Hot water tank

Condition: ready for operation (used), Year of construction: 2004, operating hours: 60,425 h, functionality: fully functional, turning length: 1,050 mm, turning diameter: 465 mm, travel distance X-axis: 300 mm, chuck outer diameter: 325 mm, controller model: Fanuk Series 21I-TB, TECHNICAL DETAILS Max. turning length: 1,050 mm Turning diameter over cross slide: 350 mm Max. turning diameter: 465 mm Chuck diameter: 325 mm X-axis travel: 300 mm Dujdpfx Asy Hg S Hjiwjt Z-axis travel: 1,050 mm Max. spindle speed: 3,500 rpm Max. torque: 630 Nm Spindle bearing diameter: 120 mm Max. bar diameter: 90 mm Tailstock stroke: 850 mm Quill stroke: 150 mm Rapid traverse X/Z axis: 30 m/min Number of tool turret positions: 12 Tool holder: VDI 40 MACHINE DETAILS Control: Fanuk Series 21I-TB Drive power: 33 kW

Condition: ready for operation (used), Year of construction: 2009, operating hours: 9,192 h, travel distance X-axis: 1,200 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 500 mm, controller manufacturer: HEIDENHAIN, controller model: iTNC 530, spindle speed (max.): 16,000 rpm, number of axes: 3, This 3-axis HERMLE C 1200 vertical machining centre was manufactured in 2009. It features an impressive X-axis travel of 1200 mm, Y-axis travel of 900 mm, and Z-axis travel of 500 mm. The machine is equipped with a spindle speed of 16,000 rpm and includes 30 tool stations. If you are looking to get high-quality machining capabilities, consider the HERMLE C 1200 machine we have for sale. Contact us for further details. • X – 1200 mm • Y – 900 mm • Z – 500 mm • Machining Center C 1200 V • Heidenhain iTNC 530 contouring control • Spindle 16,000 rpm • SK 40 • 30 Tool Stations • Rigid Clamping Table • Coolant System • Electronic thermal compensation (iTNC) with temperature sensors on the motor spindle and machine base • Portal design with a closed rear wall for significantly better support during torsional loads • Two axes are located in the tool, providing very good mass distribution and ideal conditions for high rapid traverse and feed rates • Feed screw diameter and pitch (X and Z axes): 40 / 20 mm • Feed screw diameter and pitch (Y axis): 50 / 20 mm • Direct measuring system • Resolution: 0.0001 mm • Position tolerance (Tp) in X-Y-Z axes according to VDI/DGQ 3441: 0.010 mm • Recommended ambient temperature for maintaining accuracy: 20 °C ± 1 °C • Flushing/wash-down system for rinsing the side work area • Display: 15" TFT color flat screen • Flexible contour programming • Part program memory • Tool diameter capacity: 80 mm • Tool diameter with free adjacent slots: 125 mm • Maximum tool length: 300 mm • Maximum tool weight: 8 kg • Maximum magazine load: 120 kg • Chip-to-chip tool change time according to VDI 2852: 6.5 seconds • Manual control unit includes electronic handwheel, axis direction keys, feed control, rapid traverse, emergency stop, and enable switch • Machine on – 11,927 h Dodeylw Stopfx Aiweut • Spindle on – 9,192 h Additional equipment • Chip conveyor • Heidenhain touch probe • Electronic Manual Control Module (iTNC) Technical Specification Taper Size SK 40

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, travel distance X-axis: 800 mm, travel distance Y-axis: 520 mm, travel distance Z-axis: 550 mm, controller model: Heidenhain iTNC 530, spindle speed (max.): 10,000 rpm, The machine spindle was replaced in 2022! TECHNICAL DETAILS Traverse path X-axis: 800 mm Traverse path Y-axis: 520 mm Dsdpfx Aisy E Hqtjweut Traverse path Z-axis: 550 mm Spindle type: SK40 Spindle speed: 10,000 rpm Tool changer: 24-position Table size: 950 x 520 mm MACHINE DETAILS Control system: Heidenhain iTNC 530 Dimensions & Weight Dimensions (LxWxH): approx. 2.60 x 2.60 x 2.70 m Weight: 6,800 kg Operating Hours Machine on-time: approx. 47,000 h Program run time: approx. 5,700 h Spindle: approx. 4,800 h EQUIPMENT IKZ (internal coolant supply) Hexagon probe Note: NC clamps and tool holders are not included in the offer.

Condition: ready for operation (used), Year of construction: 1983, operating hours: 50,000 h, functionality: fully functional, operating pressure: 200 bar, overall weight: 33,000 kg, pressing force: 1,000 t, stroke length: 650 mm, travel speed (max.): 3,600 mm/min, TECHNICAL DETAILS Pressing force: 1,000 t Clamping force of the core plates: 30 t Travel speed: approx. 60 mm/s Operating pressure: 200 bar Stroke of the movable plate: 650 mm Stroke of the mold holder plate (towards operator): 980 mm Heating Plates and Heating System Heating plate size: 1,000 mm x 1,000 mm Number of heating plates: 7 Number of openings: 6 Opening dimension per opening: approx. 108 mm Specific pressure on plates: 100 kg/cm² Hydraulics and Power Units Hydraulic pump power: 9 kW Oil dynamic pump power: 11 kW Installed electrical power: 21.5 kW Hydraulic oil capacity: approx. 160 l Operating Fluids Amount of hydraulic fluid emulsified with water and 5% CIL-SOLIOIL-BK oil: approx. 1,300 l Nitrogen bottles (each 60 l at 200 atm) for accumulator pre-charging: approx. 10 MACHINE DETAILS Weights Weight of the press: 33 t Weight of hydraulic power unit: 0.4 t Weight of pump and accumulator: 1.9 t Dujdpfjy Hhqdsx Aiwst Weight of electrical unit: 0.2 t Total delivery weight: 35.5 t FEATURES Heating system with saturated steam Electrohydraulic power control device Electrovalve air venting system

Condition: new, power: 90 kW (122.37 HP), Year of construction: 2026, A double rotor hammer crusher is a type of crusher in which two rotors are mounted on a single shaft, combined to form a spinning rotor. The double rotor arrangement enhances the crushing capabilities and provides a more efficient and reliable crusher design compared to single rotor crushers. Here are some key features and aspects of a double rotor hammer crusher: 1. Two Rotors: As the name suggests, the crusher has two rotors that rotate in opposite directions on a common shaft. This dual rotor configuration allows for increased impact and crushing power. 2. High Capacity: The dual rotor design enables the crusher to handle larger feed sizes and higher capacity compared to single rotor crushers. It is suitable for crushing materials with high hardness and large sizes. 3. Versatility: Double rotor hammer crushers are versatile and can be used in various applications, including the reduction of limestone, gypsum, coal, and other similar materials in the mining, cement, and building materials industries. 4. Impact Crushing: The primary mechanism of crushing in a double rotor hammer crusher is through the impact of the hammers against the material. The material is fed into the crusher, and the high-speed rotating hammers impact and shatter the particles. 5. Adjustable Gap Settings: These crushers often have adjustable gap settings between the rotors and the impact bars, allowing control over the final particle size. 6. Durability: The robust design of the double rotor hammer crusher makes it durable and capable of handling tough materials and continuous operation. 7. Reduced Wear: The dual rotor arrangement can help distribute wear more evenly across the hammers and other wear parts, potentially extending the overall lifespan of the crusher. Dusdpfx Aioq Nf Enjwot Typical Technical Specifications While exact numbers vary by manufacturer, these are the standard ranges for industrial models: Model (Rotor Size),Max Feed Size,Output Size,Capacity (t/h),Total Motor Power 600 × 400,≤110 mm,≤3 mm,10 – 15,18.5+18.5 kW 800 × 600,≤120 mm,≤3 mm,40 – 50,45+45 kW 800 × 800,≤180 mm,≤3 mm,50 – 60,45+55 kW 1000 × 800,≤180 mm,≤3 mm,70 – 80,75+55 kW 1100 × 1000,≤200 mm,≤3 mm,70 – 100,90+110 kW 1400 × 1200,≤200 mm,≤3 mm,90 – 110,132+160 kW For more details about double stage hammer crusher, or double rotor crusher, welcome to leave us a message, our team will get back to you at the earlist.

Condition: ready for operation (used), Year of construction: 2006, operating hours: 16,093 h, functionality: fully functional, turning length: 1,000 mm, spindle speed (max.): 5,000 rpm, controller model: MITSUBISHI M-720BM (MAPPS 2), counter spindle speed (max.): 5,000 rpm, milling spindle speed (max.): 12,000 rpm, TECHNICAL DETAILS Dodpfx Aijy Eydyjwsut Turning length: 1,000 mm Main Spindle Max. spindle speed: 5,000 rpm Drive power: 22/15 kW Spindle bore: 73 mm Counter Spindle Max. spindle speed: 5,000 rpm Drive power: 22/15 kW Spindle bore: 73 mm Milling spindle speed: 0 - 12,000 rpm Tool holder: Capto C6 Tool stations: 100 positions Hollow clamping device: 67 mm MACHINE DETAILS Control unit: MITSUBISHI M-720BM (MAPPS 2) Operating Hours Operating hours: 26,875 h Spindle hours: 16,093 h EQUIPMENT Y-axis Fully indexable B-axis Chip conveyor, discharge right Standard coolant system Interface for high-pressure coolant system, 70 bar Tool spindle with through-spindle cooling Coolant spray gun Blow air through sub spindle Manual tool presetting on main spindle 3-color signal tower Double foot switch Simultaneous 5-axis machining Automatic power off Tool offset for 5-axis machining Programmable data input Dynamic interchange diameter/radius Stroke check prior to movement

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, clamping force: 2,157 kN, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Clamping force: 220 t Screw diameter: 55 mm + 40 mm Maximum injection volume: 618 cm³ + 251 cm³ MACHINE DETAILS Mounting platen: 960 x 830 mm Duedpfxey Exdxo Aiwot Minimum mold installation height: 320 mm Maximum mold installation height: 730 mm EQUIPMENT EC100/A03 Note: When purchasing multiple items from the same location (see offers below), you will benefit from reduced costs for disassembly and loading.

Condition: excellent (used), Boy 80M Duedpemt Hh Eefx Aiwjt Year 1998 Closing 80 tons Scrow 36 mm Spray weighted 132 g spar distance 41x 35,8

Condition: ready for operation (used), Year of construction: 1998, functionality: fully functional, clamping force: 1,961 kN, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Clamping force: 200 t Tie bar spacing: 560 x 560 mm Screw diameter (first component): 60 mm Screw diameter (second component): 35 mm Shot weight (first component): 566 g Shot weight (second component): 178 g EQUIPMENT Two-component system Kraussmaffei Multinject system Note: When purchasing multiple items from the same location (see listings below), the lower costs for dismantling and loading will be waived. Dodpey Exdlefx Aiwout

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, clamping force: 1,225 kN, controller model: CC100, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Clamping force: 125 t Horizontal cylinder: 35 Vertical cylinder: 18 MACHINE DETAILS Dedpfoy Exc Isx Aiwout Control: CC100 EQUIPMENT 1x hydraulic core pull BAP 1x proportional hydraulic interface for index plate BAP 16x heating zones (HK) 2x magnetic clamping plates for BAP and FAP Note: When purchasing multiple items from the same location (see offers below), you will benefit from the lowest costs for dismantling and loading.

Condition: excellent (used), functionality: fully functional, Werner & Pfleiderer Twin-Screw Extruder ZSK 40 – Excellent Condition For sale is a Werner & Pfleiderer (WP) ZSK 40 co-rotating twin-screw extruder. Technical Specifications: • Machine Type: ZSK 40 • Screw Diameter: 40 mm • Screw Length: 7 barrels × 4 D → approx. 28 L/D • Main Drive: 34.5 kW • Motor Speed: 1,800 rpm • Screw Speed: 40 – 400 rpm • Max. Torque per Screw Shaft: 325 Nm • Heating: Electric, connected load approx. 17 kW • Cooling: Water chiller unit • Temperature Control Zones: 6 zones • Barrel Temperature Sensors: 6 • Material Temperature Sensor: 1 • Material Pressure Sensor: 1 Barrel Configuration: • Feed barrel with liquid injection port • Open barrel with insert and 2 liquid injection ports • Multiple closed barrels with ports for liquid injection or measurement points • Degassing barrel General Features: • Co-rotating, closely intermeshing (self-cleaning) screws • High mixing and dispersing performance thanks to modular mixing and kneading elements • Modular system for screws and barrels • Drive section and process section mounted on stable base frame Fields of Application: • Plastics compounding • Masterbatch • Additive and filler incorporation • Laboratory and pilot plant use • Formulation and product development Condition & Runtime: According to the operating hour counter, the machine has run for less than one year and is therefore in excellent, nearly as-new condition. The screw elements are also as new. Dodpfxsycuuyo Aiweut Options & Customizations: Upon request, we can design and install suitable tooling, such as strand dies, and integrate additional peripherals such as screen changers, pelletizing units, dosing technology, or other customer-specific components. The machine can thus be configured and delivered ready-for-operation according to customer requirements.

Condition: ready for operation (used), Year of construction: 1998, functionality: fully functional, screw diameter: 45 mm, clamping force: 2,000 kN, No reserve price – guaranteed sale to the highest bidder!\n\nTECHNICAL DETAILS\n\nClamping unit: 2,000 kN\n\nScrew diameter unit 1: 45 mm\nScrew diameter unit 2: 45 mm\n\nMax. shot volume unit 1: 226 cm³\nMax. shot volume unit 2: 183 cm³\n\nMACHINE DETAILS\n\nMinimum mould installation size: 250 mm\nMaximum mould installation size: 750 mm\n\nEQUIPMENT\n2-component machine\nTie-bar-less design\n\nNote: When purchasing multiple items from the same location (see offers below), you will benefit from the most favourable disassembly and loading costs for each item. Dedjy Exatepfx Aiwsut

Condition: ready for operation (used), Year of construction: 2005, functionality: fully functional, clamping force: 1,225 kN, screw diameter: 30 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Clamping force: 125 t Dujdsy Exagspfx Aiwot Screw diameter: 30 mm Note: When purchasing multiple items from the same location (see offers below), you will only be charged the lowest applicable costs for dismantling and loading.

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, 1 used steam boiler ----- - mounted on frame - Manufacturer: Bay Kessel - BBS Germany Type: HDK 7000 Capacity approx.: 7,000 kg/h Operating overpressure: 10.0 bar Increased test pressure: 18.5 bar Max. steam temperature: 184.6 °C Water content full approx.: 17,500 l Year of manufacture: 2017 CE marking: CE 0036 Equipped with Weishaupt gas/oil burner WM-GL50/1-A, version ZM-R-NR, gas control line, separate control cabinet, feed water pump, Eco, and existing coarse and fine fittings. Dusdpfjx A Dplex Aiwjt

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, clamping force: 2,942 kN, screw diameter: 70 mm, displacement volume: 1,039 cm³, No minimum price – guaranteed sale to the highest bidder! Engel injection moulding machine including robot! TECHNICAL DETAILS Clamping force: 300 tons Screw diameter: 70 mm Max. shot volume: 1,039 cm³ Duedpfxjy Ew U Aj Aiwjt EQUIPMENT 3x core pulls Robot Note: When purchasing multiple items from the same location (see offers below), the respective lower costs for dismantling and loading will be waived.