Second-hand machinery for sale (200,000)

Year of construction: 2025, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 54942, No minimum price – guaranteed sale to the highest bidder! EXW – Dismantling and loading must be organized by the buyer! TECHNICAL DETAILS Nominal test force: 50 kN Test stroke: < 1,400 mm Usable distance between pressure plates: approx. 800 mm Test area width: 500 mm Test speed: continuously variable 0.001–1,200 mm/min Resolution of displacement measurement: ≤ 0.001 mm Lsdpfx Absz Tf D Ro Ashn Diameter of pressure plates: 246 mm Centering bore: 40 mm Thread: M12 Hardness: ≥ 56 HRC Design: Steel, hardened, rotatable at the top and bottom, lockable at 0° Measuring range of the enveloping circle: 30–250 mm Design: Probe with bearing rollers Measurement: Recording under load MACHINE DETAILS Control system: Control system with control computer Test program: Enveloping circle measurement Network: Fast Ethernet, 100 Mbit/s between the control computer and the separately required operating PC Software delivery: USB stick with installation software Documentation: Version and license status not documented separately Last calibration: 08/04/2025 Dimensions & Weight Machine dimensions: approx. 750 × 900 × 1,950 mm Base frame dimensions: approx. 730 × 900 × 700 mm Control cabinet with control computer dimensions: approx. 600 × 600 × 1,900 mm Machine weight: approx. 490 kg Base frame weight: approx. 50 kg Voltage supply: 3 × 400 V AC, 50 Hz, N + PE Type plate power: 3,000 W Connected power: approx. 3 kVA EQUIPMENT Base frame Control cabinet with control computer Rotatable pressure plates Enveloping circle measuring device with probes and bearing rollers USB stick with installation software Compressed air connection: Pneumatic connection with shut-off valve Note: The functionality has been tested and confirmed. However, an unresolved error message on the drive prevents further use. The machine is in like-new condition visually. The operating PC is not included in the offer.

Condition: used, Year of construction: 2010, machine/vehicle number: 1000017741, inner dimension length: 1,000 mm, inner dimension width: 840 mm, inner dimension height: 815 mm, operating temperature: 1,700 °C, usable tank capacity: 685 l, No minimum price – guaranteed sale to the highest bidder! The machine was professionally dismantled and stored. All parts and connections are labeled for reassembly. An on-site inspection is possible at any time. Lhsdez I Tt Iopfx Ab Aon TECHNICAL DETAILS Furnace chamber and usable space Usable batch space (W × H × L): 840 × 815 × 1,000 mm Total length of the graphite box: approx. 1,100 mm Usable volume: approx. 685 l Operating temperature: max. 1,700 °C Operating temperature under partial pressure: max. 1,500 °C Operating temperature under vacuum: max. 1,700 °C Temperature uniformity: ± 10 K Temperature fluctuation in the steady state: ± 5 K MACHINE DETAILS Process pressure range: 1 × 10⁻² < p < 1,040 mbar Final pressure in the empty, clean, and cold furnace: < 1 × 10⁻² mbar Leak rate: < 5 × 10⁻³ mbar·l/s Power supply: 3 × 400 V, 50 Hz Permissible voltage fluctuation: max. ± 5 % Installed heating power: max. approx. 190 kW Electrical power of the pump station: approx. 14 kW Cooling water flow rate: approx. 150 l/min Cooling water temperature: 20–30 °C Cooling water pressure: 2–4 bar Cooling water quality requirements: according to specification PW 800 943 ND Compressed air for valve operation: 4–5 bar Nitrogen inlet pressure: 5–7 bar Hydrogen inlet pressure: 5–7 bar EQUIPMENT Double-walled furnace chamber made of stainless steel with water cooling Internal graphite box for precise guidance of the process gases Post-cleaned graphite components Automatic control of the entire process Pump station Labeled lines and connections for easier recommissioning Note: Two internal graphite heating elements were damaged during dismantling and must be replaced.

Condition: excellent (used), Year of construction: 2016, TECHNICAL DETAILS Control System CNC control: FANUC Professional 5 Axes and Travel Ranges X-axis: 550 mm Y-axis: 1,000 mm Z-axis: 500 mm C-axis: 360°, continuous rotation A-axis: 150° (+30° / 120°) C-axis measuring system: Rotary encoder A-axis measuring system: Rotary encoder Feed Rate and Rapid Traverse Feed rate X-axis: 32 m/min Feed rate Y-axis: 40 m/min Feed rate Z-axis: 40 m/min Rapid traverse X-axis: 48 m/min Rapid traverse Y-axis: 50 m/min Rapid traverse Z-axis: 50 m/min Rapid traverse A-axis: 18 m/min Rapid traverse C-axis: 18 m/min Work Table and Workpiece Table dimensions: 500 mm Maximum workpiece size: 650 × 500 mm Workpiece weight: max. 350 kg Spindle Spindle speed: max. 14,000 rpm Tool System Tool holder: HSK-A63 Tool magazine: 323 positions Tool changer: Double gripper Tool diameter: max. 70 mm Tool diameter with adjacent occupied positions: max. 140 mm Tool length: max. 300 mm Tool weight: max. 8 kg Operating Hours Lhedpfx Ae Aayfhsb Asn Total operating time: 63,813 h Spindle running time: 30,592 h Machine Dimensions and Weight Length: 3,550 mm Width: 2,900 mm Height: 3,200 mm Machine weight: 15,700 kg EQUIPMENT Electronic handwheel Chip conveyor Measuring probe

Year of construction: 2021, operating hours: 17,634 h, condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Lift Mast Mast type: Duplex mast Lift height: 5,495 mm Free-lift mast: Without center hydraulic cylinder Free lift: No Load Capacity and Forks Load capacity: 3,500 kg Fork length: 1,200 mm Hydraulically adjustable forks: Yes Side shifter: Yes Drive Drive type: LPG (liquefied petroleum gas) Diesel drive: No MACHINE DETAILS Machine data Manufacturer: Linde Type: H35T Year of manufacture: 2021 Operating hours: 17,634 h Self-weight: 5,516 kg UVV certificate valid until: Formerly a Linde full-service unit Facelift model Dimensions Overall length: 5,200 mm Overall width: 1,450 mm Overall height: 3,424 mm EQUIPMENT 3rd and 4th hydraulic valve Fork positioner with side shifter Full cabin Air conditioning Heater Windshield wiper Comfort seat with lumbar support Seat heating LED work light, front LED work light, rear Road traffic lighting with turn signals Orange warning light Safety light, front Safety light, rear All dimensions are rounded values. No guarantee is given for typing or measurement errors. Collection conditions: Lateral loading up to 6 tons is possible with a large forklift on site. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receipt of payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. Ljdpfez R Dqwox Ab Ajhn In the event of delayed collection, a storage fee of €20 per machine per day will be charged. Outstanding storage fees must be paid in full before collection. Lot number: 45

Condition: used, machine/vehicle number: CT1133L70678, Year of construction: 2021, operating hours: 6,200 h, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Load capacity: 1,200 kg Lifting height: 1,924 mm Fork length: 1,150 mm MACHINE DETAILS Battery year of manufacture: 08/2021 Battery voltage: 24 V Battery capacity: 375 Ah Battery voltage at rest: 25.3 V Dimensions & Weight Dimensions (L x W x H): 2,500 x 800 x 2,200 mm Weight: 1,500 kg Service valid until: 03/2027 UVV (occupational safety) valid until: 03/2027 Lhsds Ad Rdiepfx Ab Aon Operating hours: 6,200 h EQUIPMENT Initial lift Formerly a Linde full-service unit All dimensions are approximate. No guarantee is given for typographical or measurement errors. Collection conditions: Lateral loading up to 6 tons is possible using a large forklift on site. Loading is done at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons and up to a width of 230 cm. Collection is only possible after receiving payment confirmation by email. Collection without prior registration is possible from Monday to Friday between 07:00 and 16:00. If collection is not carried out on time, a storage fee of €20 per machine and day will be charged. Any outstanding storage fees must be paid in full before collection. Lot number: 337

Condition: ready for operation (used), Year of construction: 2018, operating hours: 13,270 h, laser type: fiber laser, laser power: 4,000 W, sheet thickness (max.): 20 mm, overall weight: 9,700 kg, year of last overhaul: 2025, The system must be dismantled between November 20, 2026, and November 22, 2026! TECHNICAL DETAILS Laser type: Fiber laser Laser power: 4,000 W Sheet metal thickness (max.): 20 mm Sheet metal thickness steel (max.): 20 mm Sheet metal thickness stainless steel (max.): 20 mm Sheet metal thickness aluminum (max.): 20 mm MACHINE DETAILS Control type: CNC control Automation level: Automatic Actuation type: Electric Power: 4 kW (5.44 hp) Input voltage: 400 V Input frequency: 50 Hz Type of cooling: Water Compressed air connection: 7 bar Laser operating hours: 13,270 h Year of last overhaul: 2025 Dimensions & Weight Dimensions (L x W x H): 9,310 x 7,813 x 2,300 mm Total weight: 9,700 kg EQUIPMENT CE marking Central lubrication system Cooling unit Lodjz I S Uwopfx Ab Aehn Documentation/Manual Dust extraction Emergency stop switch Fume extraction Safety light curtain

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, Weinig Dimter Profipress C 2800 P - 6 m gluing press Manufacturer: Weinig Dimter Model: Profipress C 2800 P - 6 m Year of manufacture: 2009 Condition: Very good Machine description: For sale: Weinig Dimter Profipress C 2800 P - 6 m wood gluing press, year 2009, designed for the production of glued wooden panels and elements made of soft timber. The machine was developed for efficient production using PVAC glue in D2 / D3 class and allows processing of material within specified width, thickness and input length ranges. According to the documentation, this model can process timber with widths from 30 to 80 mm, thicknesses from 15 to 40 mm and input lengths from 2100 to 2800 mm. The machine allows the production of panels with variable widths from 600 to 1200 mm. For short lengths, the collecting distance range is 700 to 1400 mm. The output is up to 10 to 15 infeeds per minute, depending on the entrance width. The Profipress C 2800 P - 6 m is intended for processing soft timber. The permitted bending tolerance is maximum 5 mm per meter. The documentation also specifies recommended operating conditions, including room temperature from 15 to 30 degrees Celsius and air humidity in the range of 40 to 65 percent. Technical data: - Model: Profipress C 2800 P - 6 m - Year of manufacture: 2009 - Performance: max. 10–15 infeeds/min, depending on entrance width - Timber width: 30–80 mm - Timber thickness: 15–40 mm - Timber entrance length: 2100–2800 mm - Collecting distance for short lengths: 700–1400 mm - Panel width: 600–1200 mm - Timber type: soft timber - Permitted bending: max. 5 mm/m - Glue type: PVAC D2 / D3 - Recommended room temperature: 15–30°C Lhjdpsyvgiasfx Ab Ajn - Recommended air humidity: 40–65% Features and advantages: - Press designed for glued panel production - Machine from the renowned Weinig Dimter brand - Output up to 10–15 infeeds per minute - Possibility to produce panels with variable width - Suitable for processing soft timber - Works with common PVAC D2 / D3 glue - Industrial application for woodworking and production plants

Condition: ready for operation (used), Year of construction: 1985, machine/vehicle number: 1304, functionality: fully functional, pressing force: 367 t, stroke length: 100 mm, table width: 525 mm, table length: 430 mm, table height: 800 mm, No minimum price – guaranteed sale to the highest bidder! EXW – Buyer is responsible for dismantling and loading! The machine was rebuilt in 2018! TECHNICAL DETAILS Lsdpjz Tf Enjfx Ab Ashn Press force: max. 3,600 kN Ram stroke: max. 100 mm Ram adjustment: 40 mm Stroke rate: 40 strokes/min Table area: 430 × 525 mm Table height: 800 mm MACHINE DETAILS Connected power: 7.5 kW Mains connection: 3-phase, 380 V, 50 Hz Control voltage AC: 220 V Control voltage DC: 24 V Main motor power: 7.5 kW Oil capacity: 50 l Ambient temperature: +5 °C to +40 °C Average temperature over 24 h: max. +35 °C Humidity: 30–95 %, non-condensing Altitude: 1,000 m above sea level Noise level: ≤ 70 dB Dimensions & Weight Dimensions (W x D x H): 1,200 x 2,000 x 2,400 mm Space requirement: approx. 1,500 mm Machine weight: 8,000 kg Control cabinet dimensions: 800 × 1,200 × 300 mm Control cabinet weight: approx. 100 kg EQUIPMENT Operating manual Testing information Digital documentation Note: Induction unit is not included in the scope of supply.

Condition: ready for operation (used), functionality: fully functional, operating hours: 10,386 h, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS GENERAL Manufacturer: Still Type: RX20-18 Year of manufacture: 2019 Drive type: Electric Operating hours: 10,386 h Lhsdpfx Abj Ad N D Uj Ajn Load capacity: 1,800 kg LIFTING EQUIPMENT Mast type: Triplex mast Lifting height: 4,500 mm Full free lift: available FORKS AND HYDRAULICS Fork length: 1,000 mm Hydraulic valves: 3rd + 4th valve Fork positioner: hydraulic Side shifter: available BATTERY Battery year of manufacture: Battery voltage: 48 V Battery capacity: 898 Ah Battery idle voltage: 54.6 V MACHINE DETAILS DIMENSIONS AND WEIGHT Overall length: 3,000 mm Overall width: 1,150 mm Overall height: 2,060 mm Dead weight: 3,400 kg EQUIPMENT Battery charger Semi-cabin Lateral fall protection LED work light (rear) Orange warning light Comfort seat with lumbar support Seat heating Lot number: 229 Collection conditions: Lateral loading up to 6 tons is possible with a large forklift on site. Loading is at your own risk. Loading from the rear via ramp is possible for truck heights of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receipt of the payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. If collection is not carried out within the specified time, a storage fee of €20 per machine per day will be charged. Outstanding storage fees must be paid in full before collection.

Condition: used, Year of construction: 1971, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Working area Sheet metal width: 2,000 mm Sheet metal thickness for St 42: 16 mm Passage width: 2,250 mm Overhang: 600 mm Knife and cutting Knife length: 2,005 mm Cutting gap adjustment: 0.05–0.95 mm Cutting angle: 1° 40′ Clamping beam: 10 pcs. Back gauge Gauge length: 1,000 mm Back gauge adjustment: 10–1,000 mm Work table Table size: 2,500 × 700 mm Table height above floor: 800 mm Hydraulics and Electrics Oil volume: 900 l Operating voltage: 380 V Ledpez S Ng Hofx Ab Ajhn Machine data Machine weight: approx. 10 t Space requirement: approx. 3 × 2.3 × 2.3 m EQUIPMENT Foot switch Supports Spare knife

Condition: ready for operation (used), functionality: fully functional, operating hours: 4,777 h, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS General Manufacturer: Still Type: RX20-18 Year of manufacture: 2019 Drive type: Electric Operating hours: 4,777 h Load capacity and mast Load capacity: 1,800 kg Lifting height: 4,500 mm Mast type: Triplex mast Full free lift: available Battery Battery year of manufacture: 2019 Battery voltage: 48 V Battery capacity: 625 Ah Measured idle voltage: 50.83 V Hydraulics Hydraulic valves: 3rd and 4th valve Side shifter: available Hydraulic fork positioner: available Inspections and maintenance Service valid until: 10/2027 UVV inspection valid until: 10/2027 MACHINE DETAILS Dimensions and weight Length: 3,000 mm Width: 1,150 mm Height: 2,060 mm Own weight: 3,400 kg EQUIPMENT Battery charger Fork positioner with side shifter Lateral fall-through guard LED work light at the rear Orange warning light Comfort seat with lumbar support Seat heating Lot number: 219 Collection conditions: Side loading up to 6 tons is possible with a large forklift on site. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receipt of the payment confirmation by email. Collection without prior registration is possible from Monday to Friday between 07:00 and 16:00. Lsdpfx Ae Ad N Dnob Aohn If collection is not carried out on time, a storage fee of €20 per machine per day will be charged. Any outstanding storage fees must be paid in full before collection.

Condition: ready for operation (used), functionality: fully functional, operating hours: 10,598 h, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS GENERAL Manufacturer: Still Type: RX60-30 Year of manufacture: 2020 Drive type: Electric Operating hours: 10,598 h LIFTING CAPACITY AND MAST Lifting capacity: 3,000 kg Lifting height: 4,150 mm Mast type: Duplex mast Fork length: 2,400 mm BATTERY Battery voltage: 80 V Battery capacity: 620 Ah Battery year of manufacture: 2020 Battery date: 18/2020 (?) Battery voltage in idle state: 84.9 V INSPECTIONS AND MAINTENANCE Service valid until: UVV inspection valid until: MACHINE DETAILS DIMENSIONS AND WEIGHT Length: 4,900 mm Width: 1,200 mm Height: 2,750 mm Weight: 5,100 kg EQUIPMENT Former Still full-service unit Clear-view mast without center hydraulic cylinder Lodpfx Ae Ad N Dhjb Aohn 3rd and 4th hydraulic valve Hydraulic fork positioner Side shifter Half-cab with windshield wiper White, non-marking tires LED work light, front LED work light, rear Orange warning light Safety light, rear Comfort seat with lumbar support Lot number: 155 Collection conditions: Side loading up to 6 tons is possible with a large forklift on site. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receipt of payment confirmation by email. Collection without prior registration is possible from Monday to Friday between 07:00 and 16:00. If collection is not carried out on time, a storage fee of €20 per machine per day will be charged. Outstanding storage fees must be paid in full before collection.

Year of construction: 2011, condition: ready for operation (used), functionality: fully functional, conveyor belt length: 4,000 mm, conveyor belt width: 600 mm, machine/vehicle number: 3002097/2, TECHNICAL DETAILS Temperature range: Ambient temperature to -110 °C Design: Stainless steel mesh belt Belt length: 4,000 mm Belt width: 600 mm Lhjdpfez I Ti Aox Ab Aon MACHINE DETAILS Power supply: 3-phase EQUIPMENT Stainless steel mesh belt Continuous conveyor belt system Suitable for integration into continuous hardening systems

Condition: ready for operation (used), Year of construction: 2010, functionality: fully functional, MORI SEIKI HORIZONTAL CNC LATHE Model : NL2500Y/700 Year 2006 Lsdpe Ad Ubxefx Ab Aehn Max Swing Over Bed 925 mm Max Turning Diameter 356 mm Max Turning Length 705 mm Distance Between Centers 700 mm Bar Working Capacity 80 mm Standard Chuck Size 10” • X-Axis Travel: 260 mm • Z-Axis Travel: 795 mm • Y-Axis Travel: 100 mm / ± 50 mm • C-Axis Minimum Indexing: 0.001° • Main Spindle Speed: Max 4,000 RPM • Turret Stations: 12-position bolt-on type BMT turret • Live Tooling Speed: Max 6,000 RPM • Live Tooling Motor: 7.5 hp (5.5 kW) • CNC Control Unit: MSX-850 / MSX-850III (MAPPS III) • Tailstock

Condition: used, Year of construction: 2019, TECHNICAL DETAILS General Information Manufacturer: XYZ Machine Tools Model: SL 1100 / 1500 mm Machine Type: Heavy-duty CNC turning machine Year of manufacture: 2019 Condition: well-maintained Control System Control system: Siemens ShopTurn / Siemens CNC 840D Working Area Distance between centers: 1,500 mm Swinging diameter over bed: 1,100 mm Spindle bore: 165 mm Spindle and Drive Main drive: 70 kW Speed range: max. 660 rpm Machine Construction Bed width: 558 mm Machine bed: heavy cast iron construction Tailstock: included, electric Operating Condition Inspection: possible by appointment Functional test: possible via video before shipping or collection EQUIPMENT Siemens ShopTurn Siemens CNC 840D Electric tailstock Lhsdj Aayk Ropfx Ab Ajn Automatic central lubrication Coolant system Full enclosure Large chuck Safety guard Work area lighting

Condition: reconditioned (used), Year of construction: 2012, functionality: fully functional, CNC Universal – Machining Center DECKEL MAHO DMU 40 eVo NEW DMG Design With Heidenhain iTNC 530 HSCI control system Year of manufacture: 2012 Travel distances: X 400 Y 400 Z 375 Speed range: 20 – 18,000 rpm, stepless With the following accessories: NC rotary table 450 mm x 400 mm incl. table cooling 30-position tool changer with dual gripper 3D measuring probe Renishaw PP 60 optical Electronic handwheel Operating mode 4 Heidenhain table probe TD 110 (length measurement) Lhedpfxo Ad Up Ne Ab Asn IKZ 40 bar with paper band filter Chip conveyor Machine bed flushing Active cooler for control cabinet Spindle cooling: water circulation cooling Direct path measuring system Flushing gun for chip removal Rotoclear Oil mist extraction 3-piece height-adjustable machine feet Operating manuals Signal light, 4 colors

Condition: ready for operation (used), Year of construction: 1991, functionality: fully functional, machine/vehicle number: CO1040, The following components have been replaced: Engines Gearboxes Chains Ljdpsz I Tkmjfx Ab Ajhn TECHNICAL DETAILS Design: Double-shaft paddle mixer Material: Stainless steel Batch capacity: 1,200 kg EQUIPMENT Stainless steel storage container at the bottom

Condition: used, Year of construction: 1974, bore capacity in steel (diameter) 32 (St 60) mm arm length 418 / 1018 mm workpiece height max. ca. 400 mm table surface area 1200 x 500 mm spindle taper MT 4 quill stroke 190 mm distance table - lower edge spindle 260 - 660 mm Ledpfxj Ad Rlte Ab Aehn table height over floor 800 mm spindle turning speed range 41 - 1800 U/min feeds 0,1 / 0,15 / 0,2 / 0,3 mm/U total power requirement 6 kW weight of the machine ca. 1,8 t

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS COMPATIBILITY FEM class: FEM 3 Suitable for forklift load capacity: 3,000–5,000 kg Suitable for: Linde H50D FEATURES Design: 360° rotating device with rotating clamp Internal opening: approx. 400–1,800 mm Fork positioner: present (?) MACHINE DETAILS MANUFACTURER AND MODEL Manufacturer: Linde Type: Rotating clamp Year of manufacture: 2020 Previous use: Linde H50D with 5,000 kg load capacity DIMENSIONS Width: approx. 1,700 mm Height: approx. 1,000 mm Length: approx. 1,250 mm EQUIPMENT 360° rotating device Rotating clamp Fork positioner Lot number: 1139 Collection conditions: Side loading up to 6 tons is possible with a large forklift on site. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons and up to a width of 230 cm. Collection is only possible after receipt of payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. Lhedpfj Ad N Igex Ab Ajn If collection is not carried out on time, a storage fee of €20 per machine per day will be charged. Outstanding storage fees must be paid in full before collection.

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS General Manufacturer: Linde Type: D12HPSP Year of manufacture: 2021 Operating hours: 6,655 h Lifting Capacity and Lift Lifting capacity: 1,200 kg Lifting height: 1,924 mm Fork length: 1,150 mm Initial lift: available Pallet capacity: 2 pallets simultaneously Battery Battery year of manufacture: Week 44/2023 Battery voltage: 24 V Battery capacity: 375 Ah Measured battery voltage: 25.5 V MACHINE DETAILS Dimensions and Weight Overall length: 2,500 mm Overall width: 800 mm Overall height: 2,200 mm Own weight: 1,500 kg EQUIPMENT Initial lift for increased ground clearance on uneven surfaces Previously a Linde full-service machine Lodpe Ad N Eljfx Ab Ashn Lot number: 390 Collection conditions: Lateral loading up to 6 tons is possible with a large forklift truck on site. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receipt of the payment confirmation by email. Collection without prior registration is possible from Monday to Friday between 07:00 and 16:00. If collection is not carried out within the specified time, a storage fee of €20 per machine and day will be charged. Any outstanding storage fees must be paid in full before collection.

Condition: used, Year of construction: 2022, operating hours: 1,100 h, functionality: fully functional, load capacity: 2,000 kg, arm reach: 2,400 mm, Equipment: documentation/manual, For sale is a like-new IGM RTE 478-S welding robot, manufactured in 2022! This is a 7-axis robot with a 9-meter travel range and two stations, each equipped with a 2-axis L-manipulator with a load capacity of up to 2000 kg. Robot type: RTE 478-S in a suspended position. Control system: Fully digital PC robot control system, type RCE. Lodpfx Abs Ad R Eaj Ajhn Welding process: Single-wire welding process. Welding equipment: Digital inverter welding power source TPS 500i. The system can be inspected and tested upon request. The robot was operated in a single-shift operation and has few operating hours!

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS GENERAL DATA Manufacturer: Linde Year of manufacture: 2022 Type: 48 V / 20 Ah ELECTRICAL DATA Battery voltage: 48 V Battery capacity: 20 Ah Ljdpe Ad N S Ejfx Ab Ajhn MACHINE DETAILS DIMENSIONS AND WEIGHT Length: 600 mm Width: 600 mm Height: 800 mm Weight: 50 kg EQUIPMENT 2 lithium-ion batteries Charger Battery connector Wall plug Lot number 3632 Collection conditions: Side loading up to 6 tons with a large forklift on site is possible. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receiving payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. If collection is not carried out within the specified timeframe, a storage fee of €20 per machine per day will be charged. Any outstanding storage fees must be paid in full before collection.

Condition: ready for operation (used), Year of construction: 2010, functionality: fully functional, Horizontal Machine Center DMG MORI NH 5000DCG/40 Year 2010 Tavel X 730 Y 730 Z850mm Fully C axis 0.001 degree MAPPS FAUNC Spindle 14,000rpm Lhsdo Ad Ucispfx Ab Aon 37/22KW 303Nm HSK-A63 Taper 60 ATC Pallet 500 x 500mm

Condition: ready for operation (used), Year of construction: 2003, operating hours: 11,600 h, functionality: fully functional, spindle bore: 107 mm, spindle speed (max.): 4,000 rpm, overall weight: 10,000 kg, controller model: Siemens 810D, Equipment: chip conveyor, TECHNICAL DETAILS Maximum swing diameter: 680 mm Swing diameter over X-guide: 565 mm Longitudinal travel: 1,300 mm Cross travel: 315 mm Spindle head: h5 Spindle diameter at front bearing: 150 mm Spindle bore: 107 mm Maximum torque: 600 Nm Spindle speed: 4,000 rpm Chuck diameter: 315 mm Rapid traverse X-axis: 60 m/min Rapid traverse Z-axis: 45 m/min Tool turret for: 12 tools Driven tools: 12 Tool holder: VDI 40 Quill stroke: 120 mm Quill taper: MK 5 MACHINE DETAILS Control system: Siemens 810D Dimensions & Weight Machine dimensions with chip conveyor (L x W x H): 5,700 x 2,600 x 2,210 mm Machine weight: approx. 10,000 kg Operating Hours Power-on hours: 47,781 h Spindle hours: 11,600 h EQUIPMENT Hydraulic steady rest, clamping range 30-245 mm Lhodpfx Aboz N Aaus Aen Chip conveyor KNCS-N 315-91 power chuck

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Mounting Ledpfjz R Rgtox Ab Ajhn FEM class: FEM 3 Load capacity Load capacity: 3,000 kg Suitable for forklifts with a load capacity of: 3,000–5,000 kg Forks Fork type: Hydraulic telescopic forks / push forks Fork length: 1,350–2,350 mm MACHINE DETAILS Origin Previously mounted on: Linde H30 Year of manufacture: 2021 Dimensions and weight Overall length: 1,350 mm Overall width: 800 mm Overall height: 1,000 mm Self-weight: 200 kg EQUIPMENT Hydraulic telescopic forks / push forks All dimensions are approximate. No guarantee is given for typographical or measurement errors. Collection conditions: Side loading up to 6 tons is possible using a large forklift on site. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receipt of payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. If collection is not carried out within the specified period, a storage fee of €20 per machine per day will be charged. Outstanding storage fees must be paid in full before collection. Lot number: 1169