Working platform semitrailer

ES-GE 4-Achs-Ballastauflieger

Condition: new, overall weight: 66,500 kg, maximum load weight: 56,590 kg, axle configuration: > 3 axles, total width: 2,550 mm, Equipment: ABS, More vehicles available at Extract from specification. Full specification available on request. Chassis Chassis frame constructed from welded longitudinal members and through-bolted cross-members * Underrun bumper approx. 700 mm wide * Fifth wheel plate at least approx. 8 mm thick, mounted between the main beams * Cross-member spacing max. 400 mm (for longitudinally laid floor) * 3.5 inch king pin to SAE standard, replaceable * Outer frame as UNP 200, open to the outside Landing Gears * 24 t telescopic landing gear JOST - MODUL CH (Heavy Duty), S-foot Axles * 4 x 10 t SAF axles with large drum brakes * 22.5 inch single tyres * Axle spacing approx. 1,700/1,810/1,810 mm * Air suspension units each rated at 10 t capacity * Lift and lower system with 1 rotary slide valve Knorr/Wabco * Bracket for lift and lower device, bolted design Brakes * Smartboard/TIM/Info center on mount for lifting and lowering, in addition to lift/lower valve, without battery (operable only with tractor unit) * Holder for lighting and brake system at the front of underrun bumper, total height approx. 700 mm * Basic tyre pressure monitoring system, connected to EBS CAN-bus * With double release valve for brake and spring chamber * Test nipple for brake cylinder pressure at front right brake cylinder * 1 each red and yellow coupling head * Lift and lower control fitted to left rear side (in direction of travel) * EBS braking system make: Wabco * EBS diagnosis via CAN-bus (EBS socket), no diagnostic cable routed to outside! Tyres * 8 x 445/65 R 22.5 - branded make of our choice * Hub centring Lubrication Lubrication nipple strips on bogies and at the steering front * No central lubrication Bodywork * Without body certificate to DIN EN 12642 XL * 2x LED work lights mounted on top of front bulkhead (facing rear), switch on lift/lower holder * Heavy-duty front bulkhead suitable for platform * Contour markings: yellow sides, yellow rear * Front bulkhead approx. 800 mm high, with sheet metal cladding, bolted design Lighting system Dcsdpfexfx Rvex Af Isn Work lights: 2x LED integrated in lamp panel, operated via reverse gear * 2x LED work lights, switched via reverse, one per side near landing gear * 2x LED reversing lights, one per side in front of the 1st axle * Lighting/electrical system make of our choice * Number plate illumination * The towing vehicle must provide sufficient power for the selected lighting (especially reversing light) * Position lights front, lower, one right and one left, white (LED) * 24 volt lighting system with large multifunction light * Flashing side marker lights (LED) * 1x 15-pin and 2x 7-pin sockets at the front via multifunction box * EBS socket * 1 pair of lane departure marker lights (LED) Floor * Hardwood floor approx. 28 mm thick, alternating with galvanized omega steel profiles Accessories * Vehicle swing-out sticker at the rear * Rear marking plate (ECE) as per our choice * Aluminium underrun protection * Folding and extendable rear right access ladder (without platform) * 2 wheel chocks with holders on front bulkhead * 2 rubber buffer stops at rear corners Mudguards * Rear mud flaps with ES-GE advertising * 180-degree plastic mudguards over each axle * 4 pairs of antispray mud flaps for single tyre configuration Paint/Coating * Chassis painted RAL 1007 daffodil yellow * Front bulkhead (steel construction) in RAL 1007 na