Condition: refurbished (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, year of last overhaul: 2025, Technical data packing press / can press / metal sheet press: Manufacturer unoTech GmbH Type UPAXX 70 Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Connected load 40 kW Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Lodpfjy S Rv Tjx Adwehg Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: The packing press has been fully overhauled in our workshop. The press is in very good condition; please see the demonstration video following the overhaul. The machine sustained transport damage whilst being moved. The control cabinet was damaged and slightly dented by a forklift truck, and the main switch (on/off switch) was damaged. These damages are reflected in the significantly reduced sale price and must be repaired by the buyer at their own expense. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2026, volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Lhsdpfxoy S Ru Ao Adweg Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2015, operating hours: 30,143 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, year of last overhaul: 2026, volume flow: 800 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Lhodpfx Aoy S Rtlsdwog Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, empty load weight: 50,800 kg, year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. Lhsdpfjy S Rrusx Adweg • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. Lsdpfey S Rqwex Adwjhg 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: used, Year of construction: 2015, No. 10033 Wet drum magnetic separator Steinert WDS 92 92 (without CE package) Used, year of construction 2015 According to our customer / the previous owner, the machine is fully functional and can be viewed on site Without CE package Highly efficient recovery of FeSi or magnetite from float-sink separation and wet processing of fines The Steinert WDS is particularly popular in the processing of heavy sludge or iron ore with grain sizes between 1 µm and 3 mm. In the regeneration of heavy beet, the wet drum magnetic separator essentially ensures the recovery of magnetite or ferrosilicon (FeSi). High field strengths are achieved through the use of powerful magnets made of neodymium-iron-boron and the special design of the magnet packs, making high separation rates of over 99 % possible. Ljdjyl Sqwepfx Adwehg Sale on behalf of customer, ex location near 54634 Bitburg, without dismantling, transport and assembly Dismantling, transport and loading by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Technical specifications, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or shipment Terms of delivery: ex location

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, total width: 3,375 mm, total length: 4,500 mm, WEIMA Crusher Series HWV 3000 (37 kW) and the Single-Shaft Shredder WL12 (30 kW) Ideal for pre-shredding wood waste such as pallets, followed by metal separation and secondary shredding. Advantages: Two-stage process: Pre- and post-shredding for maximum efficiency. Versatile use: Wood chips for heating systems or briquetting presses. Low-noise operation Technical details – HWV 3000: - Power: 37 kW - Dimensions (hopper): 3375 mm width x 1630 mm height - Cutting knives: 58 knives in two rows Technical details – WL12/30: - Power: 30 kW - Shaft diameter: 368 mm - Screen: 15/20 mm Applications - Wood waste processing and recycling - Energy generation through wood chips or briquetting Lhedpjy Ubvpefx Adwog

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale Lhedpjvq Rtksfx Adwog - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: like new (used), Year of construction: 2025, functionality: fully functional, ALTERO VELOX 140 RECYCLING LINE Regranulation line for plastic recycling Brand: Altero Model: Velox 140 Feeding belt with metal detection Compactor/Agglomerator with 1500 mm diameter Screw diameter: 140 mm Double degassing unit Lhsdoy T R Dyepfx Adwog Laser filter Granulation system with die-face cutter Centrifuge and vibrating screen Production up to 1100 kg/h Control panel with touchscreen Year 2025

Year of construction: 2018, condition: good (used), For sale: a machine for pelletizing. ARtechnic PBPe.500x-k. Ledpfxoy T Itxe Adwohg

Condition: excellent (used), Year of construction: 2016, bale weight: 480 kg, For sale: HSM HL 4809I baling press. Ljdpfxey T Iqdo Adwehg

Condition: used, Year of construction: 2021, functionality: fully functional, For sale: HSM 7009st baler and conveyor belt. Lhsdpfx Adjy T Inpewog

Condition: as good as new (ex-display), Year of construction: 2023, operating hours: 2 h, functionality: fully functional, Cable Granulation Plant GUIDETTI SINCRO MILL 530 + Pre-shredder PMG-H 900 – Immediately Available – As New For sale is a high-quality cable recycling plant from the Italian manufacturer Guidetti, consisting of: • Guidetti Sincro Mill 530 cable granulation plant • Guidetti PMG-H 900 pre-shredder • External filtration unit The system was installed, tested at a customer site, and then professionally dismantled. Due to a project change, the plant is now for sale. Condition: Nearly new (test operation only) Availability: Immediate ex stock – no lead time Price: Significant savings compared to new equipment — Special advantages: • Immediately available – no long lead times as with new machines • Only operated for test purposes – correspondingly minimal wear • Complete system incl. pre-shredder • Proven Guidetti technology — Ljdpfx Adsy Ahlyowohg Description: The Sincro Mill 530 is a compact, fully integrated cable granulation plant for processing mixed copper and aluminum cables – without pre-sorting. The system consists of: • Granulator (cutter mill) • Zig-zag separator • Turbo mill for fine grinding • Dry separation table Material purity up to 99% can be achieved. In combination with the PMG-H 900 pre-shredder, the system offers a high-performance recycling line for industrial applications. — Technical Data Sincro Mill 530: • Throughput: 450 – 600 kg/h • Motor power: 53 kW • Dimensions (L x W x H): 3410 x 1515 x 4395 mm • Weight: approx. 2,700 kg • For processing copper and aluminum cables — Technical Data Pre-shredder PMG-H 900: • Power: approx. 38.5 kW • Dimensions (L x W x H): 2110 x 2070 x 2245 mm • Weight: approx. 2,840 kg Suitable for pre-shredding cables, non-ferrous metals, and plastics. — Note: The plant is available at short notice. Subject to prior sale. Inspection by appointment possible.

Condition: ready for operation (used), Year of construction: 2007, The Vecoplan VAZ 2000 M F-T is a robust heavy-duty single-shaft shredder manufactured in 2007 for industrial recycling applications. Suitable for plastics, films, wood, paper, cardboard, EBS/RDF, and commercial waste. Formerly part of a production line for LDPE PCR film bales; the production line was modernized and rebuilt in 2024. Successful tests for processing used pallets and cardboard cores have been carried out. The processing of wood and cardboard cores is technically unproblematic. The machine condition has been documented by Vecoplan, and the required spare parts for recommissioning have already been ordered. The sale is due to an internal department closure and the associated restructuring of operational processes. Rotor length approx. 2,000 mm, hydraulic ram for uniform material feeding, flipper/airspring counter-knife system for high operational reliability, Torque/HiTorc drive for high torque and energy-efficient operation, replaceable reversible cutting inserts, suitable for both pre-shredding and secondary shredding, final particle sizes depending on screen and material approx. 10–250 mm, high throughput capacity, and robust, maintenance-friendly design. Inspection possible by appointment. Lhjdpfx Aey T Hbbedwjg

Condition: excellent (used), functionality: fully functional, cutting length (max.): 330 mm, Equipment: type plate available, Plastic shredder mill, for processing copper, spheroidal graphite, cork, etc. Lsdpfxsy T Ha Ds Adwshg

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, pressing force: 50 t, bale length: 1,200 mm, bale weight: 500 kg, Equipment: safety light barrier, For sale: HSM 3521s machine, manufactured between 2015 and 2023. Lsdpfx Adjy T Empowohg

Condition: used, Included container 28,5 m3 Ledsv Hpn Sspfx Adwshg

Year of construction: 2018, condition: excellent (used), From 2018, 15 kW, with hopper and container PM 32-E (32 m3) and tipping device Lhodeyti Ipopfx Adwog

Condition: good (used), weight 120 kg length 800 mm width 600 mm height 330 mm Remaining stock of new and used milling cutters with bore, end mills, drills, dowel drills, inserts and various other cutters. Lhsdpfx Adsy Aa I Towog Manufacturer: Leitz, Leuco, Oppold, and many more Interesting for every well-equipped sharpening room.

Condition: excellent (used), total power requirement 31,7 kW Lodpfxjyvvtro Adwohg main drive 7,5 kW Input width 550 mm ca. 25/75 mm ventilator 22kW / 10.800 m³/h Industrial shredder or shredder line with carbide knives for shredding various materials such as wood, cardboard, glass fiber mats or similar, e.g. as pre-treatment for recycling processes. The system consists of two infeed conveyor belts, the chipper and a transport fan.

Year of construction: 2015, operating hours: 9,400 h, condition: excellent (used), functionality: fully functional, Used Terex Finlay 883+ Tracked Screening Plant Year 2015 Ljdpfxoy Tyw Ao Adwehg CAT Engine 9400 Hrs Steel Apron Feeder Fingers Top Deck and Square Mesh Rubber Mat BTM Deck All New Chains & Sprockets On The Tracks All Belts And Serviceable Items In Very Good Condition

Condition: excellent (used), Year of construction: 2021, operating hours: 900 h, functionality: fully functional, overall weight: 26,000 kg, Used Omega J1065S Semi Mobile Jaw Crushing Plant Lhsdpfjy Tyt Rex Adwog Year 2021 900 Hrs 1000 x 650 Jaw Box (Same as the Extec C10 / Sandvik 241 Box) Complete Plant Consisting Of Grizzly Feeder, Jaw Box, Overband Magnet, Discharge Conveyor, Walkways Approx Weight 26 Tonne Comes With Control Panel & Generator Excellent Condition Throughout

Year of construction: 2022, condition: reconditioned (used), functionality: fully functional, Used Neuenhauser Star Screen FULL FACTORY REFURBISHMENT Year 2022 Measures 7 metres long x 1.25m wide Lodpfxex Nc Dqo Adwohg ALL NEW PARTS -10mm / +10mm Product Size (With Adjustment) Hydraulic Drive via 5 Hydrauilc Motors

Year of construction: 2026, condition: new, FTS 15-60 is a compact and heavy steel structured trucked plant with three-decks screen. Also integrated with tracked moving system and robust structure. Works via conveyor belt system. The fully electrically driven plant is designed in a variety for maximum capacities and suitable for feeding materials with a maximum edge length of 200 mm. All functions, as well as subsequent and previous crushing plants, conveyor belts, etc. are electrically lockable. • Production capacity: 500-600 TPH • Screen dimension: 1550x6100mm • Mobile three-decks screen Ledpfey Twq Tjx Adwjhg • Diesel electric drive • Classifier screen plant up to 4 final fraction sizes Maximum feeding size 100 x 160 mm

Year of construction: 2026, condition: new, FABO Mobile Scalper screen is produced for aggregate producers who require higher productivity and versatility. The machine can be used for multiple purposes; it can be used as a heavy-duty incline 2 deck screen, capable of stockpiling, scalping before and after crushing units, or it can be used a standalone system as well. That is why FABO tracked mobile scalpers can separate the hardest materials. FABO Mobile Scalpers helps our customers to maximize productivity while on the other hand helps on reducing the production costs. - - - Technical Specifications of the Tracked Scalper Screen: - *Bunker capacity :7m³ - *Production capacity : 220 – 400 Tons per hour - *Vibrating Screen Size : 1530x4800 mm - *Total Power : 110 kvA - *Weight : 31.000 kg Lhsdpfey Twq Hox Adwsg - *The screen angle varies between 18-27°.