Air classifier - hard material separator

Hazemag HA 1412 UL

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. Hodpfx Ahevwlqqj Neng New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2024, condition: new, Overview - of the different variants *Not every position is required: Hsdpfx Aeff Sbieh Nsng Optional: -Bale shredder MHB from 24.990 € net -MHZ straw mill from € 7,980 net -Special hopper 970 € net -Cyclone from € 3,750 net -Sheet metal silo demonstrator with discharge (only sketched in the picture) *optional, if you want to load with the wheel loader Unit price net from € 14,750 - Demonstrator -Dedusting auger - length approx. 4 m 4 sieves are mounted on the underside, which are extracted. Unit price net from: 9.750 € - Extraction parts / hoses flat rate 945 € net - Complete control system Net unit price: € 2,750 -Demonstrator extraction unit MMJET 160 Demonstrator, with cleaning Connection 160, fan 2,2kw air capacity 1850m³ /400 V Automatic compressed air cleaning Unit price net from: 6.950 € -Baler B 400 Bales approx. 400x400x800 (height adjustable) Up to 30 bales per hour with + - 20 kg from 59.995 € net *A reference system (baler) is located in zip code: 64579 Gernsheim Technical data: Bale size (WxDxH): 400 x 400 x 800 (height can be adjusted on request) Bale weight +/- 20 KG (depending on material) Capacity: approx. 30 bales per hour Storage container approx. 0.7m³ capacity Filling level sensors for min./max. filling level in the container Hydraulic pre-compressor Hydraulic compression ram Hydraulic unit, valve block with oil tank Pump 18.5 KW / 50 liters Rollers in the bale chamber for easy bale push-off Dimensions (l x w x h) 3105x2830x2455 mm Weight approx. 1500 KG mütek baling presses / wrapping machines are designed for the production of bales from a wide variety of materials such as shredded micanthus or elephant grass, wood chips, sawdust and shredded straw. straw. The machine is characterized by a robust design that guarantees consistent quality in continuous operation. quality in continuous operation. The baler compacts the material filled into the storage container without the addition of binding agents and packs the material into plastic bags. The volume of the material can be considerably with the baling press. The volume reduction rate depends on the material. The maximum material moisture content must not exceed 18 % Atro. The container of the mütek baler can be fed automatically or manually and has a volume of approx. 0.7 m³. volume of approx. 0.7 m³. Containers with a larger volume or with an attached suction and filter system as a complete disposal unit are also available. In addition to automatic filling via deduster, mütek also offers filling by means of screw conveyors. With both variants, automatic automatic dedusting is possible. mütek baling presses are equipped with a control cabinet for the control system. In the standard version, the dimensions of the bales (width x depth x height) are 400 x 400 x 800 mm. However, the height can be adapted to your requirements on request. The following advantages arise in the production of bales: - simple and safe storage - No loose dust - Minimization of the storage volume - Low transport volume *Requirements for source material: - dry (max. 30 % ATRO) - Maximum length 35 mm

Year of construction: 2024, condition: new, ZIGZAG air separators Application description: ZIGZAG type air separator is a device designed to purify materials in the waste recycling process. The separator separates light fractions from heavy fractions by pneumatic method. It works well with a wide range of waste materials of 0-150mm size. Air separators of this type are used for pre-ground, jagged or very fine materials. Thanks to our unique design, the separator has the ability to adjust at many points that are important for the purity of the received fractions. ZIGZAG type separators are used in many areas: weight classification of metal granules purification of shredded scrap from the light fraction (films, plastics, paper) Hedoua D Alopfx Ah Neng removal of volatile fraction during recycling of WEEE purification of plastics, rubber purification of municipal waste, glass removal of dust Construction description: The ZIGZAG separator consists of individual components mounted on a common support structure. In the first part, the ZIGZAG module is installed. The module has an inspection hole and regulation of the material stream passage gap. In the second part there is a cyclone discharging the light fraction. Underneath the cyclone there is a variable speed sluice for ejection of separated materials. A fan with electronic speed control is located on top of the structure. The structure is designed in part for loading and unloading by conveyor belts. The separator has a control cabinet equipped with a safety system.

Condition: good (used), Year of construction: 1996, Weinig Unimat 23 four-side planer Hnjdpeh Dwl Defx Ah Nog - German production - grooved top - year of production 1996 - pulling rollers in the table top TECHNICAL PARAMETERS: planed width 230 mm planing height 160 mm grooved top spindle diameter 40 mm 1 lower spindle 7.5 kW 2 right spindle 7.5 kW 3 left spindle 7.5 kW 4 upper spindle 11 kW 5 lower spindle 7.5 kW feed smoothly adjustable 6-36 m / min 5.5 kW feed motor power six top steel pulling rollers two upper rubber pulling rollers three pullers in the table top pneumatic feed pressure pneumatic shoe clamp spindles with brakes pre-table length 1970 mm electric height adjustment central lubrication (split) diameter of nozzles 140 mm dimensions of the machine (length / width / height) 410/200/180 cm weight ~ 3000 kg

Condition: good (used), Technical specifications: Working length: 2100 mm Max. bending capacity: 10.0 mm Pre-bending: 8.0 mm Top roller diameter: 200 mm Bottom roller diameter: 180 mm Number of driven rollers: 3 Hydraulic folding bearing Conical bending device Extended rollers for profile bending Control panel with digital display Hnedpfx Ahswchn Uo Njg Motor power: 5.5 kW CE mark Dimensions (length x width x height): approx. 3100 x 1150 x 1250 mm Weight: approx. 4 tons Accessories: Several roller sets for pipe and profile rolling The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: as good as new (ex-display), Year of construction: 2026, The BTS-MF450HD special waste baler is the ideal baler for compacting difficult materials such as PET bottles, food cans and metal containers, big bags, plastic canisters and plastic packaging, but also scrap tyres and car bumpers can be reduced to a minimum of volume with the baler. The special baling press impresses with its ease of use, safe operation and its spacious filling chamber, it is ideal for medium to large amounts of material. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Hnedpfxevug Dyo Ah Njg Pressing force: 30 Ton Bale weight: up to 450 kg (material depending) Bale size: 1000 H (var.) x 1200 W x 800 D mm Machine size: 3343 H x 1781 W x 1196 D mm Machine weight: 1600 kg Transport height: 2300 mm Loading aperture: 1200 W x 680 H mm Cycle times: 40 seconds Motor: 5.5 kW 16 Amp Power supply: 380 - 400 V (3 phase) Noise level: 68 dB Extra-long dual cylinders for even and early compaction of the material User-friendly lever control Bale kicker for easy eject the bales Extra retainer for reducing the material spring back Reel holder for 4 rolls of strapping A quality product “Made in Europe” Suitable for compacting PET bottles Food cans and sheet metal containers Canisters and plastic containers / packaging Scrap tyres and car bumpers Big bags Cardboard and plastic film / foils Other difficult valuable materials Optional extras Machine colour RAL PLC auto compaction cycles with bale full light and E-stop with locking key Sliding top door Strapping rolls / bale wire Motor 11 kW 32 Amp Demo-Video shows BTS-MF550HD Special Waste Baler. Can Baler, Can Waste Baler, PET Baler, PET Compactor, Tyre Baler, Tire Baler, Scrap Tyre Baler, Scrap Tire Baler, Tyre Compactor, Tire Compactor, Can Baler, Waste Baler, Waste Compactor, Cardboard Baler, Film Baler, Foil Baler, Packaging Plastic Film Foil, Bailer, Baling Press, Garbage Press, Trash Compactor, Baling Compactor, Paper Press, Waste Paper Press, Cardboard Press, Cardboard Compactor, Foil Press, Paper Baling Press, Waste Baler, Residual Waste Compactor

Condition: like new (used), Year of construction: 2023, operating hours: 3,000 h, functionality: fully functional, For sale is a mobile Lefort scrap shear. The machine is in very good condition and can be inspected at any time. Hnsdpjx Elyajfx Ah Nsg

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, overall weight: 4,000 kg, input voltage: 380 V, power: 26 kW (35.35 HP), ejection height: 1,000 mm, opening width: 600 mm, rotor length: 1,000 mm, rotary shear 2 shafts - 2 motors 15kw and 12kw - inversion in case of jam - shredding chamber 1100 x 900 - thickness of new knives 30 - 4 tons - large loading hopper - possibility of loading Hnodpoh Diwusfx Ah Neg very versatile and very powerful, can pre-grind organic matter for methanizers, copper cables, lumps, plaster, BA13, D3E, plastics, wood, bumpers, bottles, metals, hollow bodies, etc. use to grind up sick calves at the renderer.

Year of construction: 2022, operating hours: 400 h, condition: as good as new (ex-display), functionality: fully functional, !!!Demonstration machine with low operating hours!!! Model: Lepton 5100 Year of manufacture: 2022 Operating hours: approx. 400 hrs Location: D 84069 Schierling Availability: short notice Equipment: - Base machine Lepton 5100 with screen decks 1 and 2 Screen deck 1 mesh size: 36 mm Screen deck 2 mesh size: 24 mm - Pre-screen deck with large hopper and variable dosing roller - Volume measurement via load - Prepared for air separator - Compressor Hsdpfxert Uvze Ah Nsng - LED lighting package - Radio remote control for all key settings - Diesel-electric drive 80 kW - Axle levelling system - Tandem axle, road approval for 80 km/h - 19,000 kg total weight - Transport dimensions: 11.97 m total length, 3.98 m height, 2.53 m width, no special transport permit required Possible screening materials: Compost, green waste, biomass, root wood, waste wood, municipal waste, RDF, various recyclables (not suitable for construction rubble or excavated material) Miscellaneous: Very good used condition, fully operational

Condition: excellent (used), functionality: fully functional, machine/vehicle number: 92 880 13, opening: approx. 1.030 x 720 mm Hnedpfjlhrufex Ah Neg rotor-Ø x –width: 1.000 x 1.000 mm weight: approx. 13 t.