Pallet strapping and film wrapping line

Cyklob XZE-3111- GL 2020 pallet conveyin

Year of construction: 2001, condition: good (used), Build in :2001 (Cyklop XZE-311-22), 2001 (Cyklop GL 2000) Description/configuration: Complete line for automatic pallet strapping (double or cross), automatic stretch-wrapping of pallets. Includes fully automated pallet conveying. Complete line with multiple infeed positions, configured as follows: > infeed conveyor with fenders (bump protection), motorized, l~1500 mm, REF 25643.02 > roller conveyor (buffer), motorized, l~1500 mm, REF 25643.02 > chain transfer conveyor, motorized, l~3700 mm, REF 25463.03 > roller conveyor (buffer), motorized, l~1500 mm, REF 25643.04 > roller conveyor (buffer), motorized, l~1500 mm, REF 25643.05 > roller conveyor, with fenders (bump protection),motorized, l~1500 mm, REF 25643.06 > roller conveyor (buffer), motorized, l~1500 mm, REF 25643.07 > roller conveyor (buffer), motorized, l~1500 mm, REF 25643.08 > chain transfer conveyor, motorized, l~3000 mm, REF 25463.09 > chain transfer conveyor, motorized, l~3000 mm, REF 25463.10 > roller conveyor (buffer), motorized, l~1800 mm, REF 25643.11 > pallet strapper Cyklop XZE, REF 25643.30 > roller conveyor (buffer), motorized, l~1500 mm, REF 25643.12 > roller conveyor underneath wrapper, motorized, with pallet lifting device, l~2100 mm, REF 25643.13 > pallet film wrapper GL 2000 ring style, REF 25463.40 > roller conveyor (buffer), motorized, l~1500 mm, REF 25643.14 > roller conveyor (buffer), motorized, l~1500 mm, REF 25643.15 > 90° turntable conveyor, motorized, l~1800 mm, REF 25643.16 > roller conveyor (buffer), motorized, l~1500 mm, REF 25643.17 > pick-up position for strapped & wrapped pallets, with fenders (bump protection), motorized, l~1500 mm, REF 25643.17 max speed in pallets/h: 50 pallets/h Roller conveyor, Chain conveyor (transfer conveyors) Pallet width of up to 800 mm Pallet length of up to 1200 mm max height full pallet (max passage height): ~2000 mm max weight full pallet: 1500 kg Over all length equipment: ~16000 mm Over all width equipment: ~9000 mm Over all height equipment: ~4200 mm Voltage: 400 V, 3 Ph, 50 Hz Air requirement: 6 bar Equipment at central warehouse Helmstedt with nearest airports: Hannover (~1 hrs), Berlin (~2 hrs) Ijdpfx Agshtmp Ts Ijat

Condition: excellent (used), Year of construction: 2017, Available: 2 pieces! condition to check Possibility to buy the high-lift order picker with a set of brand new batteries with a 2-year warranty for 3,500 euros or for 3,000 euros with used batteries Year of production 2017 Load capacity 215 kg Lifting height 3000 mm Travel speed 8 km/h Total length 1528 mm Battery voltage 24V Model EKM-202 Negotiable with larger quantities, big discounts! The agile and versatile EKM order picker is ideal for use in stores, for light maintenance work or order picking without a pallet. Iaodpfx Agjvday Ho Ist The stable mast allows you to lift items up to the third level of the rack - this is the best alternative to a traditional ladder. Automatically closing doors ensure operator safety even at high lifting heights. A sensor mat on the floor increases mobility in the driver's cabin, so the operator can freely choose his position on the standing platform. The spaciously designed workspace guarantees the operator greater comfort while driving and standing sideways. Good visibility in the direction of travel is provided. Ergonomically positioned controls allow simultaneous lifting and steering, which makes working with the EKM very efficient.

Year of construction: 2001, condition: ready for operation (used), A paving stone production line Omag, which has been continuously optimized and upgraded to the latest technical standards, is available. Overhauls: 1) Conversion for an additional hydraulic unit for additional load in 2020. 2) Conversion to servo-vibration with Siemens S7 control in 2016. 3) Conversion to digital path measurement of mould and ram in 2017. 4) New core filling carriages in 2017. Plant components: 1) Board destacker and board stacker including roller conveyor. 2) Board feeder (advance) and board conveyor (scraper) to the lifting frame. 3) Board turner. 4) Horizontal and vertical bundling units Ridder & Signode, years of manufacture: 1994 and 1983. 5) Trafo lifting platform including motors and without control, year of manufacture: 1983. 6) Doppler including hydraulic unit, year of manufacture: 2004. 7) Stone packer Omag K1400 including hydraulic unit, year of manufacture: 1997. The line has no base boards. 8) Stone finisher Omag S22 140-90, year of manufacture: 2001. Documentation available. An on-site inspection is possible. Iodpfxjw R Uzis Ag Ieat

Condition: new, Year of construction: 2026, Drilling and milling machine Kudu with CNC control and tool changer (3-axis) drilling and milling machine with movable processing unit - the table remains stationary, the drill head moves. The drilling machine can be used both manually and fully automatically. After each drilling process, the processing unit moves to the next drilling position fully automatically in the X and Y axes. Operation is kept very simple. The data can be transferred to the machine control using the file formats DXF./DWG. be carried out via a programming station. Alternatively, the system can also be programmed directly on the machine control. The system is very robust and consists of proven machine components. Technical data: • Measuring length: 6,000 mm • Total length: 8,050 mm • Stable machine base • Drilling head speed: up to 2500 rpm (standard version), is supplied with the right speed for your application. • Tool holder: SK 40 • Drive of the X, Y and Z-axes via servomotors • Rapid traverse in the X-axis: 20 m/min • Rapid traverse in the Y-axis: 5 m/min • Distance from upper edge of table to lower edge of tool holder 400 mm • Table width 480 mm • Working height: 1050 mm • Drilling diameter: 3 to 30 mm in St. 50 (depending on the tool) • Tapping: M4 - M30 (with compensating chuck) • Machining path in the Y axis: 300 mm • Tolerance in the X axis: + - 0.1 mm • Tolerance in the Y-axis: 0.06 mm • Tolerance in the Z-axis: 0.06 mm • Drill head drive motor: 5.5 kW • System weight: 2300 kg • System dimensions: 8050 mm x 3000 mm x 2388 mm (see layout plan) • Power connection: 32 A • Air connection: 8 bar • Protection of the system at the front via light barrier • Access protection at the rear, machine fence • Control touch screen panel 21.5", reinforced front glass • Easy programming on the Machine • Milling of long holes and circles • Lubrication takes place using a minimum quantity spray system • without material vices • Remote maintenance possible using Teamviewer (LAN interface) • Tool memory for drilling tools, with dimensions, speed • Simulation of work processes • Digital hand wheel Iodpfefu Ivzex Ag Isat Your advantages • The surface of the workpieces is protected • Clear, graphic surface • Machining directly at the end of the workpiece is not difficult • 50% space saving compared to pushing machining • Chips are collected in the chip tray • Simplest programming & operation • Minimum quantity spray system (standard) • Programming errors are prevented by CAD /CAM excluded

Condition: used, Aufspannplatte - Tisch einer Langhobelmaschine - Tischbreite/Aufspannbreite: 1845 Tischlaenge/Aufspannlaenge: 5505 mm Isdpfx Aobn Amfsg Isat 7 T-Nuten laengs fuer T-Nutensteine: M 30 T-Nutenabstaende zueinander: 263 mm Gesamtlaenge: 6230 mm Plattenhoehe insgesamt: 350 mm Gewicht: 11 t

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Iajdpsvf E Avefx Ag Iot Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: excellent (used), functionality: fully functional, Year of construction: 2019, 1 Used Concrete Batching Plant In excellent condition! Manufacturer: EUROMECC Model: EURO 5 MIX Year of manufacture: 2019 Theoretical capacity: approx. 60–75 m³/h Total production to date: approx. 95,000 m³ Aggregate storage in high silo / inline silo (reihensilo) • Capacity: 5 bins – each 45 m³ • 4 load cells (each 5,000 kg capacity) • Silo loading via feed conveyor belt • Truck feed via loading hopper (25 m³ volume) Complete plant with winter enclosure / insulation Mixers • 1x Planetary mixers with agitators • Type EUROMECC MEP 3000/2000 Dosing system • Aggregates: Weighing belt • Water dosing: 1 water scale 500 kg per scale • Admixture dosing: 1 admixture scale 2x12 liters Iaodpfjxn A Nbox Ag Ist • Cement dosing: 1 cement scale 1,000 kg per scale Control system • Operator/control container included • Main control system: ElettronData Cement silos – total: 6 units • 2x 150 m³ (Diameter: 4.6 m) • 1x 90 m³ (Diameter: 3.5 m) • 1x 45 m³ (Diameter: 3.5 m) Optional equipment: • Warm air heating system inside container • Chemical admixture storage in container • Rest concrete recycling system (optional) Condition: • The plant is in very good and fully functional condition. • AVAILABLE IMMEDIATELY • Location: Denmark • Price: on request Note: Offer is net ex-works, subject to prior sale. Errors, omissions, and/or misrepresentations excepted. No warranty or guarantee. Sold “as-is”, lying or standing. Any duplication, publication or reuse of this offer – in part or whole – is strictly prohibited.

Year of construction: 2011, condition: good (used), Offer 24370 Sludge filtration system in a sea container + conveyor belt Technical data: - Sludge filter press JUNGHANS with cylinder unit Iaodjt Srkpopfx Ag Iet - Flocculation system - Pumps - Separate conveyor belt for sludge removal, length 8.0 m - Control cabinet with electrical equipment - Water collection tray made of aluminum on the entire container floor - Lighting - Sea container with 4 doors - Space requirement for the container: approx. W 6.0 x H 2.4 x D 2.4 m - Weight: approx. 5000 kg - Space requirement for the conveyor belt: approx. W 8.0 x H 0.8 x D 1.0 m - Weight: approx. 1000 kg

Condition: like new (used), Year of construction: 2000, operating hours: 25,000 h, travel distance X-axis: 10,300 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 1,800 mm, feed rate X-axis: 10 m/min, feed rate Y-axis: 10 m/min, feed rate Z-axis: 10 m/min, position of the milling head: 2.5 x 2.5 °, spindle speed (max.): 3,000 rpm, spindle speed (min.): 60 rpm, table width: 3,300 mm, table length: 12,000 mm, mount diameter: 50 mm, total height: 48,750 mm, total width: 100,000 mm, total length: 212,000 mm, overall weight: 100,000 kg, Duplex milling are two machines located one opposite the other which can work seperately or as single machine, workpiece can be machined with 2 simultaneous spindles. Production increase of up to 50% in relation to conventional solutions, i.e. individual milling machines Improvements in part precision, by managing to do the machining of the part in one single setup, in most of the cases One sole operator can control the DUPLEX milling machines Reduced space and investment requirement comparing with two single machines Fast investment amortization due to the high productivity Duplex solution admits different configurations: single working area, pendulum working areas For machining excavator arms / boom like, CAT, Caterpillar, Komatsu, Hitachi, Hyundai, Doosan, Case, Bobcat, JCB, Kobelco, Liebherr, Kubota, Takeuchi, Volvo X-Axis: 10300mm Y-Axis: 2000mm Z-Axis: 1800mm Table Length: 12000mm Table Width: 3300mm Table load: 100000 Power on spindle: 22/30kW Spindle speeds: 60 - 3000Rpm Spindle Taper: 50ISO/Bt/Mk Iaedpforx Rxtox Ag Ijt Feed rate X-Axis: 10000mm/min. Feed rate Y-Axis: 10000mm/min. Feed rate Z-Axis: 10000mm/min. Millinghead auto-index:2.5 x 2.5° Working hours: 25000H Length: 21200mm Width: 10000mm Height: 4875mm Weight: 100000kg

Year of construction: 1990, condition: ready for operation (used), A complete and automated OMAG paving block production line is available. Components: 1) Drawing plate for Colormix in the hopper. 2) InLine washing system. 3) Drying side Rekers. 4) Handling Rekers. 5) Rekers control system. 6) Rekers fork carriage. 7) Part of the drying chamber racks, as they are load carriers for the building. 8) Board crane as buffer placer and empty boards. 9) Cyklop horizontal strapping. Without strapping and boards. Concrete feed: 2-axis bucket, output with 90x90 paving blocks: 1000-1100/shift, board size: 1000mm/1400mm, max. format size: 1000mm/1400mm. Completely new OMAG control system in 2017. Conversion to proportional valves in 2014. Documentation available. On-site inspection is possible. Isdpfx Agsv Nn Hxs Ieat