Uab Baltic Filter

Condition: new, Year of construction: 2026, functionality: fully functional, operating pressure: 6 bar, inner dimension width: 600 mm, inner dimension height: 400 mm, volume flow: 10,500 m³/h, Equipment: documentation/manual, New Wire Mesh Belt Shot Blasting Machine RB-600 AH 4 Description: The RB-600 AH 4 wire mesh belt shot blasting machine from ABRAZIV Kft. is designed for the economical and continuous surface treatment of small to medium-sized workpieces. The machine is suitable for descaling, derusting, cleaning, and surface preparation of aluminum and steel castings, forgings, and workpieces that cannot be shot blasted in bulk. The machine is manufactured to order and can be configured individually according to customer requirements. The RB-600 AH 4 is equipped with four ABR-380 shot blasting turbines. Two turbines are located above and two below the wire mesh conveyor belt. This arrangement ensures optimal coverage of the cross-section and a uniform blasting result. The turbines operate at an angle of approximately 70° to the direction of travel and have eight blasting blades and a pre-accelerator. The active blasting area is lined with highly wear-resistant manganese steel. Other internal areas are protected by wear-resistant, noise-reducing rubber. The wire mesh belt is made of highly wear-resistant spring steel. A closed blasting media circuit with a screw conveyor, bucket elevator, blasting media cleaning system, and dosing system ensures reliable operation. Three-layer rubber curtains reduce blasting media leakage. An adjustable high-pressure blow-off system cleans the workpieces after the blasting process. The extraction and filter system with cartridge filters achieves a dust emission of max. 3 mg/m³. Technical Data Passage Passage width: 600 mm Max. workpiece height: 400 mm Min. workpiece length: approx. 1,000 mm Shot Blasting Turbines Number: 4 Type: ABR-380 Turbine diameter: 380 mm Speed: 2,800 1/min Blasting media output per turbine: 120 kg/min Wire Mesh Conveyor Belt Load capacity: 500 kg/m Speed: 0–4 m/min Power Consumption Base machine: 45.5 kW Cartridge filter: 7.5 kW Compressed air: min. 6 bar Compressed air consumption filter: 12.5 m³/h Other Data Blasting media capacity: approx. 1,000 kg Blasting media grain size: 0.4–1.2 mm Extraction capacity: 10,500 m³/h Filter area: 252 m² Dust emission: max. 3 mg/m³ Electrical Data Mains voltage: 3 × 400 V Control voltage: 220 V Frequency: 50 Hz Optional accessories available Magnetic drum separator Frequency converter Automatic blasting media dosing Special paint finish Transport Assembly Commissioning Operator training Djdpfx Ajzkivtob Tjkp Spare parts supply Maintenance and service Applications Aluminum and steel castings Forgings Small steel components Single and series components Descaling Derusting Cleaning Surface preparation Location / Production Lichtenfels (Germany) / Kecskemét (Hungary) As a manufacturer, we produce shot blasting machines individually according to customer requirements. Other sizes and special designs are available. We will be happy to provide you with a non-binding offer. Price on request

Condition: excellent (used), operating hours: 2,103 h, functionality: fully functional, turntable diameter: 1,000 mm, power: 17 kW (23.11 HP), Equipment: documentation/manual, Rösler RDT 100 with filter system, overhauled and in very good condition - Rotating table with frequency-controlled speed - Turbine H28 11kW, frequency-controlled speed - Access via 2 doors for crane loading - Additional rubber protective mat for the rotating table Dsdjzilpaepfx Ab Tjkp - Filter system Year of manufacture: 2002 Operating hours: approx. 2,193 Rotating table diameter: 1000 mm Max. workpiece height: 470 mm Max. batch weight: 300 kg Number of impeller wheels: 1 Total weight: 2070 kg Rated power: 17 kW The system is sold without warranty. Warranty of 6 months if this system is installed by our qualified technician.

Condition: new, Year of construction: 2026, functionality: fully functional, air demand: 15 m³/h, pressure: 6 bar, compressed air connection: 6 bar, operating pressure: 6 bar, inner dimension width: 2,000 mm, inner dimension height: 650 mm, volume flow: 12,000 m³/h, tank capacity: 2,500 l, air pressure: 6 bar, suction capacity: 12,000 m³/h, New RB-2000 Conveyor Blast System Description: The RB-2000 conveyor blast system from ABRAZIV Kft. was developed for the economical surface treatment of steel sheets, profiles, tubes, and welded structures and is ideally suited for descaling, derusting, cleaning, and roughening steel surfaces. The system is manufactured to order and can be individually configured according to the customer's requirements. With a passage width of 2,000 mm and a workpiece height of up to 650 mm, the RB-2000 is particularly suitable for large and heavy workpieces. It offers maximum flexibility for demanding applications in steel construction, mechanical engineering, tank construction, and the metalworking industry. Dsdpfx Aozikaqsb Tekp The RB-2000 is equipped with four high-performance ABR-500 blast turbines. Two turbines are arranged above and two below the conveyor, ensuring optimal coverage of the cross-section and a uniform blasting result. The inner surfaces of the blasting chamber are lined with highly wear-resistant manganese steel. Other areas are protected by wear-resistant rubber, which simultaneously reduces noise levels. A closed blasting media circuit with a screw conveyor, bucket elevator, blasting media cleaning, and dosing system ensures reliable and economical operation. All functions of the system are operated via a central control unit. In addition to automatic operation, a manual mode is also available for maintenance work. Technical Data Passage Passage width: 2,000 mm Min. workpiece length: approx. 1,500 mm Max. workpiece height: 650 mm Blast Turbines Number: 4 Type: ABR-500 Turbine diameter: 500 mm Speed: 2,600 1/min Blasting media flow rate per turbine: 150–300 kg/min Conveyor Load capacity: 1,500 kg/m Speed range: 0–4 m/min Power Requirements Base machine: 59–103 kW Cartridge filter: 15 kW Compressed air: min. 6 bar Compressed air consumption (filter): 15 m³/h Other Data Blasting media capacity: 2,500 kg Recommended blasting media grain size: 0.4–1.2 mm Extraction capacity: 12,000 m³/h Mains voltage: 3 × 400 V Control voltage: 230 V Frequency: 50 Hz Optional Frequency inverter Extended conveyors Automatic height scanning Automatic blasting media dosing Special paint finish Transport Assembly Commissioning Operator training Spare parts supply Maintenance and service Application Areas The RB-2000 is particularly suitable for: Steel sheets Steel profiles Tubes Hollow profiles Welded structures Steel construction Mechanical engineering Tank construction Contract blasting operations Location / Manufacturing Lichtenfels (Germany) / Kecskemét (Hungary) As a manufacturer, we develop and produce our conveyor blast systems individually according to customer requirements. In addition to the RB-2000, other sizes and special versions are available. We will be happy to advise you on the design of the appropriate system and provide you with a non-binding offer. Price on request.

Condition: new, Year of construction: 2026, functionality: fully functional, New HC-1500 Suspension Monorail Shot Blasting Machine Description: The HC-1500 suspension monorail shot blasting machine from ABRAZIV Kft. has been developed for the economical surface treatment of cast, forged, and welded parts as well as smaller steel structures. It is ideally suited for descaling, derusting, cleaning, and roughening a wide variety of workpieces. The machine is manufactured to order and can be individually configured according to customer requirements. The HC-1500 features a Y-shaped suspension monorail with two carriers, which enables continuous operation. While one carrier is in the shot blasting process, the second can already be loaded or unloaded. The machine is equipped with three high-performance ABR-400 shot blasting turbines, which are arranged at different angles. This ensures uniform and thorough cleaning of complex workpiece geometries. The internal surfaces of the shot blasting chamber are lined with highly wear-resistant manganese steel in the active shot blasting area. Other areas are protected by wear-resistant rubber, which also reduces noise levels. A closed shot blasting media circuit with a collection hopper, screw conveyor, bucket elevator, air separator, and dosing system ensures reliable and economical operation. A high-performance cartridge filter with a fan is included in the scope of supply for the extraction and filtration of dust generated during the shot blasting process. All functions of the machine are operated via a central control unit. In addition to automatic operation, a manual mode is also available for maintenance work. Technical data Workpiece dimensions Maximum workpiece height: 2,000 mm Maximum workpiece diameter: 1,500 mm Shot blasting turbines Number: 3 Type: ABR-400 Turbine diameter: 400 mm Speed: 2,400 rpm Shot blasting media flow rate: 180 kg/min Motor power per turbine: 11 kW Suspension monorail Load capacity per carrier: 500 kg Power consumption Machine power: 37 kW Cartridge filter: 7.5 kW Compressed air: 6 bar Compressed air consumption: 8 m³/h Other data Shot blasting media capacity: 1,800 kg Recommended shot blasting media grain size: 0.4–1.2 mm Extraction capacity: 6,000 m³/h Supply voltage: 3 × 400 V Control voltage: 220 V Frequency: 50 Hz Optionally available: Electric hoist Extended suspension monorail Frequency inverter Automatic shot blasting media dosing Special coating Transport Installation Commissioning Operator training Spare parts supply Maintenance and service Dkedpfx Abozifcgs Tsp Application areas The HC-1500 is particularly suitable for: Cast and forged parts Welded structures Small steel structures Mechanical engineering Tank and apparatus construction Job-order shot blasting operations Location / Production Lichtenfels (Germany) / Kecskemét (Hungary) As a manufacturer, we develop and produce our suspension monorail shot blasting machines individually according to customer requirements. In addition to the HC-1500, other sizes and special designs are available. We will be happy to advise you on the design of the appropriate machine and provide you with a non-binding offer. Price on request

Condition: new, Year of construction: 2026, functionality: fully functional, pressure: 6 bar, compressed air connection: 6 bar, operating pressure: 6 bar, inner dimension width: 1,500 mm, inner dimension height: 450 mm, input voltage: 380 V, volume flow: 6,000 m³/h, tank capacity: 2,000 l, air pressure: 6 bar, Equipment: documentation/manual, New Conveyor Blast Machine RB-1650 Description: The RB-1650 conveyor blast machine from ABRAZIV Kft. has been developed for the economical surface treatment of steel sheets, profiles, tubes, and welded structures, and is ideally suited for descaling, derusting, cleaning, and roughening steel surfaces. The machine is manufactured to order and can be individually configured according to customer requirements. The RB-1650 is equipped with four high-performance ABR-400 blasting turbines. Two turbines are arranged above and two below the conveyor, ensuring optimal coverage of the cross-section and uniform blasting results. The inner surfaces of the blasting chamber are lined with highly wear-resistant manganese steel. Other areas are protected by wear-resistant rubber, which also reduces noise levels. A closed blasting media circuit with screw conveyor, bucket elevator, blasting media cleaning, and dosing system ensures reliable and economical operation. All functions of the machine are operated via a central control system. In addition to automatic operation, a manual mode is also available for maintenance work. Technical Data Passage Passage width: 1,650 mm Min. workpiece length: approx. 1,500 mm Max. workpiece height: 450 mm Blasting Turbines Number: 4 Type: ABR-400 Turbine diameter: 400 mm Speed: 2,600 1/min Blasting media output per turbine: 130 kg/min Conveyor Load capacity: 1,300 kg/m Speed range: 0–4 m/min Power Requirements Base machine: 44 kW Cartridge filter: 7.5 kW Compressed air: min. 6 bar Compressed air consumption (filter): 3.2 l/min Compressed air tank (filter): 250 l Other Data Blasting media capacity: 2,000 kg Recommended blasting media grain size: 0.4–1.2 mm Extraction capacity: 6,000 m³/h Mains voltage: 3 × 380 V Control voltage: 220 V Frequency: 50 Hz Optional Extras Frequency inverter Extended conveyors Automatic height scanning Automatic blasting media dosing Special coating Transport Assembly Commissioning Operator training Spare parts supply Maintenance and service Application Areas The RB-1650 is particularly suitable for: Djdpfxjzidyko Ab Tokp Steel sheets Steel profiles Tubes Hollow profiles Welded structures Steel construction Machine construction Tank construction Contract blasting operations Location / Production Lichtenfels (Germany) / Kecskemét (Hungary) As a manufacturer, we develop and produce our conveyor blast machines individually according to customer requirements. We will be happy to advise you on the design of the appropriate machine and provide you with a non-binding offer. Price Price on request.

Condition: refurbished (used), functionality: fully functional, air demand: 6 m³/h, compressed air connection: 6 bar, warranty duration: 6 months, workpiece weight (max.): 800 kg, Fully Overhauled Rubber Belt Blasting Machine GH-4 For sale is a fully overhauled rubber belt blasting machine GH-4, professionally refurbished by the manufacturer ABRAZIV. This machine is ideally suited for deburring, descaling, cleaning, and surface roughening of castings, forgings, press parts, and other bulk goods. Its robust design and reliable blasting technology make it versatile for use in foundries, forging shops, and the metalworking industry. The machine has been professionally overhauled (refurbished) and is in perfect technical condition, like new. It is immediately available and can be inspected by appointment. Technical Data Blasting Chamber Rubber belt width: 1,300 mm Belt drum diameter: 1,150 mm Maximum batch weight: 800 kg Blasting media capacity: 800 kg Blasting Turbines Number of turbines: 2 Power per turbine: 11 kW Connection Values Electrical connection power: 27.5 kW Compressed air connection: 6 bar Compressed air consumption: 6 m³/h Extraction capacity: 5,500 m³/h Dsdpfezicuajx Ab Tskp Condition Fully overhauled (refurbished) Technically inspected Immediately available As the manufacturer, we can also offer you the following services, if desired: Transport Installation Commissioning Operator training Spare parts supply Maintenance and service Location: Kecskemét, Hungary Inspection is possible at any time by prior appointment. Price on request.

Condition: excellent (used), functionality: fully functional, overall weight: 1,100 kg, workpiece width (max.): 230 mm, workpiece height (max.): 320 mm, No minimum price – guaranteed sale to the highest bidder! The system was only used for demonstration and testing purposes and is therefore in very good condition. TECHNICAL DETAILS Dkjdozh Nggspfx Ab Top Number of satellites (workpiece holders): 6 Number of spray nozzles: 6 Maximum workpiece height: 320 mm Maximum workpiece width: 230 mm Movement: Rotational movement of the satellites, horizontal up/down movement Settings: Adjustment of the number of strokes, speed, and height of the lifting movement MACHINE DETAILS Control system: PLC Siemens Total weight: 1,100 kg EQUIPMENT Light curtain

Condition: ready for operation (used), Year of construction: 2008, operating hours: 2,288 h, functionality: fully functional, machine/vehicle number: 936, workpiece weight (max.): 150 kg, power: 8 kW (10.88 HP), workpiece length (max.): 800 mm, workpiece width (max.): 600 mm, number of support arms: 16, No minimum price – guaranteed sale to the highest bidder! The machine is equipped with an optional support system and can therefore accommodate one large workpiece or a maximum of 16 smaller workpieces on the supports. TECHNICAL DETAILS Turbine power: 8 kW Workpiece size (single workpiece) max.: 800 x 600 mm Workpiece weight (single workpiece) max.: approx. 100 kg Number of positions in the support system: 16 Workpiece size (on support system) max.: 200 x 200 mm Workpiece weight (on support system) total max.: 150 kg Filter data Number of filter cartridges: 2 Total filter area: 20 m² Filter area per filter cartridge: 10 m² Air velocity: 1.25 m/min Dkedezh Nf Aspfx Ab Tjp Compressed air data Compressed air pressure: max. 4–5 bar Compressed air consumption: approx. 7 m³/h Compressed air connection: G 1″ Permissible negative pressure: max. 1,500 Pa Dust container: 20 l Residual dust content in the exhaust air: below 5 mg/m³ MACHINE DETAILS Control unit: Pulse/time: 24 V, 1 phase, 50 Hz Solenoid valves: Voltage: 24 V, 50 Hz Timer: Input/output voltage: 24 V, 50 Hz Operating hours: 2,288 h Fan data Air flow: 2,000 m³/h Static pressure: 1,800 Pa Total pressure: 2,000 Pa Power consumption: 2.2 kW Motor power: 1.1 kW Motor voltage: 400 V Motor frequency: 50 Hz Motor phases: 3 phases EQUIPMENT Filter cartridges with 10 m² filter area each Aluminum venturi tubes Solenoid valves, type CA 25 DD Timer CG 03.06/04 Filter group Pressure regulator Pressure gauge 1″ ball valve Dust container, 20 l Fan

Condition: excellent (used), OMSG LAUCO 100 N-SP4 Type: Roller conveyor Max. width of workpiece: 1.000 mm Max. height of workpiece: 400 mm MAx. loading/roller: 800 kg Nr. Of turbines: 4 Turbine wheel diameter: 350 mm Power of turbine: 7,5 kW Max. turbine flow: 105 kg/min x 4 Transport speed: 0,5 - 3 m/min Cleaner type: Airwash Filtering unit: Included FX20/1 Foundation: no Total width of machine: app. 5.500 mm Total height of machine: app. 4.500 mm Total length of machine: app. 12.000 mm Djdpezh H Ibefx Ab Tjkp Max installed power: app. 50 kW

Condition: used, functionality: fully functional, Nicolis Shot Peening System Dsdpfxjzhurnj Ab Tjkp Media reclaim

Condition: used, internal diameter 25 mm external diameter 39 mm wall strength 7 mm length in total 33 m jet hose Unused, but shows significant signs of storage wear Dkodpezg Nmwsfx Ab Tsp

Condition: excellent (used), Here, we offer a used Datona mobile sandblasting unit. Datona Mobile Sandblasting Unit DUO - 74 Liter SKU DT-55212 Advantages and disadvantages: 2.5 m long hose for a large reach Easy switching between blasting media thanks to the mixing valve When using soda, the surface of the workpiece is not damaged Description: This mobile sandblasting unit is used for removing paint and rust. Thanks to the two tanks, you can choose between two different blasting media. The mobile sandblasting unit operates with a pressure of 4 to 8 bar and requires a compressor with an intake capacity of at least 350 l/min. Double tank: If blasting with soda or calcium carbonate does not produce the desired result, simply try a different blasting medium. For a more effective result, it is also possible to use both blasting media simultaneously. With the sandblasting unit, you bring a practical machine into your home. With the help of the special mixing valve, you can easily and gently remove paint from steel, stainless steel, chrome, aluminum, or polyester using soda. A major advantage of blasting with fine soda is that the surface of the object being blasted is not damaged. You don't even have to remove rubber seals, chrome parts, or glass. This saves a lot of time! The mobile sandblasting unit can be used both in the workshop and on-site. Note: One tank is only suitable for soda and calcium carbonate!!! ✓ Duo sandblasting unit ✓ 74 liter tank capacity ✓ Air consumption is approximately 350 l/min Technical data: SKU DT-55212 Weight 33 kg Suitable blasting media Aluminum silicate Dato-Blast calcium carbonate Soda Connection for blasting cabinet 1/4" Dkodpfxjzgcbns Ab Tsp Max. pressure 2 - 6 bar Minimum air consumption 350 l/min Min. tank capacity compressor 100 liters Type: DT-55212 Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data, information is subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, Technical Data – AGTOS Abrasive Blast Machine Manufacturer: AGTOS Type: DHT 21-21-3.6-03-11 Year of Manufacture: 2015 Machine Dimensions Length: 10,420 mm Width: 12,750 mm Height: 6,600 mm Door Opening: 2,000 x 2,000 mm Workpiece Data Max. Workpiece Diameter: 2,100 mm Max. Workpiece Height: 2,100 mm Max. Hook Load: 2,000 kg Max. Workpiece Temperature: 80 °C Blasting System 6 High-Performance Turbines, Turbine Type: 3.6 Impeller Diameter: 380 mm Blade Width: 55 mm 6 Blades per Turbine Drive Power per Turbine: 11 kW Abrasive Flow Rate per Turbine: 242 kg/min Throwing Speed: approx. 75 m/s Filter System Filter Capacity: 15,000 m³/h Residual Dust Content in Exhaust Air: < 1 mg/m³ Electrical Data Supply Voltage: 3~400 V / 50 Hz Control Voltage: 230 V / 50 Hz Installed Total Power: 63 kW Compressed Air Operating Pressure: 4–6 bar Dkodpfx Aezf Unwjb Tep Compressed Air Consumption, Blasting Machine: approx. 0.5 m³/h Compressed Air Consumption, Compressed Air Tank: approx. 9.1 m³/h Application Area Desanding and cleaning of castings Surface preparation before painting or coating Steel, cast iron, and forged parts up to 2,000 kg piece weight Special Feature: Modern hook-on blasting machine with 6 turbines, 2-ton load capacity, and a powerful 15,000 m³/h filter system. Ideal for foundries, forging plants, and contract blasting operations.

Condition: used, Year of construction: 2006, functionality: fully functional, air demand: 4,000 m³/h, pressure: 5 bar, operating pressure: 7 bar, inner dimension width: 900 mm, workpiece weight (max.): 1,000 kg, filter area: 120 m², input voltage: 380 V, working range: 1,400 mm, tank capacity: 960 l, suction capacity: 4,000 m³/h, Equipment: cabin, documentation/manual, Automatic hook-type shot blasting system complete with monorail overhead conveyor, abrasive recovery system, bucket elevator, pneumatic shot selector, vibrating screen, dust collection filter, and control panel. Main features: Maximum workpiece diameter: 900 mm Maximum workpiece height: 1,400 mm Maximum load weight: 1,000 kg No. 6 hook holders No. 4 Carlo Banfi X1 centrifugal turbines Turbine power: 4 x 7.5 kW Abrasive flow rate: 300 – 360 kg/min Abrasive capacity (initial charge): 960 kg Power supply: 380 V three-phase – 50 Hz Total installed power: approximately 22 kW Carlo Banfi PS-6B dust collection filter included: Air flow rate: 4,000 m³/h Dkjdpfszdqtmsx Ab Tsp Filter area: 120 m² No. 6 microfibre filter cartridges 4 kW suction fan Automatic cartridge cleaning system with compressed air Required compressed air pressure: 5 – 7 bar System suitable for shot blasting and surface cleaning of castings, metal structures, mechanical components, stamped parts, and steel products. Machine complete with shot recovery and recycling system, electrical panel, and original technical documentation. Includes spare parts, including motors and parts for the blasting chamber. Video of the machine in operation available upon request. Another identical shot blasting machine is available.

Condition: used, Year of construction: 2013, operating hours: 11,188 h, total height: 5,000 mm, inner dimension width: 250 mm, inner dimension height: 250 mm, workpiece weight (max.): 15 kg, Rotary indexing – shot blasting machine – shot peening Used for cold hardening of transmission components. Manufacturer: AUER Type: SA 1100 S5 Year of manufacture: 2013 Operating hours: 11,188 h Workpiece height: 250 mm Workpiece diameter: 250 mm Workpiece weight: 15 kg Number of satellites/stations: 5 - Workpiece loading/unloading - Airlock - inlet - Blasting position 1 - Blasting position 2 - Airlock - outlet / cleaning Number of nozzles: 12 (individually controlled) Including filter system Overall height: 5.00 m Other dimensions, see photos. Djdezdk Nnspfx Ab Tokp Well-maintained machine, from a highly reputable company, regularly serviced. The machine can still be inspected while powered on.

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, workpiece weight (max.): 12 kg, power: 45 kW (61.18 HP), controller model: SIEMENS Simatic, TECHNICAL DETAILS Drum diameter: 400 mm Maximum workpiece length: 700/1,000 mm Maximum individual workpiece weight: 12 kg Dodpfjzcl I Dex Ab Tekp Load capacity: 100 kg MACHINE DETAILS Control system: SIEMENS Simatic Installed power: 45 kW Centrifugal wheels: 4 units Centrifugal wheel type: Hurricane H 28 Power per centrifugal wheel: 7.5 kW

Condition: used, Year of construction: 2003, functionality: fully functional, We offer this used Schlick sandblasting system, manufactured in 2003, for sale. It features a throwing wheel, a centrifugal wheel, and a pressure tank, as well as fully automatic sand filters and a conveying system. It also includes dust extraction and electronically controlled conveying wheels. The system is in very good working order. We offer professional dismantling and reassembly services within Switzerland at very favorable conditions. Dkodezbzwxepfx Ab Top Year of manufacture: 2003 Factory number: 24/23717 Type: If you have any questions or require further information, please feel free to send us a message or call us.

Condition: new, Year of construction: 2026, functionality: fully functional, Blasting container, 40 ft, with 9 m blasting chamber, screw conveyor floor (very low maintenance), blasting media preparation, and filtration system. Dkodpjzbztajfx Ab Top Chamber dimensions (internal): approx. length = 8850 mm, height = 2485 mm, width = 2250 mm. Option: width including widening = 3240 mm. Transport height: approx. 3000 mm. Floor height: approx. 440 mm. Options: - Side container opening for 9 m and 3 m machine room - Side extension for widening the blasting chamber - Crane roof opening (not possible with side opening) - Crane track, 500 kg and much more upon request.

Condition: ready for operation (used), ROLLER-TYPE SHOT BLASTING MACHINE MANUFACTURER: USF SCHLICK RB 2100 Shot blasting processing of cut-to-size parts, profiles, and sheets. Manufacturer: USF Schlick Year of manufacture: 2001 Type: RB 2100 Passage width: 2100 mm Passage height: 450 mm Blast wheels: 4 x 11 kW Infeed roller conveyor: approx. 6,200 mm + approx. 20 m Outfeed roller conveyor: approx. 9,000 mm Blow-off and brushing station: YES Filter system: Yes Cross conveyor: Yes Includes control cabinet, filter system Price: Loaded onto truck .-€ Warranty: 6-month functional and warranty guarantee upon commissioning by DECK Sarl. Spare parts supply for the next 10 years. Dksdpozbyluofx Ab Tsp OPTIONAL: Delivery / Assembly / Commissioning / Training We also offer spare parts for Rösler, Schlick, Wheelabrator, Gietart, etc. shot blasting machines!

Condition: used, Year of construction: 1978, functionality: fully functional, air demand: 300 m³/h, pressure: 6 bar, total height: 3,800 mm, We offer a Škoda blasting booth. The equipment is fully functional and in working order. A test run is possible. Internal working space dimensions: 2900×2900×2900mm. The booth features a floor-level abrasive collection system, abrasive transport to the abrasive cleaning unit, a blasting unit, and a filtration unit. Dsdpfezbrgdox Ab Tskp Complete equipment.

Condition: good (used), Tumble rubber belt blast machine Max. batch volume: 140 L Max. batch weight: 300 kg Max. component weight: 10 kg Compartment diameter: 700 mm Compartment width: 850 mm Nr. Of turbines: 1 Power of turbine: 4 kW Max. turbine flow: 56 kg/min Cleaner type: air Foundation: no Housing protection: Mn + rubber Filtering unit: YES Max. installed power: app. 12 kW !!! NEW Rubber bel installed !!! Dodpfx Aszbrftsb Tekp

Condition: good (used), Tumble rubber belt blast machine Dkodpfxjza Eq Tj Ab Tjp Max. batch volume: 250 L Max. batch weight: 300 kg Max. component weight: 10 kg Compartment diameter: 900 mm Compartment width: 930 mm Nr. Of turbines: 1 Power of turbine: 7,5 kW Max. turbine flow: 105 kg/min Cleaner type: air Foundation: no Housing protection: Mn + rubber Filtering unit: YES 2.000 m3/h Max. installed power: app. 15 kW

Condition: used, Year of construction: 2007, functionality: fully functional, machine/vehicle number: 3863, For sale is a used, but fully functional, Auer blasting cabinet. Dsdszampkjpfx Ab Tekp

Condition: used, Year of construction: 2002, 1. Shot blasting machine CARLO BANFI SCM4R/12X18.5/X1/10 Serial number: 4965 Year of manufacture: 2002 Technical specifications: Dimensions of the fixture (cluster): 1200 × 18050 mm Maximum weight of a single fixture: 500 kg 4 turbines, model X1 Turbine diameter: 300 mm Rotational speed: 2900 rpm 1 self-cleaning bag filter P.J.60/B/S.R. Starting price: 20,000 EUR 2. Shot blasting machine CARLO BANFI SCM3R/F.500/12X18.5/X1 Serial number: 4223 Year of manufacture: 1994 Technical specifications: Dimensions of the fixture (cluster): 1200 × 18050 mm Maximum weight of a single fixture: 500 kg 3 turbines, model X1 Turbine diameter: 300 mm Rotational speed: 2900 rpm 1 self-cleaning bag filter P.J.60/B/S.R. Starting price: 15,000 EUR 3. Two-track overhead conveyor FUTURA type DR44 Serial number: 045/2002 Dsdszaizvjpfx Ab Tekp Year of manufacture: 2002 Technical specifications: 2 caterpillar-type drive units Total track length: 150 m Adjustable speed: 3.4–8 m/min Allowable load per hook: 300 kg Number of hooks: 33 Starting price: 50,000 EUR. The line is located at the parent company in Italy, near Pordenone. Direct contact is possible after prior arrangement.

Condition: excellent (used), Year of construction: 2012, functionality: fully functional, ROTARY TABLE SHOT BLASTING MACHINE WITH FILTER Designation: Rotary Table Shot Blasting Machine Manufacturer: Rösler Year of Manufacture: 2012 Type: RDT 100 Rotary Table Diameter: 1,000 mm Maximum Workpiece Height: 470 mm Blast Wheels: 1 unit, 7.5 kW each Consisting of: - Rotary Table Shot Blasting Machine - Control Cabinet - Filter System Designation: Table Shot Blaster Brand: Rösler Dkodpfxjy Uimpe Ab Tep Type: RDT 100 Year: 2012 Table Diameter: 1,000 mm Maximum Piece Height: 470 mm Shot Wheel: 1 piece, 7.5 kW Consisting of: - Table Shot Blaster, Type: RDT 100 - Main Panel - Filter Price: Loaded onto truck from F-67620 Soufflenheim Warranty: 6-month functional and warranty guarantee upon commissioning by DECK Sarl. Spare parts supply for the next 10 years. OPTIONAL: Delivery / Installation / Commissioning / Training We also offer spare parts for Rösler shot blasting machines!