Pallet fork

S60

Condition: used, functionality: fully functional, Year of construction: 2021, operating hours: 14,100 h, load capacity: 45,000 kg, lifting height: 15,100 mm, fuel type: diesel, mast type: duplex, power: 196 kW (266.49 HP), drive type: Diesel, construction width: 4,150 mm, Full-container reach stacker Mast type: Duplex Condition: Ready for operation and fully functional Technical condition: very good Front tire type: Pneumatic Front tire size: 18.00-25 Front tire condition: 60 - 80% Rear tire type: Pneumatic Gusdpfx Aezllhuoa Eod Rear tire size: 18.00-25 Rear tire condition: 60 - 80% Central lubrication system

Condition: excellent (used), Year of construction: 2003, Arburg 320S 500-60 Year of manufacture: 2003 Injection Unit: Screw diameter: 18 mm Gsdszc Nkcspfx Aa Eoud Shot weight: 18 g Injection pressure: 2500 bar Dosage volume: 20 ccm Clamping Unit: Clamping force: 50 t Tie bar spacing: 320x320 mm Platen size: 446x446 mm Ejector: hydraulic Clamping system: hydraulic Control: SELOGICA Additional Equipment: Euromap 12 Robot interface Air valve x 1 Controller with 6 hot runner zones Hardened injection unit - bimetallic Dimensions: Weight: 2,350 kg Length/Width/Height: 3.32x1.24x1.81 m Drive: Pump/Motor: 11 kW Heating capacity: 4 kW Total power: 15 kW All machines offered are started and tested by our service technicians before sale. It is possible to receive a video of the technical tests of the selected machine or to participate in live technical tests at our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2008, Arburg OK-C S350-60 / Vertical injection molding machine with sliding table / Very good technical condition Year of manufacture: 2008 injection unit: screw diameter: 18 mm injection weight: 18 g injection pressure: 2500 bar Dosing volume: 20 ccm Clamping unit: Clamping force: 35 t tie bar distance: 0x0 mm size of clamping platens: 295x395 mm ejector: hydraulic clamping unit: hydraulic Control system: SELOGICA - touch screen Additional equipment: Vertical injection molding machine with sliding table 3 stations on the sliding table Gedpfezc Ngwox Aa Eeud Air valve x 4 Hydraulic core pull x 1 Control system with hot runners Injection unit hardened - bimetal Parallel movements Infrared protection curtains It is possible to change the screw diameter Dimensions: Weight: 2500 kg Length/width/height: 2.55x1.85x3.52 m All offered machines are started by our service technicians before sale. It is possible to get a video of technical tests of the selected machine or participate in live technical tests in our company in Łódź. Price: Upon request

Condition: new, Sick DFS60B-S1AA01024 incremental encoder, serial number as shown in the photo, unused in opened original packaging, 100% functional, scope of delivery as shown in the photos. Gusdpfx Aei Ec Upja Esd

Condition: ready for operation (used), Year of construction: 2001, operating hours: 91,550 h, clamping force: 400 kN, screw diameter: 25 mm, Hydraulic injection moulding machine manufactured in 2001. This Arburg 270 S 400-60 features a screw diameter of 25 mm and an additional cylinder suitable for Teflon processing. The machine is in working condition, with 98,077 pump hours and 91,550 automatic hours. If you are looking to get high-quality moulding capabilities, consider the Arburg 270 S 400-60 machine we have for sale. Contact us for further details. • Machine Pump Hours: 98,077 h • Automatic Hours: 91,550 h • Screw Diameter: 25 mm Gjdpfx Aezkh Rvja Eeud • Additional Cylinder: 25 mm (suitable for Teflon processing) • Clamping Unit: Closes without damping • Condition: Machine in working condition

Condition: used, Year of construction: 2015, mast type: telescopic, fuel type: diesel, Lifting capacity: 227 kg Guodpfezlm Ngex Aa Ejd Please contact Gebrauchtgeräte Center for more information

Condition: used, mileage: 467,100 km, power: 260 kW (353.50 HP), first registration: 01/2016, fuel type: diesel, number of seats: 60, gearing type: automatic, emission class: euro6, color: white, brakes: retarder, Equipment: ABS, air conditioning, parking heater, * Our internal number: 1168 * S 516 MD * Retarder Gjdpexwr Apefx Aa Eeud * French inspection certificate is available. * Currently fitted with 58 seats (no reclining seats) --> therefore, the number of seats can be increased. * An additional row of seats is included separately, allowing for 60 seats. * The following repairs were carried out at EVOBUS in June 2026: * Retarder replaced * Retarder control unit replaced * Exhaust gas recirculation valve replaced * Haldex separator replaced * 2 x V-belts replaced * Air reservoir with drain replaced * Oil separator replaced * Cost: 8,500 EUR / net * In July 2026: Air conditioning service performed * Side matrix (without control unit) * Interior route display * Seats can be adjusted to face backwards * LIFT * Lifting mechanism - trunk lid on the right side * Storage compartments * Convector heater * Auxiliary heater * Air conditioning * Rear entrance * No toilet, no refrigerator. * Wheelchair-accessible bus * The customer is obliged to independently verify the condition and equipment of the goods/vehicle! * etc. * Vehicle may be in operation / mileage and condition may vary. * All information is subject to change without notice. * We reserve the right to sell the vehicle in the meantime. * We refer to our general terms and conditions.

Condition: used, Feed opening: approx. 600 x 580 mm Rotor width: approx. 600 mm Rotor diameter: approx. 450 mm Guedpfezixtfsx Aa Eed Stator knives: 2 Rotor knives: 4

Condition: used, empty load weight: 8,446 kg, axle configuration: 3 axles, first registration: 02/2018, tire size: 385/65 R22.5-385/65 R22.5, Year of construction: 2018, mileage: 556,803 km, Ref: 50961 Gsdpfjzk Rl Aex Aa Ejud Equipment: * Air connection: Red/Yellow connector, * Electrical connection: 1 x 15-pin + 2 x 7-pin, * ABS, * EBS, * Electrical cable for refrigeration unit, * Fire extinguisher: 1, * Document box, * Side impact protection, * Lifting odometer, * Wheel chocks: 1, * Toolbox: 1, * Access ladder, * Rear door design: Rear portal doors, * Locking bars on rear doors: 2, * Floor: Aluminum floor, * Double-deck system, * Double-deck beams: 22, * Spare wheel holder: 2 VIN: WSM000005200425 Tire size: 385/65 R22.5 Width: 2.6m Height: 4m

Condition: excellent (used), CTS Type: CSR-60/810/S Temperature & Climate Air Conditioning Unit, Air-Cooled CTS Climate Test System CSR-60/810/S | –60°C to +170°C 39.6 kW | Test Chamber 1200 L Description: For sale is a professional climate and temperature testing system manufactured by CTS GmbH, comprising a conditioning unit type CSR-60/810/S and an external test chamber (1200 liters). Gjdpozimgajfx Aa Eoud The system is ideally suited for industrial, R&D, and laboratory applications, e.g., for automotive, electronics, component, and material testing. It enables precise temperature and climate simulations across an extremely wide operating range. This is a professional climate and temperature conditioning system from CTS GmbH, including: • Conditioning unit (CSR-60/810/S) • External test chamber (1200 L chamber) The system is designed to supply external test rooms or chambers with precisely controlled temperature and humidity. Typical applications include industrial, automotive, electronics, material, and component testing (environmental simulation, stress screening, endurance testing). Technical Data (from nameplate & manual) General: Manufacturer: CTS GmbH, Hechingen Type: CSR-60/810/S Year of manufacture: 07/2019 Temperature & Climate Temperature range: –60°C to +170°C Humidity range: 10% to 80% RH Dew point range: +5°C to +74°C Electrical Data: Rated voltage: 400 V / 3-phase / N / PE / 50 Hz Rated power: 39.6 kW Rated current: 64.9 A Recommended fuse protection: 80 A slow-blow Connection type: Hardwired Refrigeration System Refrigerants: Pre-cooling stage: R452A (17.0 kg) Cooling stage: R23 (5.3 kg) Compressor: Bitzer (cascade system) Protection class: Conditioning unit: IP54 Test chamber: IP22 Dimensions & Weight: Conditioning unit: Dimensions (W x D x H): approx. 1,200 × 1,100 × 2,200 mm Weight: approx. 1,200–1,500 kg 1200 L Test Chamber: Dimensions (W x D x H): approx. 1,600 × 1,400 × 1,600 mm Weight: approx. 600–800 kg Total system weight: approx. 1.8–2.3 t Buyer Safety Information! The following steps are always carried out on our offered chambers before sale: 1. Functional check and replacement of necessary components 2. If necessary, refilling with legally compliant refrigerant 3. Leak test with certificate 4. After successful check, the chambers undergo a documented test run. Condition: used Scope of delivery: (see pictures) (subject to change and errors in technical data and specifications!) Additional questions can gladly be answered over the phone.