Oil-water separator without filter element

Kaeser Aquamat CF38

Year of construction: 2013, condition: good (used), machine/vehicle number: 3063, The cost-effective drainage of condensate for your compressor. The oil is separated from the water with a filter set. The filter set is included in the scope of delivery. The purified water (only in conjunction with the filter set) is approved for discharge into the sewer. Kjdjqmmffspfx Ahgsnb Guarantee and warranty are excluded in this advertisement. Price on request.

Condition: excellent (used), Year of construction: 1997, Indexing table 400 mm hand Kjdpfx Ahoxclfzogonb Set tooling included Table bore 10 - 130 mm Key width from 2 - 32 mm Feed rate 0,5 - 5 M/Min; Table Ø: 690 x 460mm Table load: 2000 Ram adjustment:0 - 425mm Length: 1300mm Width: 1100mm Height: 1400mm Weight: 1800kg

Condition: used, Year of construction: 2006, functionality: fully functional, machine/vehicle number: 06007153/001, total height: 6,050 mm, total width: 3,380 mm, total length: 3,074 mm, load capacity per storage section: 210 kg, construction height: 6,050 mm, input voltage: 400 V, Automated Warehouse Optimization Storage System KARDEX Shuttle XP500 System Type: SHUTTLE-XP-500-3050x864 Control: C2000, with B/W OP2000 display Serial Number: 06007153/001 Year of manufacture: 2006 Total load capacity: 2 x 33,550 kg Load per tray: Medium: 205 kg (evenly distributed) Tray dimensions: 3050 x 864 mm Number of trays: 36 units (more or heavier trays available upon request) Shuttle dimensions (W x D x H): 3380 x 3074 x 6050 mm (Height adjustable to available space) Power supply: 3/N/PE400 V, 11 A, 50/60 Hz, 4.9 kVA This offer is valid as long as the system is unsold Technical details per Shuttle: - Maximum total capacity of the KARDEX Shuttle XP: 2 x 33,500 kg - Maximum tray capacity: 36 trays, Medium: 210 kg each, evenly distributed; more or heavier trays can be ordered. - Tray dimensions: 3050 x 864 mm - Machine dimensions (W x D x H): 3380 x 3074 x 6050 mm - System footprint approx.: 10.39 m² - Storage capacity with 36 trays: approx. 95 m², each tray approx. 2.64 m² - Electronic volume measuring system with 25 mm grid on the display - Access opening with sliding doors for protection of personnel and stored goods - C2000 Control System, with B/W OP2000 display - LED anti-glare lighting above access point - Toothed-belt drive for minimal noise - Toothed-belt drive for fastest order picking - Shelf spacing adjustable in 25 mm increments by configuring support profiles, ideal for high-density storage - Weight management system monitors the load per tray - Includes light pointer Price: On request only by e-mail Price: excluding VAT, including transport and installation Delivery time: from stock Machinehandel De Leeuw BV specializes in used paternoster systems from brands such as Kardex, Hanel / Haenel, Electrolux, Bertello, Megamat, Lista, Denocard, and automated storage systems such as the Kardex Shuttle XP and XPlus systems. Machinehandel De Leeuw BV Oordeelsestraat 7-B Kjdsxq Tbtopfx Ahgsnb 5111 PA Baarle-Nassau The Netherlands

Condition: like new (used), Year of construction: 2015, Workpiece Ø max. 400 mm Workpiece length max. 300 mm Chuck Ø max. 500 mm Swing Ø 520 mm Travel X-axis: 1,110 mm Travel Z-axis: 595 mm Knedjxy Ac Sepfx Ahgsb Main spindle: Power 40 / 100 % duty cycle: 47/34 kW Main spindle: Torque 40 / 100 % duty cycle: 600 Nm Main spindle: Max. speed: 2,850 rpm Control: Fanuc 31i No Y-axis

Condition: excellent (used), Year of construction: 2009, operating hours: 29,000 h, functionality: fully functional, Equipment: documentation/manual, The INDEX C200 – manufactured in 2009 – is a powerful CNC production turning center with a FANUC 31i control, main and counter spindle, and a 65 mm bar capacity. The machine features a high-quality 3-turret design, with turrets 1 and 2 each equipped with X, Z, and Y axes, and turret 3 used for machining on the counter spindle. All three disc turrets are equipped with 10 stations and, with driven tools up to 6,000 rpm, enable highly flexible complete machining. With a portal parts handler, conveyor belt, C-axes on the main and counter spindles, and powerful spindle drives, the machine is particularly suitable for productive series production of complex turned/milled parts. Control: FANUC 31i Design: Machine with 3 tool holders / 3 disc turrets Bar capacity: 65 mm Machine bed: Vertically arranged gray cast iron machine bed Main spindle: Spindle 4 Counter spindle: Spindle 5 with Z-axis Spindles Main spindle Bar capacity: 65 mm Spindle diameter at front bearing: 110 mm Spindle nose: ISO 702/1, Size 140 Cyl. Chuck diameter: 160 mm Power: 25 kW at 100% ED / 33 kW at 40% ED Torque: 112 Nm at 100% ED / 150 Nm at 40% ED Speed: 5,000 rpm C-axis: Resolution 0.001° Counter spindle Bar capacity: 65 mm Spindle diameter at front bearing: 110 mm Spindle nose: ISO 702/1, Size 140 Cyl. Chuck diameter: 160 mm Power: 25 kW at 100% ED / 33 kW at 40% ED Torque: 112 Nm at 100% ED / 150 Nm at 40% ED Speed: 5,000 rpm C-axis: Resolution 0.001° Counter spindle Z-axis: 700 mm travel Rapid traverse Z-axis: 50 m/min Tool holder / Turret Design with 3 disc turrets, each with 10 stations. Tool system with 10 stations: Cylindrical shank DIN 69880 – Ø30 x 55 mm. Tool holder 1 X, Z, Y axes 10 stations X-axis: 110 mm Z-axis: 320 / 550 mm (according to documentation) Y-axis: 100 mm, ±50 mm Driven tools: 6.5 kW / 16 Nm / 6,000 rpm Tool holder 2 X, Z, Y axes 10 stations X-axis: 110 mm Z-axis: 550 mm Y-axis: 100 mm, ±50 mm Driven tools: 6.5 kW / 16 Nm / 6,000 rpm Tool holder 3 X-axis 10 stations Used exclusively for machining on the counter spindle X-axis: 180 mm Driven tools: 6.5 kW / 16 Nm / 6,000 rpm Further technical equipment according to documentation Portal parts handling system with numerically controlled Z-axis Workpiece removal from main or counter spindle to conveyor belt Removal of scrap material from the main spindle into a scrap container Portal parts handler: Traverse speed: 100 m/min Traverse range: 70 mm Workpiece diameter max.: 90 mm Workpiece length max.: 250 mm Scrap length max.: 250 mm Workpiece weight max.: 3.5 kg Hydraulic system: Flow rate: 19 l/min Kjdpjy Tmhzsfx Ahgonb System pressure: 90 bar Hydraulic tank: 40 l Coolant circuit: Flow rate: 19 l/min Coolant unit power: 13 kW Coolant system: Pump output: 80 l/min / 8 bar Tank capacity: 300 l Chip conveyor: Chip discharge height: 1,250 mm

Condition: excellent (used), Year of construction: 2014, turning length: 700 mm, travel distance X-axis: 205 mm, travel distance Z-axis: 700 mm, spindle motor power: 22,000 W, total height: 2,800 mm, total length: 6,000 mm, total width: 3,900 mm, overall weight: 9,800 kg, Complete machining with twin spindel, upper and lower turrets Kitagawa 3 chuck left and right Tool holders with driven tools axial and radial Large jaws cabinet with inserts OGL Gantry loader with ca 10 Kg load capacity Chip conveyor Paper Filtration Pressure Tank Max. turning Ø: 400mm X-Axis: 205mm Z-Axis: 700mm Spindle bore: 62mm Knedpfjyn Em Rsx Ahgob Speedrange: 6000Rpm Spindle power: 22kW Subspindle speeds: 6000Rpm Subspindle bore: 62mm Subspindle power: 15kW ATC / revolver: 16 Speed live tools: 6000Rpm Positions lower revolver:16 Speed live tools: 6000Rpm Power live tools: 7kW Chip conveyor: yes Tool eye: yes Length: 6000mm Width: 3900mm Height: 2800mm Weight: 9800kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 2014, Winmax control system Travel ranges X/Y/Z: 1,067 x 610 x 610 mm Spindle speed: 12,000 rpm Tool magazine for 24 tools, SK 40 Knedjzam E Eepfx Ahgob Internal coolant system Chip conveyor Removable handwheel

Year of construction: 1999, condition: like new (used), functionality: fully functional, Manufacturer: Arthur Klink Year of construction: 1999 Type: horizontal broaching machine Model: RIW 10x1600x400 Weight: 2.700 KG General / technical data: horizontal hydraulic internal broaching machine in mint condition with tool holding system ideal for the use of flat broaching tools. Broaching stroke: 1.600mm Tractive force: 10,000 kg (100kN) Mounting in the drawbridge: Ø 85mm Cylindrical Through-hole in the clamping table: Ø 100mm Workpiece diameter: max. 400mm (due to the machine body of the tool trough) Cutting speed: hydraulically infinitely variable from 1.0 m/min to 9 m/min Return speed: hydraulically infinitely variable from 1 m/min to 24 m/min Space requirement of the machine: (w x d x h) approx. 6,400 mm x 1,450 mm x 1,600 mm (without working area) Power supply: 400Volt 50 HZ Connected load: 9kw Equipment: - the machine has an electric control for the clearing stroke movement with manual operation and automatic sequence - the machine has an integrated coolant system - the machine has a tool holding system for flat broaching tools (no feed) - The broaching carriage with the pulling head holder is equipped with a flat guide on both sides Accessories - 1 universal pulling head for flat shanks from 3mm to max. 25mm wide and a maximum pulling force of 10kN (10,000kg) - Complete machine documentation and CE declaration of conformity Knsdpfx Aer A Hcbohgeb Remarks: The machine is ideal for the production of keyways. Due to the connection with the stable machine bed of the machine and the broaching tool holding system, the machine is particularly suitable for quick and easy use of flat broaching tools. The machine has been used very little and is in mint condition. The machine is available for inspection in our warehouse and is ready for demonstration under power. Our direct contact details and further information about the machine can be found in the attached PDF document

Condition: used, Year of construction: 2006, Technical details: max. wheel diameter: 300 mm max. module: 7 weight of the machine ca.: 15 t table turning speeds: 100 U/min table diameter: 180 mm hob turning speeds: 750 U/min max. hob diameter: 300 cutter length max.: 230 mm Ksdpfjyz Sd Rox Ahgjnb Liebherr LC300 with loading automation Machine including counter holder The machine used to work with emulsion *

Condition: refurbished (used), Year of construction: 2007, Completely overhauled Haas Multigrind HT grinding machine available in Q1/2027. Used for re-sharpening involute milling cutters / beveloid gear milling cutters / cutting rotors / form cutters / industrial knives / circular knives / spur gears / skiving tools / deep-hole drills, and other workpieces / components. Control system: Siemens 840 D X-axis: 650 mm Y-axis: 400 mm Z-axis: 280 mm A-axis (indexing table): 360° SK50 C-axis (rotary table): 270° X3-axis: electrically driven, with tailstock Grinding spindle: HSK80 (conversion to HSK50 possible) Dressing unit Tool changer: 10-position magazine Coolant system: Turbo Separator Extraction system: LTA CO2 extinguishing system Additional accessories available from the factory Software can be supplied customized according to customer requirements Pre-acceptance at the factory, commissioning, training, and final acceptance at the customer's site Knedpfx Ahjx Tr H Negob Financing / lease purchase possible Modifications possible