happy to advise you on the design of the appropriate system and provide you with a non-binding offer. Price on request.