SAND WASHER

DERNASEER D095

Condition: excellent (used), functionality: fully functional, mileage: 180,264 km, fuel type: diesel, color: yellow, empty load weight: 23,500 kg, axle configuration: 2 axles, number of seats: 2, first registration: 07/1998, next inspection (TÜV): 07/2026, Year of construction: 1998, operating hours: 18,712 h, For sale: Liebherr 1030-2 truck crane with a lifting capacity of 30 tonnes. Hodpfx Asxava Rjhvoi Technical condition: fully operational. The crane was overhauled in 2025. Details to be discussed during on-site inspection. The crane holds a valid technical inspection until 23/07/2026 and a current UDT operational permit valid until 31/07/2026. The vehicle has a valid third-party liability insurance policy. The vehicle is registered in Poland. The crane has been operated by the current owner since 2014. Purchase directly from the actual user! We are not intermediaries or traders. On-site inspection and machine testing possible at the facility in Brodnica (87-300), Poland. The machine is ready for work.

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment Hedpfxewu Tu Dj Ahvsi WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: used, Year of construction: 2014, power capacity 3 kW feed pressure 7 bar liter capacity / l weight 286 kg Chicago Pneumatic CPVR15 CE screw compressor - Year of manufacture 2014 The CPVR15 CE impresses with its robust design, long service life and low operating costs. Whether in workshops, workshops or industrial applications - this compressor reliably supplies you with the compressed air you need. Drive power: 3 kW Delivery pressure: 7 bar Air output: up to 58 CFM (approx. 1,640 l/min) at 7 bar Weight: 286 kg Dimensions: approx. 965 mm (L) × 620 mm (W) × 1,040 mm (H) Operating noise: approx. 50-58 dB(A) Voltage/frequency: 415 V / 50 Hz Application: Workshops, craft businesses, industrial applications with medium compressed air requirements Hsdpfx Aoh A Sfdohvoi Included in delivery: 1x compressor - Chicago Pneumatic CPVR15 CE 1x refrigeration dryer - OMI ESD 108 - 0.70kW 1x Beko Öwamat 2 - oil-water separator Technical data was taken from publicly available sources

Condition: repair required (used), Year of construction: 2013, operating hours: 33,439 h, - Volvo L180G - Year of production 2013 - Mileage 33,439 Mtg Hjdpju Ef Hrsfx Ahvoi - Transmission after major overhaul - 340 mtg. - Engine compartment burnt out - condition shown in photos

Condition: good (used), functionality: fully functional, We offer for sale a complete line for multi-point automatic welding of SCHLATTER brand steel wires. Hedpfstvpilex Ahvsi We have three fully operational production lines. There are also automatic machines for the production of transverse wires (so called slitting machines with a cutter). We also have a number of single point welding machines for steel wires.

Condition: excellent (used), Line for door jambs (frames), with END-CUTTING, ROUTERING for COUNTER-PLATE and HINGE INSERTION (Anuba). Composed of: X10030A) Loading Conveyor X10030B) Transfer Conveyor X10030C) Double-end cutting and drilling machine "AMS" - Left-side Cutting 45° - Drilling - Cutting 90° - Right-side Cutting 45° - Drilling X10030D) Angular Conveyor (90°) Hodpfeqwyclsx Ahvoi X10030E) Anuba Inserting Machine "MASTERWOOD" Mod. MULTITEC X10030F) Strike Plate Routering Machine "MASTERWOOD" Mod. Teknomat 3000

Condition: good (used), WEBER tube extrusion line including: WEBER DS 8.5 Elmepla saw Battenfeld R200/6 Battenfeld V125 Hodpfx Ahovryhyjvji

Condition: ready for operation (used), Year of construction: 2002, Speed: 4500rpm, max. bowl diameter: 300mm/167mm, solids: 2.6kg/dm³, material temperature min./max.: 5°C/100°C, bowl dimensions X/Y: 300mm/1200mm, machine material: stainless steel, operating hours: 62293h. Including spare parts. On-site inspection is possible. Hjdpfx Aheu Av H Dsvsi

Year of construction: 1977, condition: refurbished (used), I sell the double mitre saw Rapid DGS, year 1977. Tilting heads Drilling front heads on each side included Hedpfx Aod N Rb Dohvoi Very good condition. Available immediately.

Condition: excellent (used), Year of construction: 2003, working width: 215 mm, welding power (max.): 750 kVA, Complete Mesh welding/Lattice girder factory Factory consists : - Mesh welding line SCHLATTER PG 24 , Semi- automatic , Year - 2002 - Lattice Girder Line SMEI , Full automatic , Year - 2003 - Straightening and cutting machines 1x Wafios R4 2 x VITARI NR16 1X VITARI NR10 Hedpfjqy Ek Ajx Ahvoi - Cold drawing line SMEI , Input wire max.10mm, Speed - 4m/sec. - But welding achine SMEI - Wire sharpener SMEI