Path processor

HOMAG 2

Condition: used, Year of construction: 2009, - Edge trimming mills - Gluing unit for EVA hot melt adhesive - Pressure zone Iiodpfx Ajzuyhzjbnef - Cutting unit - Copy milling - Pull blades - Deburring unit Edge banding machine Manufacturer: Homag Type: KAL 330/6/A3/S2 Year of manufacture: 2009 Technical data - Edge trimming mills - Gluing unit for EVA hot melt adhesive - Pressure zone - Cutting unit - Copy milling - Pull blades - Deburring unit Note: The technical data and descriptions are taken from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: as good as new (ex-display), FULL LINE of Double-side Sizing-Milling & Edge Banding. Composed of the following machines: VZ0200A) Gantry-portal Loader (Double pick-up station) "BARGSTEDT" Mod. TBH 500/D/30/12 VZ0200B) 1st Double-side Sizing & Edge Bander "HOMAG" Mod. KFL 525/8/A3/15 Iedpfx Asdt Rgvobneif VZ0200C) In-feeding Rollerway "HOMAG" Mod. TDL 310/30/12 with 90° Turning device (from lenghtwise to crosswise) with double cone system VZ0200D) 2nd Double-side Sizing & Edge Bander "HOMAG" Mod. KFL 526/10/A3/30 VZ0200E) In-feeding Rollerway "HOMAG" Mod. TDL 510/25/12 with 90° Turning device (from crosswise to lenghtwise) with double cone system VZ0200F) Cleaning machine "WANDRES" VZ0200G) Gantry-portal Stacker (Double pick-up station) "BARGSTEDT" Mod. TSP 410/D/25/12

Condition: used, Year of construction: 2009, Edge banding machine with workpiece return system Manufacturer: HOMAG Type: PROFI KAR310/11/A20/S2 Year of manufacture: 2009 Technical data Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding. Iodpfx Abozuyhuensif

Condition: used, Year of construction: 2008, Single-sided edge banding machine Manufacturer: HOMAG Type: Optimat KAL210/6/A20/S2 Year of manufacture: 2008 Single-sided machine for joint milling of straight workpiece edges, edge banding and finishing of various edge materials from rolls or as strips, up to 20 mm edge thickness, in longitudinal and transverse operation. power control PC22 Modern control system based on Windows PC Technical data - Feed rate 18 - 25 m/min. - Feed rate with profile milling cutters FK11 max. 20 m/min. - Workpiece thickness 8 - 60 mm - Edge material strips max. 0.4 - 20 mm - Edge material rolls 0.3 - 3 mm Joint milling unit - 2 motors, each 3 kW, 150 Hz, 9,000 rpm. for joint milling of the workpiece edge before edge banding - electropneumatic control of both motors Gluing unit A20 - 2 rollers Quickmelt hot melt adhesive unit - Temperature control electronically with LED display Magazine for 1 roll, manual - for solid edges, strips and rolls - 1 edge feed - 1 roll holder Pressure zone C - 1 driven pre-pressing roller, diameter 150 mm - 6 after-pressing rollers, diameter 70 mm Trimming unit HL84 / 0.8 kW - 2 motors, each 0.8 kW, 200 Hz, 12,000 rpm. - Motors can be manually swiveled for chamfer trimming Pre-milling unit 1.5 kW - 2 motors arranged one above the other, each 1.5 kW, 200 Hz, 12,000 rpm. Profile milling unit FK11, manual - For processing the edge overhang on the top and bottom edges of the workpiece and for milling the front and rear edges of the workpiece Belt sanding unit KS 10 - for sanding straight and solid wood edges, oscillating, Iiedozux R Ispfx Abnof sanding pressure manually adjustable Profile sanding unit PS 10 - sanding from below, for sanding profiles, sanding pressure manually adjustable Automation package Chamfer / Radius KAL210/6/A20 - Automatic adjustment of the infeed fence - Automatic adjustment of the pressure zone - Pneumatic adjustment from chamfer to straight trimming - Pneumatic adjustment of the trimming motors for flush or overhang trimming - Pneumatic adjustment of the pre-milling unit for flush or overhang milling - Automatic adjustment from chamfer to radius milling during profile milling - Pneumatic adjustment PN10 / FA11 - Electronic height adjustment

Condition: used, Year of construction: 2000, machine/vehicle number: 0-260-06-0228, Foot-operated 1200 x 800 mm Iodpfx Absigadljnjif 80 mm dust extraction port pneumatic connection Cable + plug, 16 A 1 set of operating tools 1 set of feeler rollers

Condition: ready for operation (used), Year of construction: 1999, total height: 1,917 mm, total width: 1,200 mm, product length (max.): 9,295 mm, Edgebander manufactured in 1999. This HOMAG Optimat KL 78/A20/S2 features a panel formatting milling cutter, bevel and rounding milling cutter, groove saw, and edge draw blade. It accommodates workpieces with a thickness range of 8 to 60 mm and has a working height of 950 mm. If you are looking to get high-quality edging capabilities, consider the HOMAG Optimat KL 78/A20/S2 machine we have for sale. Contact us for further details. Iodpjzuhc Hsfx Abneif - Equipment: Panel formatting milling cutter, bevel and rounding milling cutter, groove saw, edge draw blade- Additional Equipment: Bühnen PU melting unit (with dedicated blue control box and temperature controllers)- Work Piece Length: min. 120 mm- Work Piece Width: min. 120 mm- Work Piece Thickness: min. 8 - max. 60 mm- Working Height: 950 mm- Machine Dimensions (from floor plan): Length 9295 mm, Total Height 1917 mm (approx. 2275 mm with open hood / noise enclosure open), Working line width approx. 1200 mm- Space Requirements: Length 9.6 m, Width min. 2.5 m, Height 2.3 m (flaps open)- Voltage: 400 V- Frequency: 50 Hz- Current: 55 A- Recommended Fuse: 63 A- Control Voltage: 24 V- Total Extraction Capacity: approx. 6010 m³/h- Air Speed: 28 m/sec- Compressed Air Consumption: approx. 816 NL/min- Pressure Drop: 200 mm WS- Electrical Connected Load: 32 kW- Extraction Connections: 3x Diameter 120 mm, 2x Diameter 60 mm

Condition: ready for operation (used), Year of construction: 1997, Max. workpiece length: 3600mm, max. workpiece width: 1400mm, length: 8750mm, width: 5250mm. Iiedpfx Ajqvnl Tsbnjf

Condition: excellent (used), UNLOADER (SINGLE-CAGE) - Vacuum system with its pump Isdsd Tyvxjpfx Abneif - Top holding bar deplacement (pivoting) of 180° - Horizontal-longitudinal bars (rocker arms) for the vacuum cups supporting - In-side lifting table, surface with motorized-rollers - Front-side sliding door (or metal grid) to out-feed the stack of the panels - Separated electric and command panel - Out-side rollers way (on ground) to out-feed pile of panels from the Unloader - Out-side motorized rollers table (which brings panels to the Unloader), with also cross motorized conveyor belts (at 90°) - Working capacity (cycles/min): 12-15 - Min/Max panels thickness mm 10 - 40 - Min dimensions of the panels mm 250 x 320 (estimated) - Max dimensions of the panels mm 1200 x 3000 - Total installed motor power KW 11

Condition: excellent (used), Double side - Independent Machine (or 1st and/or 2nd in a line) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Panels thickness (min/max) mm 12 - 40 Working width (min/max) mm 250 / 2500 Numerical Control /Software Power Control 22 / woodCommander Adjustable feeding speed (m/min) 15 - 35 Safety and sound-proof enclosures/cabins Distance (center-axes) of the Disappearing Dogs (mm) 1000 SIZING PART (for each side): Spraying unit (Anti-sticking liquid) Anti-chipping Milling Unit (1 x Kw 4,5) Hogging Units KD 11 (2 x Kw 6,6) EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt + Quick Melt Unit) A3 Pressure zone A Edge coils supporting unit (No. 2 of reels) with servo-assisted edge feeding Snipping Unit HL86 (2 x Kw 0,22) Iiedpfx Abszrd Rzsnof Rough Trimming Unit BF10 (2 x Kw 0,55) Fine Trimming Unit PF20 (2 x Kw 0,4) FRRE SPACE for Corner Rounding unit ( Contour Trimming) FF 12 (2 x Kw 0,4) Profile Scraping unit PN 10 Finish processing unit (Glue scraper + Buffing unit) FA 11 Spraying Unit (for polishing liquid)

Condition: used, Year of construction: 2002, functionality: fully functional, HOMAG Optimat KL79 A20/S2 (2002) – Full Configuration The edge banding line is in satisfactory working condition, fully operational and ready for production. Installed Units: • A20/S2 gluing station (edge thickness up to 20 mm) • Edge feed magazine • Front/rear end trimming units (two saw modules) • Top and bottom trimming units • Corner rounding units (two heads) • Profile scraper units (top/bottom) • Glue joint scraper • Buffing/polishing units • Pneumatic control and vacuum extraction system Technical Data (from manufacturer specifications): Ijdjycg D Tepfx Abnjif • Feed speed: 18–24 m/min • Edge thickness: 0.3–20 mm • Workpiece thickness: 12–60 mm • Minimum workpiece width: 55 mm (22 mm thickness) / 100 mm (60 mm thickness) • Machine length: 10,115 mm • Weight: ~6,200 kg • Power supply: 400 V, 50/60 Hz • Compressed air: 8 bar

Condition: excellent (used), LINE (half line) of Double-side Sizing-Milling & Edge Banding, with automatic handling system. Composed of the following machines: A) LOADER (Portal) with double station "RBO" Mod. Advantage C 3200 and central motorized rollers table. B) Infeeding Rollerway, with double-cone TURNING Device "RBO" Mod. GPK-1 C) Double-side SIZING and EDGE BANDING machine "BIESSE" Mod. Stream SB2 11.0 D) UPSIDE DOWN 180° TURNING MACHINE "RBO" Mod. Ribaltatore E) Outfeeding Rollerway, with double-cone TURNING Device "RBO" Mod. GPK-2 F) STACKER (Portal) with double station "RBO" Mod. Advantage SC 3200, with central motorized rollers table. Iodjhvah Nepfx Abnjif

Condition: used, functionality: unexamined, Ferwood Code: RU0010995 - Manufacturer Code: 2-056-16-6201 - Condition: Used - Functionality: Not tested - Compatible Machine: CNC HOMAG - If interested, we offer a refurbishment service; please contact us. Iiodpfxezmidvo Abnjf

Condition: used, functionality: unexamined, Ferwood Code: AGG0215 - Manufacturer Code: 2-017-95-5550 - Condition: Used - Functionality: Not tested - Compatible Machine: CNC HOMAG - WEEKE - If interested, we offer a reconditioning service; please contact us. Ijdpfx Abezmht Asnsif

Condition: excellent (used), Electronic programmer RT 483 No. 2 Through- feed motorized conveyoring belts Feeding speed (55 m/min ca.) No. 2 Horizontal units/supports No. 1 Drilling heads for each horizontal unit/support (1 x HP 1,5) No. 20 Spindles for each horizontal drilling head Max. working width (mm) 3200 Min. working width (mm) 220 Isdpfx Abefz Nanenoif No. 7 Bottom vertical units/supports No. 2 Drilling heads/blocks for each bottom vertical unit (2 x HP 1,8) No. 4 Top vertical units/supports No. 2 Drilling heads/blocks for each bottom vertical unit (2 x HP 1,8) No. 4 Vertical top pressure clamps No. 2 Motorized endless screws to evacuate wastes/chips Quota (axes) digital display Total power installed (Kw) 35,1 The CNC controls the movement (X axe) of the mobile horizontal unit The CNC controls the movement (Y axe) of the stops

Condition: used, functionality: unexamined, Ferwood Code: AGG0122 - Manufacturer Code: 2-056-16-3660 - Condition: Used - Functionality: Not tested - Compatible Machine: CNC HOMAG - WEEKE - If interested, we offer an overhaul service; please contact us. Iiedszmhr Espfx Abnef