Manitou Winch 7.2T Vario (Demo)

Manitou Winch 7.2T Vario (Demo)

Condition: used, Year of construction: 2009, operating hours: 6,164 h, Doppstadt IDC000123 - manufacturer: Doppsttadt - model: DZ 750 Kombi - year of production: 2009 - gross vehicle weight: 46 000 kg - working hours: 6145 Codpfx Asvy S Dpob Tsaa

Condition: used, Year of construction: 2024, operating hours: 95 h, maximum speed: 40 km/h, Operating hours: 95, First registration: 15.01.2025 Basic Equipment / Technical Data Codpfx Aeuycgfob Teaa - Max. lifting capacity: 4,200 kg - Max. lifting height: 7,000 mm - Max. outreach: 3,800 mm - Length to tool carrier: 4,730 mm - Width: 2,310 mm - Height: 2,530 mm / 2,590 mm (CS activated) - Total weight with forks: 8,170 kg - Total weight without forks: 8,000 kg - Engine: 4-cylinder Deutz TCD 3.6, 3.6 l displacement, water-cooled - Power: 105 kW (143 HP) - 2,300 rpm - Hydraulic reversible fan - Stage V - Diesel particulate filter, oxidation catalyst and SCR catalyst with AdBlue injection (DPF + DOC + SCR) - Hydrostatic drive - Pump: electronically controlled with variable displacement - Motor: variable displacement motor - EPD TOP incl. optional automatic rpm increase - Mineral hydraulic oil HVI 46 - Transmission: 2 gears, electrohydraulically controlled - Vmax = 1st gear / 2nd gear = 16 / 20 km/h, optional 40 km/h Cabin - Enclosed cab - Split door - 360° all-round visibility - V3611 GRAMMER air-suspended seat with lap belt - ROPS/FOPS-certified - Heating - Front, roof and rear windshield wipers - Sunblind - 4x1 joystick electronic with capacitive release incl. direction selector switch - CS = hydropneumatic cab suspension Telescopic Boom - 2-part telescopic boom with electronic end position damping (Soft Stop) Attachment - Quick coupling system type "ZM2", hydraulically controlled from the cab Steering - Hydraulic steering - 3 steering modes: all-wheel, front-wheel, crab steering Drive - Permanent all-wheel drive Axles - Front axle fixed - Rear axle oscillating Braking System - Power-assisted disc brakes on all four drive wheels, automatically acting parking brake when the engine is off Chassis - High-strength steel frame design Hydraulic System - Load Sensing pump with variable displacement - Work hydraulics flow rate: 150 l/min - Hydraulic fan flow rate: 46 l/min - Total flow rate: 196 l/min - Working pressure: 250 bar - Flow-sharing control block Electrics - 12 V - 100 Ah battery - 120 A alternator Stabilisation Control - Simplified Merlo ASCS system (ASCS-light) with fully electronic stability control, audio-visual signal, attachment recognition, and overload shutoff Tyres - 460/70 R 24 Michelin XMCL Standard Equipment - Servo-assisted brake - Hydraulic oil cooler - Rear mounting plate for trailer hitch (AHK) - Hydraulic reversible fan - Radio pre-installation - Work lights on cab (2 front, 2 rear) - Preparation for additional function at boom head - 2 hydraulic connections at boom head - Load protection grate on tool carrier - Lighting for road use - Automatic battery main switch - Electric connection cable in boom - Acoustic warning signal when reversing - Boom support cylinder for securing Optional Equipment - EU approval as tractor 40 km/h incl. self-locking trailer coupling, 30/32 mm pin, incl. trailer lighting connection - Air conditioning - Boom suspension (B.S.S.) - LED work lights on cab (2 front, 2 rear) - 2 work lights at base of first boom section - ASC

Condition: new, Straightening press 150 tons with electric motor and additional manual operation by a hand lever pump, especially for fine work. Versions: 30t 60t 100t Casdpfx Abef Sqckj Tea 150t 200t ᐳ 200 t: on request Special machines: on request New machine! We are also happy to build a customer-specific press for you. High quality hydraulic workshop press with 150 tons maximum pressing force. The press can also be opened and closed in the classic electric mode using a lever. For fine work (e.g. pressing in bearings, straightening, ...) the press also has a hand pump. This allows you to fine-tune the force manually. The printing cylinder is attached to a sliding carriage so that the cylinder can be moved sideways. In this way, you can make optimal use of the maximum stand passage width. Particularities: - 150 tons maximum pressing force - Pressure display with manometer - 2 operating modes: electrical operation or or manual operation - 2 independent hydraulic pumps - Control cabinet with motor protection monitoring and safety devices - adjustable passage height - Pull chains for easy adjustment of the passage height - massive machine frame - cylinder laterally adjustable (mounted on sliding carriage) The press can be tested under power on site. ----- Numerous other workshop presses in different designs, sizes and with optional additional equipment available! 30, 60, 100, 150, 180, 200 tons. ----- Please just contact us, we will be happy to advise you without obligation. The stated price is net plus 19% VAT. All statements without guarantee! Europe-wide delivery possible! ----- The European Commission provides a platform for out-of-court online dispute resolution (OS platform). The offer serves exclusively as an internet presentation of our goods. The contract negotiation comes about by means of telecommunication (email, fax, telephone, news portal), where we first make you a non-binding offer, in which we inform you about our general terms and conditions and the right of withdrawal with imprint before the purchase / contract is concluded. Please just contact us, we will be happy to advise you without obligation.

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm Cjdehzbipspfx Ab Toaa - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: like new (used), Year of construction: 2008, functionality: fully functional, mobile shredding machine - used- rebuilt - Arjes 760 D with magnet on wheelaxle Complete conversion to hydraulic drive -- High Performance Shredder -- the most powerful shredder in this size Caodpfsv Dtfvex Ab Tja for heavy applications RECONSTRUCTION Machine was completely dismantled and rebuilt by steel construction. Conversion to hydraulic drive system Engine: Mercedes Benz OM 471 Stage 3 350 KW / 477 HP!!! (without AdBlue) - Gearbox: SYNCHRONOUS: 2x125,000NM - Hydraulics: Bosch Rexroth -- 285cbcm pump + 2x 215cbcm hydraulic motors - Control: NEW - Hydraulic lines: NEW - Radio: NEW - Shafts / tools: NEW (Combined tool for wood, garbage, light scrap) Machine is equipped with secondary crusher bars WERT GmbH is a metalworking company specializing in the development and production of twin-shaft shredding tools for renowned brands such as Hammel, Arjes, Linder, Eggersmann, Terex, and Keestrac. With an in-house design department and a highly skilled team, we provide customized, innovative solutions that meet the highest quality standards. Our goal is to continuously meet the individual needs of our clients through technological excellence and improvement. We serve companies across various sectors, including waste management, recycling, and mechanical engineering, and place great importance on long-term partnerships. With our reliable and high-performance shredding solutions, we help our clients increase their efficiency and competitiveness.

Condition: good (used), Year of construction: 1992, Automatic band saw JAESPA Type:W400 AZ Control Minipos 807 year 1992 Cutting diameter round material max. 400mm Sägebandlänge:5500X32X1,1mm Feed automatic cut length min.20mm Chip conveyor Caodpfx Absgf H Sas Tja Total power requirement 4 Kw Weight approx.2500kg Accessories 2X saw blades, roller table 6m motor drive, machine documentation available. Footprint : 2,8X2,8X2m

Condition: good (used), Year of construction: 2011, machine/vehicle number: MS 1153, Offer 23158 Technical data ca : - passage to blasting chamber B 370 x 170 mm - blasting nozzle - Door opening to blasting chamber - Blasting material pressure vessel - blasting material recovery - separate control panel - space requirement blast machine 1600 x 2000 x H 1750 mm - space requirement blasting material container 1200 x 1200 x H 2250 mm - Cartridge filter with suction fan MUNK - SCHMITZ Caodpjllvr Defx Ab Toa - Air volume 700 - 1500 m³/h - Suction fan 3 kW - space requirement filter unit 1600 x 1600 x H 3250 mm - mot. driven inlet roller table 4 m - roller table without drive 3 m - roller width approx. 800 mm - roller table height approx. 700 mm

Condition: new, machine/vehicle number: wtcs750s, Westtech Woodcracker CS750 Smart - available immediately Equipment: - Tiltator can be rotated continuously - Cutting diameter: 750 mm - Grab opening width: 1,280 mm - Own weight (basic - fully equipped): 820 - 980 kg - Recommended liter output: 65 - 110 l/min - Recommended operating pressure: 230 -280 bar - Service weight of carrier vehicle: 15 - 30 t - Saw box: actively suspended - Chain lubrication of saw: grease - Optional: Power tiltator can be rotated continuously Codpfx Aboiady Ej Toaa Available in multiples / fits perfectly with Magni RTH 6.30 SH & Magni RTH 6.35 SH. Can also be offered in conjunction with a Magni. Also fits Merlo. We are an official Westtech Woodcracker sales and service partner, Magni telehandler sales and service partner, JCB construction machinery sales and service partner, Mercedes-Benz service partner, Iveco service partner and, with 800 used vehicles, one of the largest commercial vehicle dealers in Germany. We supply the complete Westtech Woodcracker range for you!

Year of construction: 2025, condition: new, Maintenance-friendly dedusting system specially developed for aggressive sandblasting dusts with pre-chamber impact separator, complete essentially consisting of: a) 1 cartridge dry filter, type PF 1.4.B62.00 5000m³/h (other sizes available) Codpfjlxyhfex Ab Toaa each consisting of a stable, vacuum-tight 3 mm sheet steel housing, divided into the raw gas chamber with filter cartridges, filter pre-chamber impact separator and clean gas chamber with filter cleaning by means of compressed air, each with separate Easy Open maintenance door. Dust collection hopper with slotted valve for dust disposal using big bags. Solenoid valve control with differential pressure display for optimum adjustment of the filter cartridges - cleaning. Maintenance doors as swing doors Maintenance easy.

Condition: ready for operation (used), functionality: fully functional, fuel type: diesel, color: green, overall weight: 12,900 kg, maximum load weight: 3,800 kg, lifting height: 15,740 mm, Year of construction: 2007, operating hours: 6,100 h, machine/vehicle number: Roto 38.16, Equipment: UVV, all wheel drive, hydraulics, pallet forks, Rotating Telehandler Technical Specifications Working Height: 15.74 m Lateral Reach: 12.98 m Swivel Range: 415° Length: 6.24 m Width: 2.24 m Clearance Height: 2.85 m Load Capacity: 3,800 kg Work Platform Capacity: 300 kg Total Weight: 12,900 kg Support: Outriggers Power: Diesel Attachment: Forks Driver's License Class: 3/B Dates/Stands UVV (German Accident Prevention Regulations) until 11/2025 Operating Hours: 6,100 hours as of February 2024 Casdpfx Aetucp Teb Tea Interested? Then we're happy to help you at any time. You can reach us Monday to Friday from 7:00 a.m. to 4:00 p.m.! The stated price excludes VAT. Subject to change and errors!