Heavy-duty granulator

CONDUX Schneidmühle CS 500/600-IIA

Condition: like new (used), Year of construction: 2023, operating hours: 990 h, functionality: fully functional, type of input current: three-phase, total height: 3,900 mm, input current: 63 A, total length: 9,500 mm, total width: 4,500 mm, power: 15 kW (20.39 HP), Equipment: documentation/manual, Pelletizing plant for a wide range of materials such as wood, miscanthus, agricultural by-products and waste (hay, straw, corn stover, etc.), as well as feedstuffs. Bedpfxsxv Dkce Aa Ejld This is a complete plant built on a base frame, consisting of the following components: - Raw material hopper 4 m³ incl. agitator. This was extended by approx. 3–4 m³ with wooden panels. - Intermediate screw conveyor to hammer mill - Hammer mill 11 kW for size reduction of wood chips or other materials - Inclined mixer for material homogenization, incl. moisture measurement, dosing, and level measurement - Dosing hopper for pressing aids feeds into the inclined mixer - Dosing screw conveyor for optimal material feed into the press (speed-controlled) - Press 15 kW including full indicator, temperature monitoring and discharge chute - Conveyor belt to dedusting screen - Dedusting screen with material discharge at 3 m height The plant is designed so it can be easily expanded with a second 15 kW press. The entire system is centrally operated via Siemens PLC with touch display. All parameters are monitored so that the press will be shut down automatically in the event of a fault. The press can also be operated and monitored remotely from any PC. The chip dryer shown in photo 2 on the wall, including discharge and control system, is also available for purchase. For details, please contact us.

Year of construction: 2003, condition: reconditioned (used), Stock - No. 2651 1 used underwater pelletizing unit, partially overhauled in 2023 Throughput up to approx. 450 kg/h depending on the material, consisting of: Type BKG ( Nordson ) Bedsiyyf Iepfx Aa Eeld Start-up valve with hydraulic station Granulator type A300 including die-plate and cutter bar, drive 4.4 kW by-pass system TVE 1000 ED pellet-dryer drive 4 kW incl. Agglomerate catcher Tempered water system with Water box 200 liters, installed heating capacity 9 kW Water pump 2.2 kW with 15³/h heat exchanger Control unit - NEW Further UWP pelletizing units are available ex workshop in Wuppertal-Germany ( as Gala, BKG Nordson, Econ ) Available from the Wuppertal warehouse: complete compounding, pelletizing extrusion lines, with single-screw or twin-screw extruder.

Year of construction: 1972, condition: used, machine/vehicle number: 51512/72, pression: 75 t throat: 300 mm Bedpfx Aaob Tdqus Eold table size: 620 x 800 mm clearance hole in the die: 225 x 325 mm table adjustment: 175 mm tappet area: 180 x 475 mm tappet adjustment: 80 mm stroke adjustment: 16 - 140 mm number of strokes: 90 /min engine: 380 V, 3 kW space needed: 1700 x 1200 x 2500 mm weight: 3,3 t

Condition: new, Year of construction: 2026, Consisting of large bale breaker Type MHB and straw shredder Type MHZ 1) Bale Breaker MHB: Special price from €22,975 net (lead time approx. 15 weeks) Suitable for round or square bales. Includes frequency converter (FU) – regulates the speed of the chain conveyor. The bales are placed on the chain conveyor, and the milling advance is activated. The milling tines tear the straw from the bale and hurl it into the hopper. Ideally, the combination of bale breaker and straw shredder is recommended here. Technical data – Bale Breaker: Performance: 1–2 bales per hour Up to max. 600 kg per hour (depending on screen size used in the straw mill and kW rating of the straw mill). Without straw mill, the bale breaker can process up to max. 900 kg/h straw. Max. square bale size: 2400 x 1200 x 800 mm (L x W x H) Milling motor: 5.5 kW, 380 Volt Chain conveyor feed: 0.75 kW, 380 Volt Dimensions: 3750 x 1730 x 2460 mm (L x W x H) Weight: 400 kg 2) Straw Shredder MHZ 600 – 11/15 kW; available immediately Special price from €6,995 net Surcharge for even larger straw shredder (18.5 kW): + €3,940 net Technical data, MHZ with special hopper: Motor: 15 kW, 380 Volt electric motor Diameter: 600 mm Hardened cutting knives Screen with interchangeable inserts; selectable perforations (10, 12, 15, 22, 30, 45 mm) With star-delta switch, phase protection, and 8 m power cable, plug-in ready Discharge nozzle: 160 mm Blowing distance approx. 12 m Dimensions: approx. 1600 x 1020 x 1360 mm (L x W x H) Weight: approx. 240 kg --- Optional extras for a surcharge: Feed auger: + €970 net Cyclone (suspension by customer on site; should be no more than 10 m away): + €2,970 net Simple filter: €1,750 net --- Further options: Industrial extraction system (demonstrator): Bsdpsb Nulhofx Aa Eeld + from €9,950 net Optional rotary valve (renders material pressureless): + €5,750 net Control panel: from €1,620 net Special breaker extension 3 m (other sizes on request): + €9,750 net Briquetting press MPP 180 S; little used demonstrator 70 mm briquette – up to max. 100 kg/h from €39,700 net * Larger machines available on request --- Description: muetek bale breakers are designed for breaking up round and square bales of hay and straw. The shredder flanged to the bale breaker shreds straw from all types of cereals, hay, maize, and miscanthus. muetek machines of the MHZ / MHB series are characterized by robust construction and heavy-duty build quality. muetek MHB series bale breakers feature a chain conveyor onto which the straw bale can be placed using a front loader. The support surface is adjustable depending on bale type. The chain conveyor pushes the bale against the milling rotor. The feed speed is adjustable. The milling rotor is equipped with several teeth that tear open the straw bale. The separated straw is discharged. --- The machines are generally suitable for dry input material: - Straw - Hay --- Breaking up hemp bales is possible only with a special breaker (surcharge approx. €9,720 net, depending on configuration). Straw mill is not suitable for hemp processing. Requirements for input material: Max. moisture content 12%

Condition: ready for operation (used), Year of construction: 2008, A SIG Corpoplast blow molding machine is available. Output: 21600 bottles/h, bottle formats: 500ml/750ml/1000ml/1500ml, max. blowing air pressure: 40bar, dimensions X/Y/Z: approx. 7000mm/4300mm/3100mm, weight: approx. 20000kg. Including preform feeder Transver AG, year of construction: 2008, silo, elevator, sorting and chute. Documentation available. On-site inspection is possible. Bjdot Eu Azepfx Aa Eold

Condition: good (used), Mouth width: 150x80mm 2 rotor blades (95mm) Blsdofhnv Ispfx Aa Eed

Condition: used, Year of construction: 2002, turning diameter 630 mm turning length 3000 mm swing diameter over bed slide 480 mm turning speeds 9 - 1800 U/min spindle bore 83 mm tailstock quill taper MT 6 total power requirement 22 kW weight of the machine ca. 5400 kg dimensions of the machine ca. 5250 x 1900 x 1750 mm Features: - Digital display - 3-jaw chuck Ø315 mm ROTA-S PLUS - MULTI-FIX quick-change holder - Digital speed display - Coolant device - Rapid traverse longitudinal and horizontal - Steady rest - Live center - Lathe chuck guard - Chip guard - Machine light - Machine feet Bledjwz Rvlopfx Aa Ejd - Operating instructions

Condition: like new (used), Year of construction: 2019, Arburg 1200 T 2000-800 (vertical machine with rotary table 1200mm) Clamping unit 2000T Table diameter: 1200mm Angle rotation: 180 degrees Clamping force: 200 tons Opening force max. kN/mm: 115/500 Platen daylight max. : 600 mm Injection unit Screw diameter: 45 mm Shot volume: 318 cm3 Shot weight: 291 g Injection pressure: 2470 bar 1. Model: T model 2. Machine type: 1200 T 2000 - 800 3. Plasticizing unit: Thermoplastics cylinder 45 mm, highly wear-resistant 4. Screw: Reinforced screw coupling for splined coupling geometry Bjdowugczopfx Aa Esld 5. Control system: SELOGICA ‘direct’ controller 6. Technology stage: Stage 2 servo-regulated with 2 control pumps 7. Rotary table: Advanced ergonomics special model, 2-station 180° forward/backward alternating 8. Nozzle: Open nozzle 45 mm with nozzle tip 9. In-mould needle nozzles: Electric & hydraulic control for needle nozzle 1, electric & pneumatic control for needle nozzle 2 10. Heating: Heater band for open nozzle, 9 electric heating control circuits for mould heating 11. Clamping platen: Mould mounting platen set, central diameter 125 mm 12. Blow unit: Mould blow unit with pressure reducer at station 1 13. Safety: Optical barrier at loading station, continuous oil cooling and filtration 14. Hopper: Adapter (extension) for feed hopper, machine delivered without 50 L hopper 15. Robot interface: Interface for robot system for station 2 & 3 (based on EM67/1) 16. Electric axes: Basic equipment for electric axes control 17. I/O: 4 programmable inputs/outputs on terminal rail 18. Sockets: Additional socket combination (1 CEE, 1 Schuko) 19. Interfaces: Temperature control device interface (REGLOPLAS), printer USB interface, Compact Flash, EUROMAP 65 chip card user authorisation 20. Acoustic alarm: Error alarm acoustic signal 21. Safety interlock: Interface for safety interlock of door (EUROMAP 73) 22. Cooling circuits: 3 regulated machine-related cooling circuits with flow indicator, 3 manually adjustable cooling circuits for second water manifold 23. Anti-corrosion: Anti-corrosion treatment for rotary table, sealing lip on outer diameter 24. Manual & labels: CD operating manual & spare parts list, Slovak language labels 25. Machine feet: Anti-vibration footplates 26. Other: Hydraulic ejector, external cycle start key, standard equipment packages, new ARBURG colour scheme 27. Display languages: IT/EN/SK

Condition: new, table diameter 900 mm table load 1,0 t swivelling range 135 Grad turning speeds 0,12 - 1,2 U/min 820 mm welding current 500 Ampere total power requirement 0,75 + 0,55 kW weight of the machine ca. 1,1 t dimensions of the machine ca. 1,5 x 1,0 x 0,9 m • Self-locking gear, therefore no forward and backward at eccentric Bljdpfxsfv Axxj Aa Eod Load. • Electronic components from Schneider, Siemens and Delta. • Frequency-controlled stepless speed of the turntable. • High stability due to the robust construction. • welding power transmission • CE certificate. • Very good price / quality ratio. • The D-HBE series comes as a standard version with a cable remote control and delivered with a footswitch.

Condition: new, table diameter 2500 mm table load 20,0 t swivelling range 0 - 135 Grad turning speeds 0,04 - 0,4 U/min max. torque on the faceplate 40000 Nm table pass 200 mm welding current 1000 Ampere total power requirement 5,5 + 11,0 kW weight of the machine ca. t ELDING TABLE WITH LARGE THROUGH BORE Blodpfx Aajfv Axms Ejd • Self-locking gearbox, no pre- or after-run with eccentric load. • Electronic components from Siemens and Schneider. • Frequency-controlled, very accurate speed control. • Turntable with large through hole and T-slots. • High stability through a clever construction. • CE certificate. • Very good price / quality ratio. • The D-TLP series comes with remote control and foot pedal (left / right). No original pictures. Design but identical.