Oak threshold sleeper threshold

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: 724, saw blade diameter: 600 mm, table height: 850 mm, positioning accuracy: 0.4 mm, rotational speed (max.): 3,000 rpm, working length: 8,000 mm, TECHNICAL DETAILS Saw blade diameter: 600 mm Motor power: 12.5 HP Saw blade speed: 3,000 rpm Working table height: 850 mm Extraction ports: 3 units, diameter: 100 mm Max. working length: 8,000 mm Positioning accuracy: +/- 0.4 mm Cutting capacities Width 610 mm, height: 30 mm Width 580 mm, height: 60 mm Width 530 mm, height: 100 mm Width 490 mm, height: 120 mm Width 450 mm, height: 140 mm Width 380 mm, height: 160 mm MACHINE DETAILS Drive system of saw unit: hydraulic Ffsdpoyf Evyefx Ac Nou Discharge area: 4,000 x 600 mm Compressed air requirement: 7 bar Dimensions & Weight Overall dimensions of assembled machine (L x W x H): 13,000 x 2,000 x 1,600 mm Transport dimensions (L x W x H): Machine 1,200 x 1,700 x 1,600 mm Transport dimensions (L x W x H): MATRIX pusher 8,800 x 1,500 x 1,500 mm Weight: 1,600 kg EQUIPMENT Feed system with precision rack and pinion and brushless motor Position measurement via magnetic tape Pneumatic lifting of the pusher with workpiece measuring probe Cutting cycle control via keyboard or remote PC Operator software with 99 programmable cutting cycles Operator software with 1 cutting cycle for 100 programmable dimensions Safety cover for cutting area Two-hand operation safety device Discharge flat table

Condition: used, functionality: fully functional, operating hours: 4,189 h, fuel type: diesel, mast type: duplex, FORKLIFT TCM FD25Z1 IZUSU ENGINE DIEZEL SHORT MAST.....START AND DRIVE..... Fjdpfxjt U Ivts Ac Njfu

Condition: ready for operation (used), functionality: fully functional, cutting length (max.): 3,550 mm, cutting width (max.): 530 mm, overall weight: 9,000 kg, stroke length: 100 mm, TECHNICAL DETAILS Usable cutting length (as double guillotine): 3,200 mm Usable cutting length (as single plate shear): 3,550 mm Press stroke: 100 mm Press width: 550 mm Min. cutting width: 18 mm Fedpfxsyf Euce Ac Nefu Max. cutting width: 530 mm Scrap setting range: 0/50 mm Operating pressure: 6/7 bar MACHINE DETAILS Installed total power: 13.9 kW Dimensions & Weight Dimensions (L x W x H): 5,200 x 1,700 x 1,800 mm Weight: 9,000 kg EQUIPMENT Robust steel construction Blade beam made of cast iron Self-lubricating prismatic guides Adjustable rear support Press for holding the veneer package during cutting Photoelectric cells Electronic programming device Perimeter safety guards

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, cutting length (max.): 4,400 mm, cutting width (max.): 4,300 mm, main saw diameter: 350 mm, controller model: G-VISION, Equipment: scorer, TECHNICAL DETAILS Cutting dimensions: 4,400 x 4,300 mm Saw blade projection: 90 mm Saw carriage feed speed: 5 - 100 m/min Pusher feed speed: 125 m/min Pusher return speed: 60 m/min Fedpfx Asyf Epyoc Nsfu Return speed: 100 m/min Main saw blade diameter: 350 mm Main saw motor power: 12.5 HP Scoring saw diameter: 180 mm Scoring saw motor power: 2 HP Extraction port: 200 mm Compressed air: 6.7 bar MACHINE DETAILS Control system: G-VISION Dimensions & Weight Dimensions (L x W x H; installed): 6,400 x 7,500 x 1,800 mm Dimensions (L x W x H; for transport) Machine: 6,500 x 1,500 x 1,800 mm Dimensions (L x W x H; for transport) Pusher: 5,200 x 1,200 x 1,200 mm Total weight: 3,200 kg EQUIPMENT Automatic horizontal panel saw with clamps Frontal stack loading Three front air cushion tables Automatic pusher with lateral and top guides as well as 7 pneumatic clamps Automatic side alignment Automatic saw blade projection adjustment Electronic control of speed and position Easy access to saw carriage Pneumatic quick-change unit for tools Multitasking operating system Microsoft Windows XP/2000/NT Sequential control of cutting patterns Parametric control of feed speed Direct control of machine functions Cutting pattern adjustment

Condition: used, power: 294 kW (399.73 HP), overall weight: 78,000 kg, Year of construction: 1997, operating hours: 11,280 h, machine/vehicle number: 72653, Backhoe excavator with digging bucket, extensive documentation available Fodpet S H A Hofx Ac Nofu

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 60 mm, workpiece length (max.): 3,000 mm, overall weight: 2,700 kg, TECHNICAL DETAILS Working area X-axis: 3,000 mm Working area Y-axis: 1,000 mm Working area Z-axis: 60 mm Maximum workpiece length: 3,000 mm Minimum workpiece length: 90 mm Maximum workpiece width: 1,000 mm Minimum workpiece width: 70 mm Maximum workpiece height: 60 mm Minimum workpiece height: 8 mm Vertical electrospindle power: 4.8 HP Circular saw unit diameter: 150 mm Circular saw unit power: 2.3 HP Vertical drilling spindles: 29 Horizontal drilling spindles (X-axis): 8 Horizontal drilling spindles (Y-axis): 2 MACHINE DETAILS Compressed air: 7/8 bar Ffjdpfoyf Elzsx Ac Nsu Total installed power: 20 kW Machine weight: 2,700 kg EQUIPMENT Numerical control with Biesseworks software Infeed table with motorized belts (left) 2 panel clamps Outfeed table with motorized belts (right) Protection for machining head with emergency stop front mats Transfer system for panel loading and unloading with aluminium profiles Belt-driven table for panel transfer/lifting bar BiesseWorks machining programming system

Condition: ready for operation (used), functionality: fully functional, travel distance X-axis: 3,085 mm, travel distance Y-axis: 1,385 mm, travel distance Z-axis: 180 mm, controller model: Xylog, milling spindle speed (max.): 18,000 rpm, TECHNICAL DETAILS X-axis working area: 3,085 mm Y-axis working area: 1,385 mm Z-axis working area: 180 mm Programmable X-axis speed: 50 m/min Programmable Y-axis speed: 45 m/min Programmable Z-axis speed: 22.5 m/min Drilling unit Vertical spindles: 10 Horizontal spindles X-axis: 2 Ffsdpjyf Ekkofx Ac Neu Horizontal spindles Y-axis: 2 Motor power: 2.2 kW Speed: 4,000 rpm Milling unit Electrospindle: 10 HP Speed: 18,000 rpm Engraving unit Motor power: 2.2 kW Speed: 6,000 rpm Worktable Number of worktables: 6 Vacuum suction cups: 18 Loading supports: 4 Vacuum pump Flow rate: 100 m³/h MACHINE DETAILS Control system: Xylog Installed power: 17/20 kW Compressed air: 6/7 bar Weight: 3,000 kg EQUIPMENT Automatic lubrication

Condition: used, mileage: 226,206 km, power: 235 kW (319.51 HP), first registration: 10/1981, fuel type: diesel, number of seats: 27, gearing type: automatic, color: white, brakes: retarder, Equipment: air conditioning, bathroom, onboard kitchen, parking heater, This SG 221 HDS was originally intended for shuttle service to Southern Europe, but remained a one-off; nevertheless, it served as the foundation for two further high-deckers of a special kind: the S 215 HDS and S 216 HDS, which would soon bring Kässbohrer many new customers. Additionally, this coach introduced the 'S' designation: it stands for Super, because these new high-deckers truly lived up to their name. With a height of 3.63 meters, the elevated passenger compartment created even more space, accommodating not only more luggage (16 cubic meters) but also additional service facilities. Extra fuel tanks could also be installed without issue. Regardless of which of the two Super-Setras the bus operator chose, the engineering marvel of these two new Ulm models was that, except for the front section, they were 100% modular components from the Series 200 and shared identical bolted assemblies with other Setra touring coaches. The 216 HDS offered space for up to 16 rows of seats. In comparison, the underfloor cockpit variant provided more interior space. With the Setra SG 221 HDS, Kässbohrer had a vision, but due to the ban on running articulated touring coaches through France, they shifted focus in favor of solo vehicles. The SG 221 HDS was subsequently used as a demonstration and information bus at trade fairs and conferences; with its generously equipped kitchen on board, it became a central meeting point for representatives and customers. +++ Unique Vehicle +++ +++ATTENTION!!!!!+++ +++pure restoration project+++ +++not roadworthy / only the engine runs+++ Engine: Mercedes-Benz Mileage according to odometer Transmission: 5-speed automatic Seating: 24+2+1 sleeping seats ---- Safety Retarder * Fog lights Passenger compartment Stand heating * Air conditioning * Tables * Curtains * Jet ventilation * Reading lamps * Double glazing Ffjdpfermlp Eox Ac Nju * Footrests * Tap system with bar and large kitchen in rear area * Separate bar area in the center * Lounge area at the front convertible to sleeping area * Refrigerator + additional * Microwave * Rear WC * Driver microphone Exterior Power steering * Tachograph with disc * Sleeping cabin * Driver door * Roof hatches/fans/roof ventilator Other German vehicle documents * Vehicle dimensions: length 18.00m, width 2.50m, height 3.95m * Twin tires * Tires: Front axle approx. 40% Our internal vehicle number: 7271 Subject to errors. Pictures and text may differ from the actual vehicle. Over 180 vehicles always in stock.

Condition: ready for operation (used), functionality: fully functional, overall weight: 5,000 kg, working width: 1,300 mm, workpiece height (max.): 130 mm, TECHNICAL DETAILS Working width: 1,300 mm Maximum working thickness: 130 mm Minimum working thickness: 1 mm Conveyor belt feed speed: 5/25 m/min MACHINE DETAILS Installed power: 32 kW Compressed air: 7 atm Dimensions & Weight Dimensions (L x W x H): 4,400 x 2,500 x 1,600 mm Weight: 5,000 kg EQUIPMENT Ffedpfx Acoyf Eh No Nou Cross belt - Motor: 15 Hp - Electronic speed controller with display Transversal belt - Motor: 15 Hp - Electronic speed controller with display Transversal sanding belt size: 1,350 x 150 mm Chevron belt size: 5,510 x 140 mm Belt blower Fixed table and moving head for inline processing Rotary blower for panel cleaning Vacuum table Belt cleaning brush Infeed roller conveyor Extraction ports: No. 2 diameter 200 mm – No. 2 diameter 150 mm – No. 2 diameter 100 mm

Condition: ready for operation (used), functionality: fully functional, feed rate X-axis: 12 m/min, edge thickness (max.): 10 mm, overall weight: 1,530 kg, rotational speed (max.): 12,000 rpm, tool diameter: 80 mm, TECHNICAL DETAILS Panel height: 1,060 mm Maximum edge thickness: 10 mm Minimum panel length: 140 mm Minimum panel width: 85 mm Feed speed: 12 m/min Sanding Unit Motor power: 2.4 HP Speed: 12,000 rpm Tool diameter: 80 mm Extraction port diameter: 60 mm Gluing Unit Glue pot capacity: 2 kg Glue application roller diameter: 25 mm Pressure roller cutter, large roller diameter: 100 mm Pressure roller cutter, small roller diameter: 80 mm End Trimming Unit Motor power: 1.07 HP Maximum tool diameter: 140 mm Extraction port diameter: 80 mm Milling Unit Motor power: 0.87 HP Tool diameter: 70 mm Extraction port diameter: 80 mm Scraper Unit Extraction port diameter: 60 mm Fsdoyf Ed Ropfx Ac Nofu Joint Scraper Unit Extraction port diameter: 60 mm MACHINE DETAILS Compressed air connection: 7 bar Dimensions & Weight Dimensions (L x W x H): 3,900 x 1,000 x 1,600 mm Weight: 1,530 kg EQUIPMENT Electronic control panel with USB port Sintra software Touch probe devices Vertical and front touch probe devices with rotating discs Removable panel support arm

Condition: excellent (used), Perfectly preserved six-spindle INDEX MS 25 automatic lathe with six transverse and six longitudinal tool guides. The price is negotiable depending on the selected additional equipment: clamping pods, tools, chip conveyor, etc. The machine is still in production. Viewing possible by arrangement. Fjdjqhkukopfx Ac Njfu

Condition: not inspected (used), functionality: unexamined, feed rate X-axis: 30 m/min, edge thickness (max.): 25 mm, overall weight: 3,500 kg, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Edge thickness min: 0.6 mm Edge thickness max: 25 mm Coil material thickness min: 0.3 mm Coil material thickness max: 3 mm Panel height min: 10 mm Panel height max: 60 mm Panel width min: 70 mm Feed speed: 8-30 m/min Extraction port diameter: 120 mm Blade diameter: 140 mm Blade spindle speed: 12,000 rpm Milling unit Milling unit tool diameter: 80 mm Milling unit motor power: 0.75 kW Milling unit spindle speed: 12,000 rpm Chamfering unit Chamfering tool diameter: 80 mm Chamfering motor power: 0.75 kW Chamfering spindle speed: 12,000 rpm Rounding unit Rounding unit motor power: 0.35 kW Rounding unit spindle speed: 12,000 rpm Fedpfoyf Ebvox Ac Nofu Sanding machine Oscillating sanding motor power: 1.5 kW Oscillating sanding speed: 1,400 rpm Brushing unit Brushing unit motor power: 0.3 kW Brushing unit speed: 1,450 rpm Compressed air requirement: 6 bar MACHINE DETAILS Dimensions & weight Dimensions (L x W x H): 8,200 mm x 1,500 mm x 1,650 mm Weight: 3,500 kg EQUIPMENT Fully automatic edge banding machine Sanding unit Processing of wood, veneer, PVC, ABS, and furniture edges CE certification Automatic pressure beam lifting Controlled guidance prior to sanding Group of 2 sanding units Glue pot with pre-melting unit Pneumatic pressure rollers Soundproof safety enclosure Tilting end trimming unit Edge sanding unit Feed speed variator

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 201011RX000004, feed rate X-axis: 20 m/min, workpiece height (max.): 120 mm, edge thickness (max.): 16 mm, overall weight: 2,400 kg, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Panel thickness min./max.: 10 mm / 120 mm Panel length min.: 140 mm Panel width min.: 60 mm Edge thickness: 0.4 mm - 16 mm Variable feed rate: 10-20 m/min Edge height: 120 mm MACHINE DETAILS Installed power: 22 kW Compressed air: 6 bar Dimensions & Weight Dimensions (L x W x H): 6,730 x 1,500 x 1,910 mm Weight: 2,400 kg EQUIPMENT 10.7" color electronic touchscreen control Servo-controlled axis infeed guide Section 2 pre-milling unit - motors 2.2 kW - 6,000 rpm - diamond tools 100 mm x 120 mm x 30 mm Infrared lamp 0-600°C - 600 Watt Cooling anti-adhesive spray system Ffsdpfxeyf D Ubj Ac Nsu Automatic edge feeder Universal gluing station with pre-melter for PUR and EVA adhesives Quick-release glue pot Servo-controlled axis pressure units Roller edge trimming for 3 mm PVC/ABS Glue pot cleaning table End trimming unit with 2 tilting motors, each 0.50 kW - 12,000 rpm Tilting trimming unit with servo-controlled axis - motor 1.1 kW - 12,000 rpm Corner rounding unit with 2 motors - 0.22 kW - 12,000 rpm Pull-off unit with servo-controlled axis Glue scraping unit Buffing unit - 0.18 kW - 1,400 rpm Dryer unit 0-600°C - 4,000 Watt Soundproof enclosure Fixed panel support roller conveyor Extraction: 7 inlets Ø80 mm, 1 inlet Ø120 mm

Condition: good (used), Traypacker / wrap arround packer Trays and wrap-around boxes minimum packaging size L x W x H = 190 x 140 x 80 mm maximum packaging size L x W x H = 460 x 350 x 250 mm 4 lane machine Hotmelt machine was rebuild in 2018 siemens s7 plc controlled easy format change as-is or adjusted to customer needs Fsdofxypijpfx Ac Njfu

Condition: ready for operation (used), Year of construction: 1994, functionality: fully functional, machine/vehicle number: 14219, travel distance X-axis: 1,250 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 560 mm, spindle diameter: 75 mm, spindle speed (max.): 1,800 rpm, With digital readout of travel distances! TECHNICAL DETAILS X-axis: 1,250 mm Y-axis: 900 mm Z-axis (or W-axis): 560 mm Spindle diameter: 75 mm Spindle speeds: 18–1,800 rpm Table size: 950 mm x 950 mm Fedpfx Aeyfhghjc Nofu MACHINE DETAILS Weight: 10,000 kg